加工中心精度檢驗規范.doc

NO. 日 沛 電 腦 配 件（上 海） 有 限 公 司 RI PEI computer accessory (Shanghai) Co., Ltd. 加工中心精度檢驗規範 機 型： MODEL 機 號： SERIAL NO. 目 錄 CATALOGUE 1.0 靜態精度檢查 . 6 頁PAGE STATIC ACCURACY INSPECION 2.0 定位精度檢查 . 1 頁PAGE POSITION ACCURACY INSPECTION 3.0 重復精度檢查 . 1 頁PAGE REPETITIONAL ACCURACY INSPECTION 4.0 循圓精度. 1 頁PAGE PALLET ACCURACY 5.0 附件 . 頁PAGE ACCESSARY 共 . 頁PAGE 中國上海松江區新橋鎮申港路3636號No.3636 Shenggang Road,Xin Qiao Songjiang Shanghai China 核準者CONFIRMED檢驗者CHECKED檢 驗日 期DATE MCV F01 S001 Q301000003 940331-71.0靜態精度STATIC ACCURACY INSPECTION 單位Unit : mm項次NO檢查項目Inspection item測 試 方 法 圖Measuring method diagram許 可 差Permissible deviation實 際測 量 值Measured value1.1床臺X 軸方向運動之真直度Straightness of the X axis movementa.X-Z面內0.06/1000b.Y-Z面內1.2床臺Y 軸方向運動之真直度Straightness of the Y axis movementa.X-Z面內0.06/1000b.Y-Z面內1-1 單位Unit : mm項次NO檢查項目Inspection item測 試 方 法 圖Measuring method diagram許 可 差Permissible deviation實 際測 量 值Measured value1.3床臺X軸方向之運動與其上面之平行度Parallelism between movement in X axis direction and table upper surfaceX 500 0.02500X 800 0.025800X 1250 0.031250X 2000 0.041.4床臺Y軸方向之運動與其上面之平行度Parallelism between movement in Y axis direction and table upper surfaceY 500 0.02500Y 800 0.025800Y 1250 0.031250Y 2000 0.041.5X軸方向運動與床臺基準溝側面之平行度Parallelism between movement in X axis direction and Side surface of table reference slot每300mm的量測距離下許可差為0.015mm0.015for a measuringlength of 3001-2單位Unit : mm項次NO檢查項目Inspection item測 試 方 法 圖Measuring method diagram許 可 差Permissible deviation實 際測 量 值Measured value1.6各軸方向相互運動之直角度Perpendicularity Between movement in X axis direction and Y axis direction and Z axis directiona.X-Y軸Place0.012/300b.X-Z軸Place0.012/300c.Y-Z軸Place0.012/3001.7主軸中心線與床臺面之直角度Perpendicularity between centerline of main spindle and table surface.旋徑每300Per3000.015 1-3單位Unit : mm項次NO檢查項目Inspection item測 試 方 法 圖Measuring method diagram許 可 差Permissible deviation實 際測 量 值Measured value1.8主軸孔內面之偏擺Run out of spindle taper hole固定端At spindle side end of test bar0.005固定端300處At 300 position0.0151.9主軸軸線與Z軸軸線運動間的平行度Parallelism between the spindle axis and the Z-axis motiona:0.015/300b:0.015/3001.10主軸在Z軸方向之移(松)動量Movement of main spindle in Z axis direction0.0051.11主軸端面之偏擺Run out of main spindle outer surface 1-40.011.12主軸外面之偏擺Run out of main spindle outer surface0.01mm1.13床檯X軸方向運動之直線度Straightness of table movement in the X axis.1.Apply a fixed indicator to the straight edge as the figure shown.2.Adjust to get reading at both ends of the straight edge.2.Move the table 300 mm in X-axis direction.3.Record the largest value difference as the measurement value.0.01/3001.14床檯Y軸方向運動之直線度Straightness of table movement in the Y axis 1-51.Apply a fixed indicator to the straight edge as the figure shown.2.Adjust to get reading at both ends of the straight edge.2.Move the table 300 mm in X-axis direction.3.Record the largest value difference as the measurement value.0.01/3001.15旋轉檯旋轉偏擺Table runout(XY)0.015mm/3001.16旋轉檯旋轉偏擺Table runout(Z)0.005mm1.17車刀角度換刀後重複定位精度Repeatability of tool angle after tool change.0.001mm1.18車刀角度停止後重複定位精度Repeatability of tool angle after tool stop.0.001mm1.20車刀加工後定位精度Repeatability of tool angle after machining part0.001mm1.21主軸振動檢測Spindle vibration detection0.6mm/s(Ref)2.0定位精度檢查 Positioning accuracy inspection 單位Unit : mm項次NO檢查項目Inspection item測 試 方 法 圖Measuring method diagram許 可 差Permissible deviation實 際測 量 值Measured value2.1直線運動之定位精度ISO230-2循環次數:2次Positioning accuracy of straight line movementByISO230-2Cycle times: Two timesXL10000.011000L20000.015L20000.02YZ 單位Unit: sec2.2回轉運動之定位精度Positioning accuracy of straight line movementByISO230-2Cycle times: Two timesC151-73.0反復精度檢查 Repetition accuracy inspection 單位Unit: sec項次NO檢查項目Inspection item測 試 方 法 圖Measuring method diagram許 可 差Permissible deviation實 際測 量 值Measured value3.1直線運動之反復定位精度ISO230-2Positioning repeatability of straight line movementByISO230-2Cycle times: Two timesX0.006YZ 單位Unit: sec3.2回轉運動之重復定位精度ISO230-2Positioning repeatability of straight line movementByISO230-2Cycle times: Two timesC 8 1-83.0反復精度檢查 Repetition accuracy inspection 單位Unit: sec項次NO檢查項目Inspection item測 試 方 法 圖Measuring method diagram許 可 差Permissible deviation實 際測 量 值Measured value3.3Max reversal value最大反沖值Position accuracy qualified to ISO 230-2X0.006YZ4.0循圓精度檢查 Repetition accuracy inspection 單位U