課件有限元分析例子

1、三、用ANSYS 構建一個機械連桿模型圖（如圖（A）所示），并用圖（B）兩個圓進行網格細化，模型的具體尺寸如圖（C）所示。網格進行分網（參考圖（A）機械連桿模型圖圖（B）機械連桿模型網格圖圖（C）機械兩桿模型尺寸圖APDL 程序：/PREP7 K,-1.8K,-1.8,0.35K,-1.4,0.35L,L, CSYS,1 K,1.4,135K,1,180K,1,135 L,L,1,2,233,5,460.350.550.45LFILLT,2,3,0.25, , wpro,-45.000000, CSYS,4 LSYMM,Y,all, , , ,0,0 wpro,45.000000, LSYMM

2、,X,all, , , ,0,0 WPOFF,6.5CSYS,4wpstyle,0.05,0.1,-1,1,0.003,1,2,5 K,0.7K,0.7,135K,0.4K,0.4,90L,L,26,27,2528wpstyle,0.05,0.1,-1,1,0.003,0,2,5 LSYMM,X,18, , , ,0,0CSYS,0 K,2.5,0.55K,5.2,0.45 FLST,3,4,3 FITEM,3,22 FITEM,3,31 FITEM,3,32 FITEM,3,26 BSPLIN, ,P51X LSYMM,Y,all, , , ,0,0allselNUMMRG,ALL, , ,

3、 ,LOW FLST,2,28,4FITEM,2,8 FITEM,2,7 FITEM,2,10 FITEM,2,6 FITEM,2,12 FITEM,2,13 FITEM,2,16 FITEM,2,14 FITEM,2,20 FITEM,2,17 FITEM,2,37 FITEM,2,40 FITEM,2,34 FITEM,2,33 FITEM,2,32 FITEM,2,36 FITEM,2,26 FITEM,2,27 FITEM,2,23 FITEM,2,28 FITEM,2,2 FITEM,2,22 FITEM,2,25 FITEM,2,21 FITEM,2,1 FITEM,2,30 FI

4、TEM,2,5 FITEM,2,3 AL,P51X FLST,2,8,4FITEM,2,4 FITEM,2,9 FITEM,2,15 FITEM,2,11 FITEM,2,24 FITEM,2,29 FITEM,2,31 FITEM,2,35 AL,P51X FLST,2,4,4 FITEM,2,19 FITEM,2,39 FITEM,2,18 FITEM,2,38 AL,P51X FLST,2,1,5,ORDE,1 FITEM,2,1 FLST,3,2,5,ORDE,2 FITEM,3,2 FITEM,3,-3ASBA,P51X,P51X, , ,ET,1,PLANE42 MPTEMP, M

5、PTEMP,1,0 MPDATA,EX,1,4e5 MPDATA,PRXY,1,0.3MSH,0,2DMSHKEY,0CM,_Y,AREA ASEL, , , , CM,_Y1,AREA CHKMSH,AREA CMSEL,S,_Y AMESH,_Y1 CMDELE,_Y CMDELE,_Y1 CMDELE,_Y24FLST,5,12,4,ORDE,12 FITEM,5,4FITEM,5,9 FITEM,5,11 FITEM,5,15 FITEM,5,18 FITEM,5,-19 FITEM,5,24 FITEM,5,29 FITEM,5,31 FITEM,5,35 FITEM,5,38 FITEM,5,-39 CM,_Y,LINE LS