模板-耳機咪頭規格書4015和常見參數

1、 MICROPHONE SPECIFICATIONSPECIFICATION咪頭規格書ELECTRET CONDENSER MICROPHONE型號：MODEL：4015L8-423-C1033一、 主要技術特性 Specifications1、靈敏度 Sensitivity: -423dB(0dB=1V/Pa,1KHz)2、指向性 Directivity: Omni-directional3、輸出阻抗 Output Impedance: 2.2K30% at 1KHz4、標準工作電壓 Standard Operating Voltage: 2V5、工作電壓 Operating Voltage

2、: 1.1V10V6、工作電流 Current Consumption: 350A7、信噪比 S/N Ratio: 60dB8、最大音壓輸入 Max Input Sound Level 115dB S.P.L9、頻響曲線 Frequency Response Curve10、電路示意圖 Schematic Circuit (Vs=4.5V RL=2.2K)10P 33P二、 機械性能 Mechanical Characteristics1.重 量 Weight : 0.3g2.外形尺寸 Dimensions: (Unit: mm)PartMin.StandardMax.REMARKA3.9mm

3、4.0mm4.1mmB1.4mm1.5mm1.6mmC/9mm10mm11/mmD/0.4mm0.5mm/0.6mmE/F0.1mm0.2mm0.3mmG/3.溫度 TemperatureA) 儲藏溫度范圍 Storage Temperature: -40+65B）使用溫度范圍 Operating temperature: -20+504.焊接熱沖擊 Soldering Heat Shock經過2655焊接，靈敏度變化在3dB變化范圍內。After soldering heat shock at 2655, sensitivity change within 3dB relative to i

4、nitial value.三、可靠性試驗 Reliability Test1.振動試驗 Vibration Test在振動臺上，話筒經過三個方向的振動，振幅1.52mm，振動頻率由10Hz到50Hz循環，每分鐘一次，振動2小時，其靈敏度變化在+3dB范圍內。After Vibration cycle of 10 to 50Hz/1min, for 2 hours, full Amplitude 1.52mm,in 3 directions, Sensitivity change within 3dB relative to initial value.2.跌落試驗 Dropping Test將

5、試驗話筒裝入包裝盒內，分三個不同的側面，每次從1米高度跌落在地板上，其靈敏度變化在3dB之內。With package ,dropping to concrete floor 1m height in the directions of three different edges, sensitivity change within 3dB relative to initial value.3.溫度試驗 Temperature TestA)高溫試驗 High Temperature Test將測試話筒放在+802的烘箱內，經過200小時，在20室溫內放置2小時之后測量，其靈敏度變化在3dB之

6、內。After exposure at +802 for 200 hours, and recovering in 20 for 2 hours ,sensitivity change within 3dB relative to initial value.B)低溫試驗 Low Temperature Test將試驗話筒放在-252的低溫箱內，經過200小時，在20室溫內放置2小時之后測量，其靈敏度變化在3dB之內。After exposure at-252 for 200 hours, and recovering in 20 for 2 hours, sensitivity change

7、 within 3dB relative to initial value. 4.潮濕試驗 Humidity Test將話筒放置在+602和相對濕度在905的潮濕箱內200小時，取出后防在20室溫內2小時之后測試，靈敏度變化在3dB之內。After exposure at +602 and relative humidity 905 for 200 hours, and recovering in 20 for 2 hours , sensitivity change within 3dB relative to initial value. 5.溫循試驗 Temperature Cycle

8、Test將試驗話筒放在-552的低溫箱內30分鐘，取出在室溫20內10分鐘自然恢復后，放入溫度為+852的烘箱內30分鐘，取出放在室溫20內10分鐘，此為一個溫循過程。經過5次循環，在室溫20自然恢復2小時后測試，其靈敏度變化在3dB之內。After exposure at 5 times of the following cycles, and recovering in 20 for 2 hours, Sensitivity change within 3dB relative to initial value.+20+20+852-55230m30m10m10m一個周期 one Cycl

9、e 四、 結構圖 Microphone Material TableNOPARTSMODELMANUFACTURER1線路板 PCBSuZhou SanSheng 2場效應管 FET2023電容 CapacitorMURATA4塑環 Holder SuZhou WorlD5銅環 Connecter SuZhou WorlD6振膜 MembraneDUPONT USA7墊片 SpacerWangSunZhuang HeBei8極板 PlateSuZhou WorlD9外殼 Outer most shellLansen Electronic Corp Shanghai10防塵網 Protectio

10、n fleeceChangzhou ChaoQi11連接線 WireUL1571 32#關于焊接操作Regarding the soldering operation每個駐極體傳聲器中都有一個場效應晶體管，半導體很容易在過熱電壓過高而受到損害。Each Con. Mic. contains a FET within its case. Generally, semiconductors are easily weakened by over-heating, over-charge of voltage.正常焊接的注意事項：Special caution is needed for proper soldering as follows:1.用15W-20W控溫烙鐵，溫度控制在260-280進行焊接。Use 15W-20W soldering iron and maintain 260-280 in operation.2.焊接時間在每個焊點上控制在2秒鐘以內，不允許時間過長。Soldering should be accomplished within two seconds at each terminal so as not to be overheated.3.焊接時間過長，或焊接溫度過高，不但會引起場效應管發生變化，并且話筒里面的塑料腔