小型校園網的構建計算機網絡zq

1、企業網絡設計1. 課程設計目的1、增加對計算機網絡軟、硬件組成的感性認識初步學會典型局域網絡的操作、 使用技能；2、加深理解網絡分層結構概念尤其是對會話層、表示層、應用層等高層協議軟件的通信功能、實現方法，掌握網絡互連設備的使用及工作原理，掌握IP地址的配置；3、初步掌握局域網的設計技術和技巧培養開發網絡應用的獨立工作能力。2. 設計方案論證2.1設計思路2.1.1總體設計思路進行企業網絡總體設計，首先，進行對象研究和需求調查，弄清企業的性質、 任務和特點，對企業的信息化環境進行準確的描述，明確系統建設的需求和條件； 其次，在應用需求分析的基礎上，確定企業 In tra net服務類型，進而確

2、定系統建設 的具體目標，包括網絡設施、站點設置、開發應用和管理等方面的目標；第三，確 定網絡拓?fù)浣Y(jié)構和功能，根據應用需求、建設目標和學校主要建筑分布特點，進行 系統分析和設計；第四，確定技術設計的原則要求，如在技術選型、布線設計、設 備選擇、軟件配置等方面的標準和要求；第五，規劃安排企業網建設的實施步驟。2.1.2 網絡設計將網絡中心設在D座樓，支持遠程教學，可以接入互聯網，具有廣域網訪問的 安全機制和網絡管理功能。以 D座樓為中心，用光纖連接到其它建筑物，構成校園 網光纖主干。網絡結構分成三層：核心層、匯聚層、接入層。（1）終端用戶包括：A座樓有48個校園網普通用戶；B座樓有1個包含24個多

3、媒體用戶的電子閱覽室；C座樓有1個包含48個用戶的多媒體教室（性能要求高于電子閱覽室）D座樓是網絡中心(2) 支持遠程教學，可以接入互聯網，具有廣域網訪問的安全機制和網絡管理功能。(3) 各樓之間的距離為500米。由于各座樓之間的距離是 500米，而雙絞線的最遠距離是100米，所以基于對 條件要求的考慮，我們需要選擇光纖或串行線作為傳輸介質?？紤]傳輸高速率和擴 展的需求，企業網樓與樓之間采用光纖傳輸。網絡主干采用多模光纖。網絡中心到 主建筑物結點采用多模光纖連接。布線采用星形拓?fù)浣Y(jié)構，這樣當過渡到ATM時，不需要重新布線可使整個網絡保持原有的拓?fù)浣Y(jié)構。以上特點分層網絡結構可以獲 得良好的擴展性

4、，根據實際需求，整個企業網采用星型結構，由D座樓出發，延伸到ABC座樓。再從各個樓出發，以同軸電纜作為傳輸介質。由云到D座樓為A類網，由D座樓到各個樓之間為B類網，各個內部為C類網。對于整個網絡的拓?fù)浣Y(jié)構為混合型結構，以路由器為網絡中心的星型結構，各 部門以交換機為主結點的樹型結構。由于計算機與網絡技術的特殊性，網絡建設需要考慮以下一些因素：系統的先 進性、體統的穩定性、系統的可擴展性、系統的可維護性、應用系統和網絡系統的 配合度、與外界網絡的連通性、建設成本的可接受度等。2.1.3具體設計表1校園網設備選擇表樓座設備型號數量A座樓RouterRouter-PT1Switch2960-242P

5、CPC-PT4RouterRouter-PT2B座樓Switch2950T-242ServerServer-PT1PCPC-PT4C座樓RouterRouter-PT1Switch2950T-242PCPC-PT2SererServer-PT1D座樓RouterRouter-PT1CloudCloud-PT1表2設備連接表樓號設備1設備2設備之間的連線A座樓RouterRouter光纖RouterSwitch交叉雙絞線SwitchPC直通雙絞線B座樓RouterRouter光纖、串行線RouterSwitch直通雙絞線SwitchPC直通雙絞線SwitchServer直通雙絞線C座樓Route

6、rSwitch直通雙絞線SwitchPC直通雙絞線SwitchServer直通雙絞線SwitchSwitch交叉雙絞線D座樓RouterRouter光纖RouterCloud串行線表3主機IP地址及網關主機ip地址默認網關PC0192.168.32.2192.168.32.1PC1192.168.32.3192.168.32.1PC2192.168.33.2192.168.33.1PC3192.168.33.3192.168.33.1PC4192.168.1.3192.168.1.1PC5192.168.1.2192.168.1.1PC6192.168.5.3192.168.5.1PC7192

7、.168.5.2192.168.5.1PC8192.168.4.2192.168.4.1PC9192.16843192.168.4.1Serverl192.168.1.4192.168.1.1Server2192.168.4.4192.168.4.1表4主機IP地址及網關主機ip地址默認網關PC0192.168.32.2192.168.32.1PC1192.168.32.3192.168.32.1PC2192.168.33.2192.168.33.1PC3192.168.33.3192.168.33.1PC4192.168.1.3192.168.1.1PC5192.168.1.2192.168

8、.1.1PC6192.168.5.3192.168.5.1PC7192.168.5.2192.168.5.1PC8192.168.4.2192.168.4.1PC9192.168.4.3192.168.4.1Server1192.168.1.4192.168.1.1Server2192.168.4.4192.168.4.1拓?fù)鋱D如下:BkPC-PT 如PCO J, -5960ClcJd-PT2960-OTSwitchPC-PTPCS勺PC-PIPCPTPC7號摟.3 Liter-Fsuter-PT suterSPC-PT心2-4TTSwitch 2Router-1!三匕Router-PT二號棒

9、5vqtch4PC-PTQn j -*PC-PTPCST-24PC-PTPC9PC-PTPCSServer-PTSrv&r2PC-PTPC4295QT-24Switch 5圖1網絡拓?fù)鋱D2.2相關代碼路由器D座樓的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(config)#interface Serial2/0Router(c on fig-if)#%LINK-5-CHANGED: In terface Ser

10、ial2/0, cha nged state to upno shutdow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(c on fig-if)# no shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net4/ORouter(c on fig-if)# no shutdow n %LINK-5-CHANGED: In terfa

11、ce FastEthernet4/O, cha nged state to dow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Router(c on fig-if)# no shutdow n %LINK-5-CHANGED: In terface FastEthernet5/0, cha nged state to dow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#inter

12、face Serial2/0Router(c on fig-if)# no ip addressRouter(config-if)#ip address 10.0.0.2 255.0.0.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(config-if)#ip address 172.18.0.1 255.255.0.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface Fas

13、tEther net4/0Router(config-if)#ip address 172.16.0.1 255.255.0.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Router(config-if)#ip address 172.17.0.1 255.255.0.0 Router(c on fig-if)#在D座樓中設置靜態路由Routere nableRouter#c on figure termi nalEn ter con figurati on

14、comma nds, one per line. End with CNTL/Z.Router(config)#ip route 192.168.32.0 255.255.255.0 172.16.0.2Router(config)#ip route 192.168.33.0 255.255.255.0 172.16.0.2Router(config)#ip route 192.168.1.0 255.255.255.0 172.18.0.2Router(config)#ip route 192.168.4.0 255.255.255.0 172.17.0.2Router(config)#ip

15、 route 192.168.5.0 255.255.255.0 172.17.0.2 Router(c on fig)#路由器A座樓的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(c on fig)# in terface FastEther net0/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, c

16、ha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet0/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet1/0, cha nged state to up %LINEP

17、ROTO-5-UPDOWN: Line protocol on In terface FastEthernet1/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net4/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet4/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protoc

18、ol on In terface FastEthernet4/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(c on fig-if)# no shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(config-if)#ip address 192.168.32.1 255.

19、255.255.0 Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/ORouter(config-if)#ip address 192.168.33.1 255.255.255.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net4/0Router(config-if)#ip address 172.16.0.2 255.255.0.0Router

20、(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(config-if)#ip address 192.168.31.1 255.255.255.0Router(c on fig-if)#在A座樓中設置靜態路由Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(config)#ip route 192.168.1.0 2

21、55.255.255.0 172.16.0.1Router(config)#ip route 192.168.4.0 255.255.255.0 172.16.0.1Router(config)#ip route 192.168.5.0 255.255.255.0 172.16.0.1 Router(c on fig)#路由器B座樓的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(c on fig)# in ter

22、face FastEther net0/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet0/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Route

23、r(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet5/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet5/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial2/0Router(c on fig-if)# no shutdow nRouter(c

24、on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(config-if)#ip address 192.168.4.1 255.255.255.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Router(config-if)#ip address 172.17.0.2 255.255.0.0Router(c on fig-if)#Router

25、(c on fig-if)#exitRouter(config)#interface Serial2/0Router(config-if)#ip address 192.168.3.1 255.255.255.0Router(c on fig-if)#在B座樓中設置靜態路由Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(config)#ip route 192.168.5.0 255.255.255.0 192.168.

26、3.2Router(config)#ip route 192.168.32.0 255.255.255.0 172.17.0.1Router(config)#ip route 192.168.33.0 255.255.255.0 172.17.0.1Router(config)#ip route 192.168.1.0 255.255.255.0 172.17.0.1Router(c on fig)#路由器Router 6的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per

27、line. End with CNTL/Z.Router(c on fig)# in terface FastEther net0/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet0/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRout

28、er(config)#interface Serial2/0 Router(c on fig-if)#%LINK-5-CHANGED: In terface Serial2/0, cha nged state to upno shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(config-if)#ip address 192.168.5.1 255.255.255.0 Router(c on fig-if)#Router(c on fi

29、g-if)#exitRouter(config)#interface Serial2/0Router(co nfig-if)#ip address 192.168.3.2 255.255.255.0Router(c on fig-if)#在Router 6中設置靜態路由Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per line. End with CNTL/Z.Router(config)#ip route 192.168.32.0 255.255.255.0 192.168.3

30、.1Router(config)#ip route 192.168.33.0 255.255.255.0 192.168.3.1Router(config)#ip route 192.168.1.0 255.255.255.0 192.168.3.1Router(config)#ip route 192.168.4.0 255.255.255.0 192.168.3.1 Router(c on fig)#路由器C座樓的配置：Routere nableRouter#c on figure termi nalEn ter con figurati on comma nds, one per lin

31、e. End with CNTL/Z.Router(c on fig)# in terface FastEther net1/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet1/0, cha nged state to upRouter(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0 Router(c on fig-if)#%LINK-5-CHANGED: In terface Serial3/0,

32、cha nged state to upno shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(config-if)#ip address 192.168.1.1 255.255.255.0Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(config-if)#ip address 172.18.0.2 255.255

33、.0.0Router(c on fig-if)#%LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet1/0, cha nged state to upn o ip addressRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, cha nged

34、state to upRouter(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0 Router(c on fig-if)#%LINK-5-CHANGED: In terface Serial3/0, cha nged state to admi nistratively dow nshutdow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(c on

35、 fig-if)#shutdow n%LINK-5-CHANGED: In terface FastEthernet0/0, cha nged state to admi nistratively dow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(c on fig-if)#shutdow n%LINK-5-CHANGED: In terface FastEthernet1/0, cha nged state to admi nistrativ

36、ely dow n %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet1/0, chan ged state to dow n Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net5/0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net4/0Router(c on fig-if)#Ro

37、uter(c on fig-if)#exitRouter(config)#interface Serial3/0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net0/0Router(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(c on fig-if)# no shutdow n%LINK-5-CHANGED: In terface FastE

38、thernet1/0, cha nged state to up %LINEPROTO-5-UPDOWN: Line protocol on In terface FastEthernet1/0, changed state to up Router(c on fig-if)#Router(c on fig-if)#exitRouter(co nfig)#i nterface Serial3/0Router(c on fig-if)#%LINK-5-CHANGED: In terface Serial3/0, cha nged state to upno shutdow nRouter(c on fig-if)#Router(c on fig-if)#exitRouter(c on fig)# in terface FastEther net1/0Router(c on fig-if)#Router(c on fig-if)#exitRouter(config)#interface Serial3/0Router(config-if)#ip address 172.18.0.2 255.255.0.0Router(c on fig-if)#