軸承壓裝力計算軟件

計算數據,F--壓入力（N),F=PfmaxπdfLfμ,584.1509,,0.0596,噸

設計數據,df--結合直徑（mm）,,34.9000,,,

設計數據,Lf--結合長度(mm）,,9.3980,,,

選擇數據,μ--結合面摩擦系數,,0.1300,,,

計算數據,Pfmax--結合面承受的最大單位壓力(N/mm2),,13.7000,,,

設計數據,δmax--最大過盈量（mm),,0.0127,,,

選擇參數,Ea--包容件材料彈性模量（N/mm2）,,230000.0000,,,

選擇數據,Ei--包容件材料彈性模量（N/mm2）,,230000.0000,,,

計算數據,Ca--系數,Ca=[(da2+df2)/(da2-df2)]+Va,1.3516,,,

計算數據,Ci--系數,Ci=[(df2+di2)/(df2-di2)]-Vi,4.7576,,,

設計數據,da--包容件外徑（mm）,,70.0000,,,

設計數據,di--被包容件內徑，實心軸為0（mm）,,28.5750,,,

選擇參數,Va--包容件泊松系數,,0.3100,,,

選擇參數,Vi--被包容件泊松系數,,0.3100,,,

,注：在選用壓力機規格時應是計算壓力P的3～3.5倍,,,,,

計算數據,Fend----最終壓裝力(N),,1927.6980,,0.1967,噸

,使用資料,,,,,

,58-22材料摩擦系數,,,,,

,村料,摩擦因數μ（無潤滑）,摩擦因數μ（有潤滑）,,,

,鋼一鋼,0.07~0.16,0.05~0.13,,,

,鋼—鑄鋼,0.11,0.07,,,

,鋼一結構鋼,0.1,0.08,,,

,鋼一優質結構,0.11,0.07,,,

,鋼—青銅,0.15~0.20,0.03~0.06,,,

,鋼—鑄鐵,0.12~0.15,0.05~0.10,,,

,鑄鐵—鑄鐵,0.15~0.25,0.05~0.10,,,

,表58-23，常用材料的彈性模量，泊松比和線脹系數,,,,,

,材料,彈性模量E/（KN/mm2）,泊松比v,線脹系數a/(10-6/℃,,

,,,,加熱,冷卻,

,碳鋼、低合金鋼、合金結構鋼,200~235,0.30~0.31,11,—8.5,

,灰鑄鐵（HT150、HT200）,70~80,0.24~0.25,11,—9,

,灰鑄鐵（HT250、HT300）,105~130,0.24~0.26,10,—8,

,可鍛鑄鐵,90~100,0.25,10,—8,

,非合金球墨鑄鐵,160~180,0.28~0.29,10,—8,

,青銅,85,0.35,17,—15,

,黃銅,80,0.36~0.37,18,—16,

,鋁合金,69,0.32~0.36,21,—20,

,鎂鋁合金,40,0.25~0.30,25.5,—25,

,壓裝時的主要要求為：,,,,,

,

1）壓裝時不得損傷零件,,,,,

,

2）壓入時應平穩，被壓入件應準確到位。,,,,,

,

3）壓裝的軸或套引入端應有適當導錐，但怠錐長度不得大于配合長度的15%，導向斜角一般不應大于10°。,,,,,

,

4）將實心軸壓入盲孔，應在適當部位有排氣孔或槽。,,,,,

,

5）壓裝零件的配合表面除有特殊要求外，在壓裝時應涂以清潔的潤滑劑。,,