模具畢業論文剃須刀蓋塑料模具的設計_第1頁
模具畢業論文剃須刀蓋塑料模具的設計_第2頁
模具畢業論文剃須刀蓋塑料模具的設計_第3頁
模具畢業論文剃須刀蓋塑料模具的設計_第4頁
模具畢業論文剃須刀蓋塑料模具的設計_第5頁
已閱讀5頁,還剩12頁未讀, 繼續免費閱讀

下載本文檔

版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領

文檔簡介

1、摘 要時代的變化,社會的進步,人們對物質的需求越來越高,模具的地位在當今社會越來越重要。所以我這次的畢業設計就選擇了設計一副模具,希望通過這次的設計能夠使我的理論知識得到檢驗和實踐。本論文是剃須刀蓋塑料模具的設計,采用ABS材料進行對模具的零件結構工藝分析的過程。在選擇注塑機的時候要考慮模具的型腔數量和最大注射量以及注射壓力等。利用UG、AutoCAD繪圖軟件繪制出模具的裝配圖和零件圖。并利用UG對模具的仿真加工,制定相應加工工藝的過程。關鍵詞:剃須刀后蓋; UG;點澆口; ABS;注塑模具;目 錄 引言1一、塑件成型工藝性分析2(一)塑件(剃須刀后蓋)分析21.塑件結構分析22.成型工藝分析

2、如下2(二)ABS 的成型過程、工藝的參數31.注射成型過程32.ABS 的注射工藝參數33.ABS 化學和物理特性3(三)注塑模工藝條件3二、擬定模具結構形式4(一)分型面的選擇41.分型面的選擇原則42.分型面的確定4(二) 型腔數目的確定5三、注塑機型號的確定5(一)所需注射量的計算5(二)選擇注射機5四、澆注系統設計6(一)主流道的設計61.主流道設計要點62.主流道澆口套的形式6(二) 分流道的布置形式61.分流道的長度62.分流道的形狀、尺寸63.分流道的表面粗糙度6(三)澆口的設計71.澆口類型及位置的確定72.澆口結構尺寸的經驗計算7五、成型零件的結構設計、計算7(一)成型零件

3、的結構設計7(二)工作尺寸的校核81.型腔尺寸8型腔徑向尺寸8型腔深度尺寸82.型芯尺寸8六、模架確定、標準件選用9七、脫模推出機構的設計10(一) 推出機構的設計原則:10(二)脫模機構的結構設計10八、設計側向的抽芯機構10(一)斜頂?shù)脑O(shè)計10(二)抽芯距的確定10九、排氣系統的設定11十、冷卻系統設計12 總 結13 參考文獻14 致 謝15§ 引 言目前,我國的經濟在經濟全球化下得到了高速發展。這樣一來為中國的模具產業提供了具有良好的條件和機遇。不但國內的模具市場在市場經濟中所占的份額越來越多,而且有許多的國外公司向國內的模具制造企業采購。因此,展望未來,在良好的市場環境下我

4、國的模具產業會逐步邁進模具制造強國的行列。然而在國民經濟的快速發展下,國內的模具產量達到了一定的規模,但發展重點沒有放在模具產品水平上。致使我國的模具在模具的精度要求和結構以及壽命上遠遠地低于國際水平。不但如此模具標準件的種類以及水平對整個模具行業的發展有重大影響。所以要不斷地提高標準件水平,才能不斷地提高我國模具的總體水平。綜合看來提高模具工業水平是在國民經濟發展中占有至關重要的地位。§ 一、塑件成型工藝性分析§ (一)塑件(剃須刀后蓋)成型分析塑件的視圖如圖所示:圖1-1 xxxxx1 塑件結構分析該塑件結構較簡單,復雜程度不高。保證塑件的壁厚盡可能均勻,以此減少氣泡、

5、縮孔等不良現象。又因?yàn)樯a(chǎn)批量不是很多,還要保證生產成本低,所以考慮材料為ABS。塑件的表面不允許有明顯的熔接痕、飛邊等工藝痕跡,要求表面光滑,對模具表面進行拋光處理。2成型工藝分析如下(1)精度等級有許多影響塑件精度因素,塑料的收縮率、注塑條件、模具結構、斜度、模具的磨損等都直接影響精度。根據SJ13721978標準,ABS塑料零件的精度分八個等級。查詢可知,ABS塑料零件盡可能選用一般精度M5級。(2)脫模斜度為了避免在塑件冷卻收縮的時候緊緊卡在型腔部分,強行取出損壞塑件的表面質量。設計塑料零件時須考慮脫模方向于內外表面,使之平行,并盡量加大脫模斜度,為了容易脫模。§ (二)AB

6、S 的成型過程、工藝的參數1注射成型過程(1)成型前的準備 對ABS 的色澤、細度和均勻度等進行檢驗。(2)塑料顆粒在注射機料筒內先進行加熱,達到熔融狀態后,填充模具再經過壓實和保持壓力不變以及回流和冷卻這五個階段完成成型過程。2. ABS 的注射工藝參數(1)注射機: 螺桿式(2)螺桿轉速(r/min): 30(3)料筒溫度() : 150170(后段)、165180(中段)、180200(前段)(4)噴嘴溫度(): 170180(5)模具溫度(): 4060(6)注射壓力(MPa): 100130(7)成型時間(s):2s注射 ; 25s保壓 ; 20s冷卻 ;成型總周期 473. ABS

7、 化學和物理特性 ABS為黃色無毒無味的不透明狀的可塑性樹脂。ABS 特性很大程度上取決于三種單體和兩相分子結構的比例,所以ABS 材料具有良好的光澤度、流動性、耐化學藥品性和電絕緣性。(三)注塑模工藝條件ABS 容易吸水,建議加工前在80的條件下進行兩個小時的干燥。熔化溫度:210280;建議溫度:245。注射速度:中高速度。ABS 塑料的主要技術指標:密度(kg/dm3) 1.021.16 抗拉屈服強度(MPa) 50,比體積(dm3/ kg) 0.860.96 拉伸彈性模量(MPa) 1.8×103,吸水率(p·c×100) 0.20.4 抗彎強度(MPa)

8、 80收縮率(%) 0.40.8 沖擊韌度( kJ/m2) 261(無缺口)/11(缺口)熔點() 130160 硬度(HB) 9.7熱變形溫度() 90108(0.46 MPa) 83103(0.185MPa)體積電阻系數(cm) 6.9×10167§ 二、擬定模具結構形式§ (一)分型面的選擇在模具設計階段,首先要確定模具分離的位置,然后才選擇模具結構。分型面的合理設計,影響著塑件質量和工藝操作的難易程度。1分型面的選擇原則:(1)要便于塑件脫模;(2)要保證塑件的質量;(3)要防止熔料從分型面處滲出;(4)要便于氣體的排出;(5)要盡量便于加工成型零件;2分

9、型面的確定在進行該塑件模具設計時,對上述原則已經充分的考慮,同時從塑件樣圖可看出該塑件具有明顯的一個平面,再結合塑件形狀,考慮其具有抽芯機構,所以選擇采用該平面作為分型面,如圖21所示:21 分型面示意圖§ (二)型腔數目的確定根據塑件的表面精度高,和模具加工以及產品的生產成本考慮,所以設定一模兩腔。§ 三、注塑機型號的確定§ 所需注射量的計算1塑件質量、體積計算通過UG 建模查詢可知一個塑件的體積V13.166CM3,兩個約為6.322 CM3,按公式計算得注射量為:1.6 X 6.3CM3 = 10.08 CM3查得ABS的密度為1.06g/ CM3 。故所需

10、塑料為的質量1.06g/ CM3×10.08 CM3=10.68g2. 模具中冷凝料體積的估算本模具采用一模兩腔,并按照體積的0.6倍估算凝料體積為:V2=V1×0.6=3.166×0.6x23.799CM33. 該模具一次注射所需塑料ABS體積 V0= V1+ V2=6.965 CM3 質量 m0=V0=1.06x6.9657.4g§ (二)鎖模力的計算根據UG 建模分析,分型面上的單一投影面積A1約為1133.54 MM2,那么兩個就約為2267 MM2。根據經驗公式計算得施壓面積為:1.35 X2267 MM2 =3060.6 MM2。查資料得:在

11、ABS成型時型腔內所產生的平均壓力為34.3MPa,故所需鎖模力為:3060.6 MM2 X 34.3MPa =104.98kN 取105kN § (三)選擇注射機通過分析,根據每一生產周期的注塑量和所需壓力,查閱參考書,可選用XS-ZY-125A 臥式注塑機比較合理,其主要技術參數:額定注射 125 注射壓力 150螺桿直徑 42鎖模力 900kN注射時間 1.6s最大開合模行程 325mm模具最大厚度 350mm 模具最小厚度 220mm噴嘴圓弧半徑 12mm噴嘴孔直徑 4mm動、定模板尺寸 428mm×458mm拉桿內間距 360 mm×360mm頂出形式

12、模具兩側裝有頂桿,離中心的距離分別為240mm§ 四、澆注系統設計§ (一)主流道的設計1主流道設計要點 (1)設計圓錐形主流道,便于凝料脫離。(2)錐角度數=2°6°。內壁表面粗糙度一般為Ra=0.4。(3)設定主流道進口直徑D=8MM的半球形凹坑。(4) 主流道末端與分流道連接處采用圓角銜接。其圓角半徑r=13mm。(5) 為了減少流道內的凝料,盡量縮短主流道長度L,取值L=95mm。2主流道澆口套的形式為了避免損傷主流道的小端入口處,通常采用碳素工具鋼,如T8A、T10A 等。本模具材料采用T8A,熱處理硬度為50HRC55HRC,如圖4-1示:4

13、-1澆口套示意圖§ (二)分流道的布置形式本模具采用一模兩腔平衡式分流道的結構形式,使塑料熔體由中心向四周分散而出。1分流道的長度兩級分流道對稱布局。一級管道長度取值44.5mm,二級管道長度取值57mm。2分流道的形狀、尺寸一級管采用半圓形,二級管采用圓錐形。根據經驗,要保證比主流道的大端小1-2mm,本模具的一級管直徑6mm。圓錐形二極管的大端直徑取4mm,小端和澆口的大小同取1.2mm。3分流道的表面粗糙度分流道表面粗糙度為:Ra=1.6m。§ (三)澆口的設計為了避免引起塑件的缺陷,要考慮澆口的形狀、位置和大小等。應盡可能設在澆口壁比較厚的地方。1澆口類型及位置的確

14、定由于該模具是中小型塑件的多腔模具,塑件外形為圓形,結構簡單,故采用點澆口。2澆口結構尺寸的經驗計算根據塑件的結構尺寸,本模具點澆口的進料口直徑取1.2mm,澆口長度取1.6mm。§ 五、成型零件的結構設計、計算§ (一)成型零件的結構設計1根據塑件輪廓,采用整體式凹模結構。該結構是由一塊金屬材料直接加工出來的。因?yàn)橛辛己玫膹?qiáng)度,不容易發生變形,表面光滑平整,不會又銜接的痕跡。但是加工精度要求很高,所以只適用于簡單形狀比較小的塑件。而本塑件分型面設置于沒有突出的光滑頂面,凹模深度比較淺且形狀簡單的小型模具。故可采用整體凹模結構,如5-1 圖示。5-1凹模結構圖2因?yàn)樵撍芗?/p>

15、內部形狀也簡單,所以采用整體式凸模,如圖5-2所示。5-2凸模示意圖§ (二)工作尺寸的校核經查詢知:ABS塑料的收縮率為0.3%0.8%。平均收縮率 S=(0.4%+0.8%)/2=0.6%模具的制造公差取 查塑料模塑成型技術書 國家標準模塑件公差數值表310,由樣件知該塑件取公差等級為MT5級。1型腔尺寸型腔徑向尺寸D1(max) =(D1+ D1Scp% 3/4)+0=(38+38*0.0063*0.32/4)+00.18mm=37.98+0018mm型腔深度尺寸H1 (max)= (H+H Scp% 2/3) +0 = (10+10×0.0062×0.2/

16、3) +0006mm=9.93 +00.06 mm 2型芯尺寸型芯徑向尺寸 d1(min)= (d1+d1Scp%+3/4)0 = (36+36×0.006+3×0.32/4) 0-0.18mm=36.430-0.18 mm 型芯深度尺寸h2(min) = (h2+ h2Scp%+2/3) 0 = (8+8×0.006+2×0.2/3) 00.06mm=8.1700.06mm § 六、模架確定、標準件選擇由前型腔的布局以及相互的位置大小,然后根據成型部件的尺寸與標準模架相結合,選用結構形式為A1-2730-Z2.的標準模架,即可滿足要求。

17、67; (一)定模座板(350mmx300mm、厚30mm)材料選用45鋼。§ (二)定模板(型腔固定板)(3000mmx300mm 厚60mm)用于固定型腔部分。一般選擇45 鋼,調質230HB270HB。§ (三)動模型芯固定板(300mmx300mm 厚70mm)一般材料選用45 鋼,進行回火和淬火。§ (四)墊塊(300mmx58mm 厚度90mm)1主要作用:適應注射機的模具安裝厚度。2結構形式:該模具采用的墊塊是平行的。3墊塊材料: 該模具墊塊采用Q235A 制造。也可用HT200、球墨鑄鐵等。4支承板(300mmx300mm 厚45mm)作用是防止凸

18、模、凹模、導柱、導套等零件脫出。5墊塊的高度h 校核h =h1 +h2 +h3 +s=0+25+20+45=90MM, 符合要求。式中 h1頂出板限位釘?shù)母叨?,因?yàn)楸驹O(shè)計未采用,故其值為0;h2推板的厚度,為25 mm;h3推桿固定板厚度,為20mm;s推出行程,為45mm;6推板(300mmx120mm、厚25mm),材料為45 鋼。7推板固定板(300mmx120mm、厚20mm),材料為45 鋼。§ 七、脫模推出機構的設計§ (一)推出機構的設計原則:(1) 應盡量設置在動模一側。(2) 機構簡單,推出動作可靠。 (3) 使脫模后的制品有良好的外觀。(4) 合模時能準

19、確復位。§ (二)脫模機構的結構設計由該塑件的外形特征及內部型芯的情況,設置脫模機構為標準推桿及利用斜頂頂出。如圖7-1所示:7-1結構示意圖§ 八、設計側向的抽芯機構根據設計要求采用斜頂頂出。§ (一)斜頂?shù)脑O(shè)計斜頂結構簡單,制造方便,穩定性好,普遍用于內抽心距較小的模具。§ (二)抽芯距的確定抽芯距應大于制品凸臺高度2mm。設凸臺高度為h,因此S=h(13)mm=22=4mm分析產品,根據查詢得斜頂斜角5度。§ 九、排氣系統的設定在成型過程中,除了有空氣外還有在成型時產生的低揮發氣體存在于模具型腔中。如果不能將這些氣體排出模具外會在內部產生

20、很大的壓力,阻礙塑料熔體的快速填充。同時在高壓下,氣體壓縮產生高溫,可能會燒焦損傷塑件。甚至氣體在一定的壓縮下會滲入塑件內部,導致產品有氣孔、疏松等缺陷。通常一般的模具是靠分型面的間隙排出氣體,很少開設排氣槽。而一般在凹模的分型面上開設排氣槽,尺寸一為寬1.56mm,深0.020.05mm,要小于塑料的溢料間隙規格,避免熔料從排氣槽溢出。根據本設計結構,利用分型面之間的間隙自然排氣就可以了,不需要開設排氣槽。§ 十、 冷卻系統設計模具的溫度過高會直接影響塑件的成型收縮,容易導致塑件脫模時變形,甚至還容易造成熔料溢出和粘在模具上。而溫度過低時,將導致熔體流動性變差,從而使塑料零件的輪廓

21、不清晰,表面有明顯的缺陷,例如銀絲和流紋狀。本設計塑件材料為ABS,流動性好,要求模具溫度(一般低于80)較低,只需要調節水的流量就可以對模具進行冷卻。§ (一)冷卻系統的設計原則:(1) 盡可能地增大冷卻管直徑和增加冷卻管數量;(2) 冷卻通道的布置應合理;(3) 結構應便于清理、加工;§ (二)冷卻管道直徑d查模具設計基礎及模具CAD表9-4知,為了使冷卻水在冷卻管內處于急流狀態,取d=8mm,布局如圖10-1所示:10-1冷卻系統布局圖請您刪除一下內容,O(_)O謝謝!Many people have the same mixed feelings when plan

22、ning a trip during Golden Week. With heaps of time, the seven-day Chinese請您刪除一下內容,O(_)O謝謝!National Day holiday could be the best occasion to enjoy a destination. However, it can also be the easiest way to ruin how you feel about a place and you may become more fatigued after the holiday, due to batt

23、ling the large crowds. During peak season, a dream about a place can turn to nightmare without careful planning, especially if you travel with children and older people. As most Chinese people will take the holiday to visit domestic tourist destinations, crowds and busy traffic are inevitable at mos

24、t places. Also to be expected are increasing transport and accommodation prices, with the possibility that there will be no rooms available. It is also common that you' ll wait in the line for one hour to get a ticket, and another two hours at the site, to only see a tiny bit of the pl

25、ace due to the crowds. Last year, 428 million tourists traveled in China over the week-long holiday in October. Traveling during this period is a matter that needs thorough preparation. If you are short on time to plan the upcoming "Golden Week" it may not be a bad idea to avoid some of th

26、e most crowded places for now. There is always a place so fascinating that everyone yearns for. Arxan is a place like this. The beauty of Arxan is everlasting regardless of the changing of four seasons. Bestowed by nature, its spectacular seasonal landscape and mountains are just beyond word. Arxan

27、is a crucial destination for the recommended travelling route, "China Inner Mongolia Arxan Hailar Manzhouli". It is also the joint of the four prairies across the Sino-Mongolian border, where people gravitate towards the exotic atmosphere mixed with Chinese, Russian, and Mongolia elements.

28、 As a historic site for the Yitian Battle, Arxan still embodies the spirit of Genghis Khan. Walking into Arxan, you will be amazed by a kaleidoscope of gorgeous colors all the year round - the Spring azaleas blooming red in the snow, the Summer sea wavering blue in the breeze, the Autumn leaves pain

29、ted in yellow covering volcanic traces, and the Winter woods shining white on the vast alpine snowscape. Hinggan League Arxan city is situated in the far eastern area of Inner Mongolia Autonomous Region. Its full name "Haren Arxan" means "hot holy water" in the Mongolian language

30、. Arxan is a tourism city in the northern frontier with a blend of large forest, grand prairies, vast snowfield, heaven lake cluster, thermium, as well as volcanic cluster. It is a rare and unique ecotourism base filled with healthy sunshine, clean air and unspoiled green.  Nestled close to the

31、 country's largest virgin forest, and known for its spring and ecological environment, Arxan is marveled at by many tourists as the purest land on earth.  You cannot miss out the Autumn of Arxan. It is definitely the best with brightly-colored scenery full of emotions.  Autumn in the n

32、orthern part of the country comes earlier than the South. A September rain followed by the footprints of Autumn brings more colors to the once emerald green mountain and blooming grassland.  Shutterbugs flock to see for themselves the marvel of splendid colors around the mountains and waters, m

33、any of whom have travel a long distance and even camp here only to capture a moment of the nature wonder.  The silver birch turns golden, while the larch is still proudly green. You will find yourself drowned in the intoxicating red of the wild fruits as well as the glamour of flowers in full b

34、lown. And your heart will be lingering on the woods as it's time for the wild fruits to ripe. The picturesque Arxan in Autumn is indeed a fairyland only exists in a dream that satisfies all your fantasies. If it rains heavily on Saturday night, some elderly Chinese will say it is because Zh

35、inu, or the Weaving Maid, is crying on the day she met her husband Niulang, or the Cowherd, on the Milky Way. Most Chinese remember being told this romantic tragedy when they were children on Qixi, or the Seventh Night Festival, which falls on the seventh day of the seventh lunar month, which is usu

36、ally in early August. This year it falls on Saturday, August 2. Folklore Story As the story goes, once there was a cowherd, Niulang, who lived with his elder brother and sister-in-law. But she disliked and abused him, and the boy was forced to leave home with only an old cow for company. The cow, ho

37、wever, was a former god who had violated imperial rules and was sent to earth in bovine form. One day the cow led Niulang to a lake where fairies took a bath on earth. Among them was Zhinu, the most beautiful fairy and a skilled seamstress. The two fell in love at first sight and were soon married.

38、They had a son and daughter and their happy life was held up as an example for hundreds of years in China. Yet in the eyes of the Jade Emperor, the Supreme Deity in Taoism, marriage between a mortal and fairy was strictly forbidden. He ordered the heaven troop to catch Zhinu back. Niulang grew despe

39、rate when he discovered Zhinu had been taken back to heaven. Driven by Niulang's misery, the cow told him to turn its hide into a pair of shoes after it died. The magic shoes whisked Niulang, who carried his two children in baskets strung from a shoulder pole, off on a chase after the empress. T

40、he pursuit enraged the empress, who took her hairpin and slashed it across the sky creating the Milky Way which separated husband from wife. But all was not lost as magpies, moved by their love and devotion, formed a bridge across the Milky Way to reunite the family. Even the Jade Emperor was touche

41、d, and allowed Niulang and Zhinu to meet once a year on the seventh night of the seventh month. This is how Qixi came to be. The festival can be traced back to the Han Dynasty (206 BC-AD 220). Traditionally, people would look up at the sky and find a bright star in the constellation Aquila as well a

42、s the star Vega, which are identified as Niulang and Zhinu. The two stars shine on opposite sides of the Milky Way. Customs In bygone days, Qixi was not only a special day for lovers, but also for girls. It is also known as the "Begging for Skills Festival" or "Daughters' Festival." In this day, girls will throw a sewing need

溫馨提示

  • 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
  • 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
  • 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
  • 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
  • 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
  • 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
  • 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

最新文檔

評論

0/150

提交評論