UG后處理變量.doc

UG后處理變量 global mom_seqnum global mom_part_name global mom_logname global mom_date global mom_spindle_speed global mom_output_file_basenameMOM_set_seq_offset mom_seqnum 100# MOM_output_literal (# TASK : $mom_part_name #)# MOM_output_literal (# Created By : $mom_logname)# MOM_output_literal (# Creation Date: $mom_date)# MOM_output_literal (#)# MOM_suppress always N MOM_output_literal G28 G91 Z0.0 MOM_output_literal M30 MOM_output_literal % MOM_output_literal (Date: $mom_date)# MOM_suppress off N MOM_output_literal (name: $mom_output_file_basename.nc ) MOM_output_literal ($mom_part_name)# MOM_output_literal O$mom_output_file_basename# MOM_set_seq_on global max_z min_z set zmax string trimright format %.4f $max_z 0 set zmin string trimright format %.4f $min_z 0 MOM_output_literal (MAXZ = $zmax , MINZ = $zmin) global mom_machine_time MOM_output_literal (Total Machine Time:format %.2f $mom_machine_time min)Tool_Name:$mom_tool_name Tool_No:$mom_tool_number $mom_operation_type global max_z min_z set zmax string trimright format %.4f $max_z 0 set zmin string trimright format %.4f $min_z 0 MOM_output_literal (MAXZ = $zmax , MINZ = $zmin) global mom_machine_time MOM_output_literal (Total Machine Time:format %.2f $mom_machine_time minglobaltoolnumglobaltoolinfoglobalmom_group_nameglobalmom_tool_nameglobalmom_tool_diameterglobalmom_tool_corner1_radiusglobalmom_stepover_percentglobalmom_stock_partglobalmom_stock_floorglobalmom_cut_level_max_depthglobalmom_cut_level_min_depthglobalmax_zglobalmin_zglobalmax_xglobalmin_xglobalmax_yglobalmin_yglobalmom_operation_nameglobalmom_machine_timeglobalmom_tool_flute_lengthglobalmom_dateglobalmom_part_nameglobalmom_lognameglobalmom_cutting_timeglobalpre_tool_nameglobalpre_machine_timeglobalpre_timeglobal mom_spindle_rpmglobal mom_feed_cut_valueglobal alex_depthglobal alex_stepoverglobal tol global mom_tool_number mom_next_tool_number global mom_coolant_status mom_coolant_mode global mom_spindle_rpm global mom_warning_info global anchor_flag global coolant_flag global first_tool global mom_tool_name global mom_tool_diameter global mom_tool_length_adjust_register global mom_tool_corner1_radius global mom_tool_flute_length global mom_work_coordinate_number global msys mom_stock_part global mom_stock_floor global mom_inside_outside_tolerances global mom_global_cut_depth global mom_stepover_distance global mom_global_cut_depth global mom_stepover_distance global mom_stepover_scallop global mom_stepover_variable_passes global mom_stepover_percent global mom_stepover_type global mom_depth_of_cut_type global mom_cut_level_max_depth global mom_depth_per_cut 后處理加速度詳解1. 找到后處理TCL文件用寫字板打開2. 找到proc PB_start_of_program 此處加入：PB_CMD_init_turbo3. 找到proc PB_CMD_kin_before_motion并且在其上面加入如下：距上一命令空兩行#=proc PB_CMD_init_turbo #=# This custom command may only be used with Post Builder 3.2.1# or later and NX2 or later.# Place this custom command with the Start of Program marker.# This custom command will activate the turbo process mode for# the 3-axis mill posts. The execution time will be about 5 to# 10 times faster than the normal process.# Special Blocks are included in any 3-axis mill post created# by Post Builder v3.2.1 and on.# The blocks being output are formatted similar to that of the# Fanuc type of controllers.# The following turbo blocks will appear in the Block section# of N/C Data Definitions in Post Builder:# linear_move_turbo# circular_move_turbo# rapid_move_turbo# sequence_number_turbo# In Post Builder, you may modify the Word parameters from# the N/C Data Defitions dialog to configure the output of that# word used within the turbo blocks. You may also modify the Format# parameters. You may not, however, edit the expression in the# words, remove or add words in any turbo block.# All rapid motion is output in a single move. Any custom # commands in the linear move, circular move, rapid move and # mom_before_motion event markers will be ignored.# global mom_kin_machine_type if $mom_kin_machine_type = 3_axis_mill uplevel #0 set mom_kin_is_turbo_output TRUE MOM_reload_kinematics 距下一命令空兩行 空兩行 空兩行 修改圓弧最大半徑在后處理器里面：后處理變批處理其實想讓你的后處理?yè)u身一變，成為批處理，也不是什么難事，我有個方法，大家可以試試，不過記得回貼，不然我會鄙視你有。1：先打開你的后處理*.TCL文件找到SET MOM_SYS_GROUP_OUTPUT 設為ON2：打開你的UG安裝目錄下NX3.0MACHRESOURCEpostprocessor下的UGPOST_BASE.TCL文件找到set grp_ptp_name $mom_output_file_basename_$group_name_lowercase$output_extn改成set grp_ptp_name $group_name_lowercase$output_extn3：找到proc mom_start_of_group下面的if $mom_sys_ptp_output = ON MOM_open_output_file $ptp_file_name 改成if $mom_sys_ptp_output = ON MOM_remove_file $ptp_file_name4:繼續找到proc mom_end_of_group下面的if $mom_sys