起重機械 鋼絲繩用套環

42規范性引用文件GB/T699-2015優質碳素結GB/T700-2006碳素結構鋼GB/T6974.1起重機術語第1部分GB/T9440-2010可鍛鑄鐵件GB/T13384機電產品包裝通用技術條件GB/T16825.1金屬材料靜力單軸試驗機的檢驗與校準第1部分：拉力和(或)壓力試驗機GB/T17107-1997鍛件用結構鋼牌號和力GB/T37400.14重型機械通用技術條件第14部分：鑄鋼件GB/T37400.15重型機械通用技術條件第15部分：鍛鋼件4型式和基本參數普通套環適用抗拉強度不大于1770MPa的重型套環適用抗拉強度不大于1960MPa4.2結構型式和尺寸56套環規格(鋼絲繩公稱直徑)d/mm尺寸/mm單件質量/kgFCADGminK基本尺寸極限偏差基本尺寸極限偏差基本尺寸極限偏差基本尺寸極限偏差66.7±0.210.50-1.0+1.5027+2.703.34.20-0.10.03288.9±0.314.00-1.420+2.0036+3.604.45.60-0.20.07511.2±0.317.525455.57.00.15013.4±0.421.030546.68.40.25015.6±0.524.535637.79.80.39317.8±0.628.00-2.840+4.0072+7.208.811.20-0.40.60520.1±0.631.545819.912.60.8672022.3±0.735.0509011.014.01.2052224.5±0.838.5559912.115.41.5632426.7±0.942.00-3.460+4.80+8.6013.216.80-0.62.0452629.0±0.945.56514.318.22.6202831.2±1.049.07015.419.63.2903235.6±1.256.08017.622.44.8543640.1±1.363.00-4.490+6.00+11.3019.825.20-0.86.9724044.5±1.570.022.028.09.6244449.0±1.677.024.230.812.8084853.4±1.884.021626.433.616.5955257.9±1.991.00-5.5+7.80234+14.0028.636.40-1.120.9455662.3±2.198.025230.839.226.3106066.8±2.2105.027033.042.031.3967套環規格絲繩公稱直徑)d/mm尺寸/mm單件質量/kgFCABLRGminDE基本尺寸極限偏差基本尺寸極限偏差基本尺寸極限偏差基本尺寸極限偏差基本尺寸極限偏差88.9±0.314.00-1.420405659+306.05200.0811.2±0.317.525+0.149+0.0655070747.50.1713.4±0.421.0306084899.00.3215.6±0.524.535709810.50.5017.8±0.628.00-2.840+0.18080+6012.00.7820.1±0.631.545+0.0809013.51.142022.3±0.735.05015.010301.412224.5±0.838.55516.51.962426.7±0.942.00-3.460+9018.02.412629.0±0.945.565+0.220+0.10019.53.462831.2±1.049.07020721.04.303235.6±1.256.08022423724.06.463640.1±1.363.00-4.490252267+13027.09.774044.5±1.570.0+0.26020028029630.012.944449.0±1.677.0+0.12022030832633.0154517.024853.4±1.884.024033635636.022.755257.9±1.991.00-5.5260364385+19039.028.415662.3±2.198.0+0.305+0.14528039241542.035.566066.8±2.2105.030042044545.048.354.3標記示例88普通套環鋼重型套環 —5.2承載能力5.2.1普通套環的最大承載能力不應低于公稱抗拉強度為1770MPa的圓股鋼絲繩最小破斷拉力的5.3疲勞性能5.4表面質量不平等缺陷。套環的尖端處應自由貼合，并將尖端部位截短至凹槽深的一半。套環表面(除供需雙方另5.5無損檢測96.1.1目測檢查包括但不限于套環的尺寸測其中不合格件數不大于C1件，則該批套環即可驗收；若大于或等于C2n1/n2C/C21234567896.2承載能力試驗6.3疲勞試驗6.4.2采用鑄鋼制成的重型套環的超6.4.3采用鍛鋼制成的重型套環的超1√2√3-4√注1：?-?表示需方有要求時；8.18.2套環所用包裝形式和材料應考慮套環在運輸途中和