84B2A-A16-J10L中文資料

1、84B2A-A16-J10L中文資料*RoHS Directive 2002/95/EC Jan 27 2003 including AnnexStandard Resistance Range.200 to 100 K ohms.1 K to 100 K ohms Total Resistance Tolerance.5 %.10 %Independent Linearity.0.25 %.0.25 %Absolute Minimum Resistance (J Taper).1.0 ohm or 0.1 % (whichever is greater).Effective Electric

2、al Angle.3600 +10 , -0 .3600 +10 , -0 Dielectric Withstanding Voltage (MIL-STD-202, Method 301)Sea Level.1,000 VAC minimum.1,000 VAC minimumInsulation Resistance (500 VDC).1,000 megohms minimum.1,000 megohms minimum Power Rating (Voltage Limited By Power Dissipation or 350 VAC, Whichever Is Less)+70

3、 C .1 watt.1 watts +125 C.0 watt.0 wattTheoretical Resolution.See table .Essentially infiniteEnd Voltage (K Taper).0.2 % of applied voltage Noise (J Taper).100 ohms ENR maximum.Output Smoothness (K Taper).0.15 % maximumEnvironmental Characteristics 1Operating Temperature Range.+1 C to +125 C.+1 C to

4、 +125 C Storage Temperature Range.-55 C to +125 C.-55 C to +125 C Temperature Coefficient Over Storage Temperature Range.50 ppm/C.100 ppm/C Vibration.15 G.15 G Total Resistance Shift.2 %.2 %Voltage Ratio Shift.0.2 %.0.2 %Wiper Bounce.0.1 millisecond maximum.0.1 millisecond maximum Shock.50 G.50 G To

5、tal Resistance Shift.2 %.2 %Voltage Ratio Shift.0.2 %.0.2 %Wiper Bounce.0.1 millisecond maximum.0.1 millisecond maximum Load Life.1,000 hours .1,000 hours Total Resistance Shift.2 % maximum.5 % maximumRotational Life (No Load).1,000,000 shaft revolutions.4,000,000 shaft revolutions Total Resistance

6、Shift.5 % maximum .5 % maximum Moisture Resistance (MIL-STD-202, Method 103, Condition B)Total Resistance Shift.2 % maximum.5 % maximumInsulation Resistance (500 VDC).100 megohms minimum.100 megohms minimum IP Rating.IP 40.IP 40Mechanical Characteristics 1Stop Strength .33.90 N-cm (48.0 oz.-in.) min

7、imum Mechanical Angle .3600 +15 , -0 TorqueStarting.Running torque plus 0.7 N-cm (1.0 oz.-in.) maximum Running (1 or 2 Section).0.18 to 1.41 N-cm (0.25 to 2.0 oz.-in.)Mounting (Torque on Bushing).1.7-2.0 N-m (15-18 lb.-in.) maximum Shaft Runout.0.15 mm (0.006 in.) T.I.R.Shaft End Play.0.36 mm (0.014

8、 in.) T.I.R.Shaft Radial Play.0.13 mm (0.005 in.) T.I.R.Weight (Single Section).21 gm (0.75 oz.)(Each Additional Section).18 gm (0.65 oz.)Terminals .Printed circuit terminals or solder lugs Soldering Condition .Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.Maximum

9、temperature 399 C (750 F) for 3 seconds. No wash process to be used with no clean fluxMarking .Manufacturers trademark, wiring diagram, date code and resistance, manufacturers part number Ganging (Multiple Section Potentiometers).2 cup maximum Hardware .One lockwasher and one mounting nut is shipped

10、 with each potentiometer, except where noted in the part number.NOTE: MODEL 83/84 PERFORMANCE SPECIFICATIONS DO NOT APPLY TO UNITS SUBJECTED TO PRINTED CIRCUIT BOARD CLEANING PROCEDURES.1AT ROOM AMBIENT: +25 C NOMINAL AND 50 % RELATIVE HUMIDITY NOMINAL, EXCEPT AS NOTED.*Ro H S C O M P L I A N T V E

11、R S I O N S A V A I L A B L EResistance Resolution (Ohms)(Nom.) (%)200.048500.0371 K .0322 K .0315 K .02310 K .02021 K .01550 K .012100 K.010Wirewound Resolution TableDual Section Model 83 PC PinsNote: The Models 83/84 dimensions for dual section assembly are for either single or dual concentric shaft styles.Dual Section Model 84 Solder LugsDimensional DrawingsMM (INCHES)83/84 - 5/8 ” Square 10-Turn83/84 - 5/8 ” Sq