ocss常規參數設置

1、奧的斯電梯OCSS常規參數設置 2008-12-25 10:37:54  作者：  來源：互聯網   · 奧的斯電梯OCSS常規參數設置 1-14FIELD20Field Engineering Spare 2Reserved for Field Engineering patches.Please report all patches to OECF, so that Software Configuration Management integrity can be maintained.1-15FIELD30Field

2、 Engineering Spare 3Reserved for Field Engineering patches.Please report all patches to OECF, so that Software Configuration Management integrity can be maintained.1-16FIELD40Field Engineering Spare 4No.SymbolInitial初始Setting設置Purpose and RangeGroup 1: General OCSS常規設置1-1RCB-NO1Car Identifier轎廂標識1 t

3、o 8 = car A to H群控中的轎廂標識(序號)1-2EN-CON0Enable Contract Software合同軟件授權0 = disable contract software禁止1 = enable contract software激活Determines if the contract software, contained in the contract EPROM chips, should be executed.1-3EN-EMO0Enable Overlay Controller Functionality(啟用覆蓋控制柜功能性)0 = disable ove

4、rlay controller functionality1 = enable overlay controller functionalityThis parameter should be enabled when the OCSS resides on an EMO or TEMO.Once a full MOD controller is in place; for example, an E411M or E311M controller, this parameter should be disabled.(到OCSS處于EMO或者TEMO時

5、，應將此參數置一。一個完整的MOD控制柜使用時，比如，一個E411M或者E311M的控制柜時，此參數應該被取消)1-4SVT-PO1Service Tool Position Offset服務器位置偏移0 = service tool positions start at landing 0(服務器位置從樓層0開始)1 = service tool positions start at landing 1(從樓層1開始)Specifies whether positions are displayed on the Service Tool starting at landing 0 

6、;or landing 1.(指定服務器上的位置顯示是以1還是以0開始)1-5#RINGS1Number Of Rings Used For Communication1 = Use one ring for most communication to save CPU使用一個環形通訊2 = Use two rings for all communication使用二個環形通訊This variable specifies the number of rings to be used by the OCSS to communicate with each other.(此變量指定O

7、CSS用來彼此通訊的環數)1-6R-BAUD192Ring Communications Baud Rate環行通訊比特率96 = 9600 baud192 = 19200 baudDefines baud rate used for ring communications.Note that all the cars in the group must have the same ring communications baud rate.Also note that the controller power must be cycled for the change to take aff

8、ect.(定義環行通訊的比特率。注意：群組中所有的轎廂必須擁有同樣的比特率。同時，要使改變生效，控制柜電源必須生效)1-7EMS-OPL*00000000EMS Options (EMS選項)P bit = 0: disable EMS parameter passing(禁止EMS參數通過)P bit = 1: enable EMS parameter passing(使EMS參數通過)L bit = 0: transmit OCSS load states using ICD 4.1 or lower(用ICD4.1或者更低的版本傳輸OCSS負載狀態)L bit = 1

9、: transmit OCSS load states using ICD 4.2 or higher(用ICD4.2或者更高的版本傳輸OCSS負載狀態)Systems with EMS v2.0 or lower must have parameter passing disabled.Systems with an EMS configured as ICD 4.1 or lower must have the L bit set to 0.(EMS v2.0或者更低版本的系統必須禁止參數通過，配置ICD 4.1或者更低版本的EM

10、S的系統必須使L位設定為0)1-8RSLCFG0RSL Configuration for E335M(E335M的RSL配置)0 =Car I/O read from car link, Hall I/O read from hall link, Group I/O read from group link.1 =Car I/O read from car link, Hall I/O read from car link, Group I/O read from group link.2 =Car I/O read from car link, Hall I/O read from car

11、 link, Group I/O read from car link.3 =Car I/O read from car link, Hall I/O read from hall link, Group I/O read from car link.定義： 由E335M系統形成何種環行通訊鏈Defines how the RSL links are configured for E335M systems.1-9SB-DLY30Stuck Button Processing Delay按鈕延遲處理0 to 255= process a stuck button every 0 to 255

12、secondsProcesses a stuck button periodically, so that the button will be serviced occasionally.(周期性地處理一個按紐，使它被經常性地操作)1-10CB-TYP0Car Button Type轎廂按鈕類型0 = default缺省、默認1 = mechanical機械的2 = touch tube電子觸摸Defines the type of car button mechanism.(定義轎廂按紐機械類型)1-11HB-TYP0Hall Button Type大廳按鈕類型0 = default1 =

13、 mechanical2 = touch tubeDefines the type of hall button mechanism.(定義大廳按紐機械類型)1-12CPU-T10Free CPU Time Reading IntervalCPU讀取時間間隔1 to 255 = 1 to 255 secondsDefines the interval over which minimum free CPU measurements are taken.This is for engineering use only - do not change.(定義測量空閑CPU的最小間隔，這僅作為工程使

14、用，不要改變)1-13FIELD10Field Engineering Spare 1(現場工程備用功能1)Reserved for Field Engineering patches.Reserved for Field Engineering patches.Please report all patches to OECF, so that Software Configuration Management integrity can be maintained.1-17FIELD50Field Engineering Spare 5Reserved for Field Engineering patches.Please report all patches to OECF, so that Software Configuration Management integrity can be maintained.1-18FIELD60Field Engineering Spare 6Reserved for Field Engineering patches.