最新10月CCNA題庫word版151~200題

1、question 151refer to the topology and router output shown in the exhibit. a technician is troubleshooting hostconnectivity issues on the switches. the hosts in vlans 10 and 15 on sw11 are unable to communicatewith hosts in the same vlans on sw12. hosts in the admin vlan are able to communicate. the

2、port-to-vlan assignments are identical on the two switches. what could be the problem?a. the fa0/1 port is not operational on one of the switches.b. the link connecting the switches has not been configured as a trunk.c. at lease one port needs to be configured in vlan 1 for vlans 10 and 15 to be abl

3、e to communicate.d. port fastethernet 0/1 needs to be configured as an access link on both switches.e. a router is required for hosts on sw11 in vlans 10 and 15 to communicate with hosts in the samevlan on sw12.question 152you have finished physically installing an access point on the ceiling at you

4、r office. at a minimum, whichparamenter must be configured on the access point in order to allow a wireless client to operate on it?a. aesb. pskc. ssidd. tkipe. wepquestion 153refer to the exhibit. a network administrator needs to add a new vlan, named vlan3, to the networkshown. unfortunately, ther

5、e is not another fastethernet interface on r1 to connect to the new vlan3.which approach is the most cost effective solution for this problema. purchase a new fastethernet module and install it on r1b. replace r1 with a new router that has at least three fastethernet interfaces.c. configure a second

6、 switch to support vlan3 with a vlan trunk between sw1 and the new switch.d. configure a single vlan trunk between r1 and sw1 and configure subinterface on r1 interface foreach vlan.e. connect another router to a serial interface of r1. use a fastethernet interface on the new router forvlan3question

7、 154refer to the exhibit. when running eigrp, what is required for routera to exchange routing updates withrouterca. as numbers must be changed to match on all the routers.b. loopback interface must be configured so a dr is elected.c. the no auto-summary command is needed on router a and router c.d.

8、 router b needs to have two network statements, one for each connected networkquestion 155refer to the exhibit. the two exhibit devices are the only cisco devices on the network. the serial networkbetween the two devices has a mask of 52. given the output that is shown, what threestatem

9、ents are true of these devices? (choose three.)a. the manchester serial address is b. the manchester serial address is c. the london router is a cisco 2610.d. the manchester router is a cisco 2610.e. the cdp information was received on port serial0/0 of the manchester router.f. the c

10、dp information was sent by port serial0/0 of the london router.question 156how is an eui-64 format interface id created from a 48-bit mac address?a. by appending 0xff to the mac address.b. by prefixing the mac address with 0xffee.c. by prefixing the mac address with 0xff and appending 0xff to it.d.

11、by inserting 0xfffe between the upper three bytes and the lower three bytes of the mac addresse. by prefixing the mac address with 0xf and inserting 0xf after each of its first three bytes.question 157refer to the exhibit. after a rip route is marked invalid on router_1, how much time will elapse be

12、fore thatroute is removed from the routing table?question 158refer to the exhibit. a network associate has configured the internetwork that is shown in the exhibit, buthas failed to configure routing properly.which configuration will allow the hosts on the branch lan to access resources on the hq la

13、n with theleast impact on router processing and wan bandwidth?a. hq(config)# ip route branch(config)# ip route b. hq(config)# router riphq(config-router)# network hq(config-router)# network branch(config)#

14、 router ripbranch(config-router)# network branch(config-router)# network c. hq(config)# router eigrp 56hq(config-router)# network hq(config-router)# network branch(config)# router eigrp 56branch(config-router)# network branch(config-router)# net

15、work d. hq(config)# router ospf 1hq(config-router)# network area 0hq(config-router)# network 55 area 0branch(config)# router ospf 1branch(config-router)# network 55 area 0question 159which additional configuration step is necessary

16、 in order to connect to an access point that has ssidbroadcasting disabled?a. set the ssid value in the client software to public.b. configure open authentication on the ap and the client.c. set the ssid value on the client to the ssid configured on the ap.d. configured mac address filtering to perm

17、it the client to connect to the ap.question 160what is one reason that wpa encryption is preferred over wep?a. a wpa key is longer and requires more special characters than the wep key.b. the access point and the client are manually configured with different wpa key values.c. wpa key values remain t

18、he same until the client configuration is changed.d. the values of wpa keys can change dynamically while the system is used.question 161a network administrator is troubleshooing an eigrp problem on a router and needs to confirm the ipaddresses of the devices with which the router has established adj

19、acency. the retransmit interval and thequeue counts for the adjacent routers also need to be checked. what command will display the requiredinformation?a. router# show ip eigrp adjacencyb. router# show ip eigrp topologyc. router# show ip eigrp interfacesd. router# show ip eigrp neighborsquestion 162

20、all wan links inside the abc university network use ppp with chap for authentication security. whichcommand will display the chap authentication process as it occur between two routers in the network?a. show chap authenticationb. show interface serial0c. debug ppp authenticationd. debug chap authent

21、icatione. show ppp authentication chapquestion 163refer to the exhibit. a network technician is asked to design a small network with redundancy. the exhibitrepresents this design, with all hosts configured in the same vlan. what conclusions can be made aboutthis design?a. the design will function as

22、 intendedb. spanning-tree will need to be used.c. the router will not accept the addressing scheme.d. the connection between switches should be a trunk.e. the router interfaces must be encapsulated with the 802.1q protocol.question 164refer to the exhibit. how should the fastethernet0/1 port on the

23、2950 model switches that are shown in theexhibit be configured to allow connectivity between all devices?a. the ports only need to be connected by a crossover cable.b. switchx(config)# interface fastethernet 0/1switchx(config-if)# switchport mode trunkc. switchx(config)# interface fastethernet 0/1sw

24、itchx(config-if)# switchport mode accessswitchx(config-if)# switchport access vlan 1d. switchx(config)# interface fastethernet 0/1switchx(config-if)# switchport mode trunkswitchx(config-if)# switchport trunk vlan 1switchx(config-if)# switchport trunk vlan 10switchx(config-if)# switchport trunk vlan

25、20question 165ip address and routing for the network are configured as shown in the exhibit. the network administratorissues the show ip eigrp neighbors command from router1 and receives the output shown below thetopology. which statement is true?a. it is normal for router1 to show one active neighb

26、or at a time to prevent routing loops.b. routing is not completely configured on router3.c. the ip addresses are not configured properly on the router1 and router3 interfaces.d. the no auto-summary command configured on the routers prevents router1 and router2 from forminga neighbor relationship.que

27、stion 167refer to the exhibit. the output that is shown is generated at a switch. which three of these statements aretrue? (choose three.)a. all ports will be in a state of discarding, learning, or forwarding.b. thiry vlans have been configured on this switch.c. the bridge priority is lower than the

28、 default value for spanning tree.d. all interfaces that are shown are on shared media.e. all designated ports are in a forwarding state.f. the switch must be the root bridge for all vlans on this switch.question 168refer to the exhibit. a network administrator attempts to ping host1 from host1 and r

29、eceives the result thatare shown. what is a possible problem?a. the link between host1 and switch1 is down.b. tcp/ip is not functioning on host1.c. the link between router1 and router2 is down.d. the default gateway on host1 is incorrect.e. interface fa0/0 on router1 is shudown.f. the link between s

30、witch1 and router1 is down.question 169refer to the exhibit. the bigtime router is unable to authenticate to the littletime router. what is the causeof the problem?a. the usernames are incorrectly configured on the two routers.b. the passwords do not match on the two routers.c. chap authentication c

31、annot be used on a serial interface.d. the routers cannot be connected from interface s0/0 to interface s0/0.e. with chap authentication, one router must authenticate to another router. the routers cannot beconfigured to authenticate to each other.question 170s0/0 on r1 is configured as a multipoint

32、 interface to communicate with r2 and r3 in the hub-and-spokeframe relay topology shown in the exhibit. originally, static routes were configured between these routersto successfully route traffic between the attached networks. what will need to be done in order to useripv2 in place of the static ro

33、utes?a. configure the no ip subnet-zero command on r1, r2, and r3.b. dynamic routing protocols such as ripv2 cannot be used across frame relay networks.c. configure the s0/0 interface on r1 as two subinterfaces and configure point-to-point links to r2 and r3.d. change the /25 and 172.16.2.

34、128/25 subnetworks so that at least two bits are borrowed fromthe last octet.e. change the network address configuration to eliminate the discontiguous /25 and28/25 subnetwork.question 171refer to the exhibit. a router interface is being configured for frame relay. however, as th

35、e exhibit shows,the router will not accept the command to configure the lmi type. what is the problem?a. the interface does not support frame relay connections.b. the interface does not have an ip address assigned to it yet.c. the interface requires that the no shutdown command be configured first.d

36、. the interface requires that the encapsulation frame-relay command be configured first.question 172refer to the exhibit. two buildings on the san jose campus of a small company must be connected to useethernet with a bandwidth of at least 100 mbps. the company is concerned about possible problems f

37、romvoltage potential difference between the two buildings. which media type should be used for theconnection?a. utp cableb. stp cablec. coaxial cabled. fiber optic cablequestion 173users have been complaining that their frame relay connection to the corporate site is very slow. thenetwork administra

38、tor suspects that the link is overloaded. based on the partial output of the router#show frame relay pvc command shown in the graphic, which output value indicates to the local routerthat traffic sent to the corporate site is experiencing congestion?a. dlci = 100b. last time pvc status changed 00:25

39、:40c. in becn packets 192d. in fecn packets 147e. in de packets 0question 174refer to the exhibit. a router boots to the prompt shown in the exhibit. what does this signify, and howshould the network administrator respond?a. this prompt signifies that the configuration file was not found in nvram. t

40、he network administratorshould follow the prompts to enter a basic configuration.b. the prompt signifies that the configuration file was not found in flash memory. the networkadministrator should use tftp to transfer a configuration file to the router.c. the prompt signifies that the ios image in fl

41、ash memory is invalid or corrupted. the networkadministrator should use tftp to transfer an ios image to the router.d. the prompt signifies that the router could not authenticate the user. the network administrator shouldmodify the ios image and reboot the router.question 175refer to the exhibit. gi

42、ve this output for switchc, what should the network administrator's next action be?a. check the trunk encapsulation mode for switchc's fa0/1 port.b. check the duplex mode for switchc's fa0/1 port.c. check the duplex mode for switcha's fa0/2 port.d. check the trunk encapsulation mode

43、for switcha's fa0/2 port.question 176refer to the exhibit. which of these statements correctly describes the state of the switch once the bootprocess has been completed?a. as fastethernet0/12 will be the last to come up, it will not be blocked by stp.b. remote access management of this switch wi

44、ll not be possible without configuration change.c. more vlans will need to be created for this switch.ccna考試報(bào)名1700元 84艾迪飛論壇 艾迪飛論壇 d. the switch will need a different ios code in order to support vlans and stp.question 177refer to the exhibit. which of these statements correctly describes the state o

45、f the switch once the bootprocess has been completed?a. only the default vlans are configured on switcha.b. switcha does not have a vtp domain name configured.c. vtp pruning needs to be enabled on switcha.d. switchc needs to have the vtp domain name configured.e. switchb is in transparent mode.quest

46、ion 178refer to the exhibit. the network administrator has discorvered that the vlan configuration of switchc isnot synchronized with the rest of the switched network. why is switchc not receiving vtp updates?a. switchb is not relaying vtp advertisements to switchc.b. switchc has fewer existing vlan

47、s than does switcha.c. switcha supports a greater number of vlans than does switchc.d. switchc has revision number higher than that being advertisedccna考試報(bào)名1700元 86艾迪飛論壇 艾迪飛論壇 e. switchc should be operating in vtp server mode to recevie vtp updates.f. switchb should be operating in vtp server or cli

48、ent mode to relay vtp updates.question 179how many subnets can be gained by subnetting /23 into a /27 mask, and how many usable hostaddresses will there be per subnet?a. 8 subnets, 31 hostsb. 8 subnets, 32 hostsc. 16 subnets, 30 hostsd. 16 subnets, 32 hostse. a class b address can't b

49、e subnetted into the fourth octet.question 180a tcp/ip transfer is diagrammed in the exhibit.a window size of three has been negotiated for this transfer. which message will be returned from thereceiver to the sender as part of this tcp/ip transfer?a. send ack 1-3b. send ack 3c. send ack 4d. send ac

50、k 4-6e. send ack 6f. send ack 7question 181refer to the exhibit. why is flash memory erased prior to upgrading the ios image from the tftp server?a. the router cannot verify that the cisco ios image currently in flash is validb. flash memory on cisco routers can contain only a single ios image.c. er

51、asing current flash content is requested during the copy dialog.d. in order for the router to use the new image as the default, it must be the only ios image in flash.question 182refer to the exhibit. what is the meaning of the term dynamic as displayed in the output of the showframe-relay map comma

52、nd shown?a. the serial0/0 interface is passing traffic.b. the dlci 100 was dynamically allocated by the router.c. the serial0/0 interface acquired by the ip address of from a dhcp server.d. the dlci 100 will be dynamically changed as required to adapt to changes in the frame relay cloud.e

53、. the mapping between dlci 100 and the end station ip address was learned through inversearp.question 183what can be done to secure the virtual terminal interfaces on a router? (choose two.)a. administratively shut down the interface.b. physically secure the interface.c. create an access

54、list and apply it to the virtual terminal interfaces with the access-group command.d. configure a virtual terminal password and login process.e. enter an access list and apply it to the virtual terminal interfaces using the access-class command.question 184refer to the exhibit. in this vlsm addressi

55、ng scheme, what summary address would be sent from router a?a. /16b. /20c. /24d. /16e. /17f. /16question 185refer to the exhibit. the show vtp status command is executed at a switch that is generating the exhibitoutput. which statemen

56、t is true for this switch?a. the switch forwards its vlan database to other switches in the icnd vtp domain.b. the configuration revision number increments each time the vlan database is updated.c. the switch forwards vtp updates that are sent by other switches in the icnd domain.d. the vlan databas

57、e is updated when vtp information is received from other switches.a. the switch forwards its vlan database to other switches in the icnd vtp domain.b. the configuration revision number increments each time the vlan database is updated.c. the switch forwards vtp updates that are sent by other switches in the icnd domain.d. the vlan d