Window8 WHQL and MDA (Mileston 1) SOP_20130703-v2

1、WHCK setup and MDAlogo Winner-he&Ning-ning_Dong 0 Windows HCK test process Install Controller and Studio software on the test server Install Client software on the test computer(s) MDA 2013 tool- MDALogo_v1 FQA 1 Step 1: Install Controller and Studio on the test server a. On the test server, run HCK

2、Setup.exe b. During the installation, just keep the settings by default, except for the following change. 2 Step 2: WHCK Controller Requirement Windows Management Framework (WMF) 3.0 is installed if the controller runs on Windows Server 2008 R2 SP1. If not, please download and install WMF 3.0 packag

3、e from http:/ 3 Step 3: Install Client on the test computer(s) The Client software is stored on the test server, so make sure there exists a connection between test server and test computer. Having Secure Boot enabled on a test computer might cause the client installation fail, therefore, make sure

4、to disable Secure Boot. a. On the test computer, press “win”+”R” then type HCKInstallClientSetup.exe Note: Replace with the name of the test server b. The Client setup wizard appears, then click Next to start the installation 4 During the installation, just keep the settings by default, except for t

5、he following change. 5 Share tool 此工具用批處理寫成，告別手動輸入命令。 解壓縮到腳本的目錄下運行即可。 輸入待測計算機的名字要和HCK Studio裡面顯示的保持一 致。 測多個幾臺，可以另外再運行此工具即可。 6 Mdalogo notes 確定test machine在default pool 裡 且status是Not ready 若要同時測試多臺機器,則再多開command line視窗,輸入mdalogo.cmd參數 即可 關閉第三方殺毒軟件防火墻和實時掃描功能(McAfee and NIS) （方法見P10） 設置IPv4和IPv6 addres

6、s（方法見下面）(確保client端和server端能互相Ping 通) 7 確認平臺SMBIOS的UUID值不為空或都是F(UUID值為33位）。查看方法： DOS下 用amidedos /all, 如果UUID值為空或者都是F，請用命令amidedos /su auto 會自動隨機生成UUID并刷上，每次刷過BIOS后，確認下UUID。 沒有過WHQL的驅動，則不能跑此工具, 確保所有驅動沒有yellow bang 如果藍牙是被禁用的，手動啟用。 關閉系統睡眠功能，修改所有電源計劃中的睡眠項和Monitor off 的時間都改 為Never,確保系統長時間運行不會關閉顯示器，系統不會進入睡

7、眠狀態。 確認手動進入S3后，能正常喚醒。 確認手勢軟件是Turn Off. 確認控制面板下的Devices and Printers中，沒有Multimedia Devices項，否 則移除該項。 測試結果有Fail，系統要做下reset. 8 For Paris2 l Paris2機臺在跑MDA時，建議不使用Intel G640 CPU, 這 個CPU在跑System - Sleep with IO Before and After (Certification) , Fail概率很大。 l 建議不使用Intel i7-3770S CPU, 這個CPU在跑CRASH項時Fail 概率很大。

8、 9 For Visalia and Victoria 兩種幾臺都要把無線網卡中的Power Management 中的 Allow the computer to turn off the device to save power 默認勾選項給去掉。 測試幾臺中CPU使用AVLC中的 高端CPU 10 關閉防火墻和實時掃描 11 Audit requirements 12 Windows 8 Hardware Certification Requirements: Requirement IDTest NamesTypeLength (in minutes) System.Client.Sy

9、stemPartition.DiskPartitioningSystem - Partition ValidationM2 System.Client.PCContainer.PCAppearsAsSingleObjectSingle Computer Display Object test Laptop A2 System.Fundamentals.SMBIOS.SMBIOSSpecificationSMBIOS HCTA2 System.Fundamentals.HAL.HPETRequiredHal timer tests (HCT)A5 System.Fundamentals.Sign

10、edDrivers.BootDriverEmbeddedSignature System - Embedded Signature Verification A2 System.Fundamentals.PowerManagement.PCResumesInTwoSecondsPC ResumeA10 System.Fundamentals.Graphics.DisplayRender.StableAndFunctionalCRASH - Display Stress 4-hour WDDM Profile (AMD64) A240 System.Fundamentals.SignedDriv

11、ers.DigitalSignature Signed Driver Check (CheckLogo)A5 To prevent that Client computer goes to sleep during a test A machine that is an AOAC (always on, always connected) machine but not an ARM machine can potentially go to sleep while a test is being executed. To prevent this, run the following com

12、mand from an administrator command line on each client machine: powercfg /setacvalueindex scheme_current sub_video videoidle 0 & Powercfg /setdcvalueindex scheme_current sub_video videoidle 0 & Powercfg /s scheme_current 13 How to assign IPv6 address (Server) Open Control Panel Network and Internet

13、Network Connections Right click on Local Area Connection (Ethernet) Select Internet Protocol Version 6 (TCP/IPv6) and click Properties Chose “Use the following IPv6 address” and fill in an IPv6 address and Subnet prefix length You can refer the address settings as below 14 How to assign IPv6 address

14、 (Client) Open Control Panel Network and Internet Network Connections Right click on Local Area Connection (Ethernet) Select Internet Protocol Version 6 (TCP/IPv6) and click Properties Chose “Use the following IPv6 address” and fill in an IPv6 address, Subnet prefix length, and Default gateway Defau

15、lt gateway must be servers IP address 15 WHCK QFE Updates QFE (Quick Fix Engineering) is to improve Logo Test Kit maintenance feature. Refer http:/ for QFE documentation. With each new QFE there is a new HCKSetup.exe created. Must go to Dev Center http:/ and download the new HCKSetup.exe directly. S

16、ome other key points to note in the QFE QFEs are cumulative o There is no way to pick and choose QFE updates Current QFEs are optional o In the future, some QFEs may be released that are required Applying QFEs causes previous test results to be removed! There is no support for applying a QFE in the

17、middle of a test run and then continuing 16 WHCK QFE Updates (Cont.) You can compare your current version against QFE version listed on the QFE update site by checking in: Control Panel Programs and Features To update with the latest QFEs: 1. Run HCKSetup.exe download from http:/ 2. From the pop-up

18、dialog, do not chose the “install” option. Instead, select the “Download” option 3. Run the downloaded file to the target machine 17 WHCK Filters Errata: When Microsoft discovers a problem in either a WHCK test or in the operating system itself that causes certification tests to fail incorrectly, er

19、rata is created to allow partners to pass the problematic test. Errata uses filters to automatically filter the failure from the submission results. Download filters from http:/ 1. Open the downloaded HCKFilterUpdates.cab file 2. Click and drag UpdateFilters.sql from the zip file to your desktop 3.

20、Click and drag the UpdateFilters.sql file from your desktop to the %Program Files (x86)%Windows Kits8.0Hardware Certification KitController directory 4. From that directory, run the UpdateFilters.exe command 18 Running MDALogo.cmd Copy the two automations scripts, mdalogo.cmd and mdalogo.ps1, to a l

21、ocal folder on WHCK controller, such as C:MDAAudit, which is assumed below. To start test on the HCK Controller, open a prompt window. In the new command window: Type “cd C:MDAAudit” in the CMD window to get to C:MDAAudit prompt Type the command as follows into the command prompt: mdalogo.cmd m *Rep

22、lace with the name of MDA audit system. The tool will run and show progress. When test is completed, it will show a summary of the tests on the screen as well as where the results are saved. After the tool shows the summary of the tests on the HCK Controller screen, open the C:MDAAuditPackages folde

23、r There is a text file called “MDAAudit_” followed by the name of the audit machine which is a summary of the test results. The detailed test results can be viewed by opening MDAAudit_ .hckx using HCK Studio Go to the Results tab in the HCK Studio and open the Signed Driver Check file for a list of

24、unsigned drivers. Alternatively, for Windows 7 MDA Systems, the tester may use checklogo7.exe to test for signed drivers. Tester will run checklogo7.exe, and will then open the file called “chklogo7_faileddrivers” for a list of unsigned drivers. For Windows 8 MDA Systems, the tester will look for the Windows 8 certification test failures listed separately in the applicable file. 19 WHCK Filters (Cont.) Apply filters when you want to check t