七彩燈0807快閃0807RGB自閃快閃

1、承認書Specification for approval客戶名稱:CUSTOMER NAME: 經辦者: 職稱:DIRECTOR: TITLE: 客戶料號:CUSTOMER PART NO.: 品名: 版本: PART NUMBER: 0807快閃 REVISION: 新 發件日期: 回文日期: ISSUE DATE: 2014/01/04 RETURN DATE: / / 一、謹致執事者：茲提供敝公司產品之有關詳細規格及圖面數據，敬請給予辦理測試認定手續。同時敬請送返一份附有貴公司簽認之測試認定后之樣品認定書。 We are please in sending you herewith o

2、ur specification and drawings for your approval. Please return to us one copy “For Approval” with your approved signatures.二、附件: ACCESSORY：樣品 出貨檢驗記錄表 封裝尺寸圖 電氣特性曲線內部線路圖 焊性建議 PAD建議 包裝方式 三、客戶意見欄 CUSTOMERS PROPOSALAGREE 同意 (請于認可欄中簽名)DISAGREE 不同意 REASON 原因: 客戶認可簽章: CUSTOMER SIGNATURE: FEATURES 功能敘述 l 本產品

3、為一顆3 種顏色(RGB)七彩效果 閃爍的 LED。閃爍方式分多段: 單燈漸明漸暗漸亮漸暗單閃雙閃等。 l 正輸出，上電長閃。 l 閃爍周期約為 12 秒。 l APPLICATION 產品應用 用于裝飾、禮品之三色閃燈等。 ELECTRICAL CHARACTERISTICS 電氣規格 ( VDD=3V , TA=25 unless otherwise specified ) Characteristic Symbol Min. Typ. Max. Unit Remarks 工作電壓 Operating Voltage VDD 2.0 3.0 4.5 V 工作電流 Operating Cur

4、rent IDD - 0.1 0.2 mA No load 推動電流 Driving Current IOL - 25 - mA VDS=1.0V 工作溫度 Operating Temperature Temp. 0 25 60 Product size 產品尺寸規格Recommended Soldering Pattern（推薦的焊接模式） (Units : mm) Tape Specifications(Units : mm)Remarks:If special sorting is required (e.g. binning based on forward voltage, lumi

5、nous intensity / luminous flux or wavelength),the typical accuracy of the sorting process is as follows:1. Wavelength: +/-1nm2. Luminous Intensity / Luminous Flux: +/-15%3. Forward Voltage: +/-0.1VNote: Accuracy may depend on the sorting parameters.Suggest welding way 此型號不能串聯使用，否則會出現閃爍混亂Reliability

6、Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition Test Hours/Cycles Sample Size Ac/Re1 Reflow Soldering Temp. : 260±5 Min. 5sec. 6 Min. 22 PCS.0/1 2 Temperature Cycle H : +100 15min 5 min L :

7、-40 15min 300 Cycles 22 PCS.0/1 3 Thermal Shock H : +100 5min 10 sec L : -10 5min 300 Cycles 22 PCS.0/1 4 High Temperature Storage Temp. : 100 1000 Hrs. 22 PCS.0/1 5 Low Temperature Storage Temp. : -40 1000 Hrs. 22 PCS.0/1 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS.0/1 7 High Temperature / High

8、 Humidity 85/ 85%RH 1000 Hrs. 22 PCS.0/1 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use.

9、2.2 Before opening the package: The LEDs should be kept at 30 or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30 deg C or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent m

10、aterial (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more t

11、han two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unav