Moshell常用指令RNC版

1、moshell常用命令rnc版1， lt/ltc1-9：load mo tree (full or partial) and build proxy table. lt stands for load mo types, ltc stands for load mo types and their children. thenumeric option in ltc is for specifying the number of levels of children to load. without the option, all levels of children are loaded.l

2、t指令是最常用的指令，進入moshell之后，首先用lt從庫中取mo,要不然你就看不到啥東西。通過在lt后面配置不同的過濾器可以有選擇的裝載mo,例如lt all是全部mo，lt iub只取包含（模糊查找）iub的mo。當mo發生變化，例如刪除，添加，修改參數。需要lt root更新一下，再用lt all等取mo。2， pr/lpr：print mo ldns and proxy ids for all or part of the mo tree currently loaded in moshell. pr 0-1000 - prints the mos with proxy id 0 t

3、o 1000pr：print rnc中定義了的mo，例如pr pluginunit可以顯示rnc中哪些槽位有單板定義。3， get/lget：read cm/fm attribute(s) from mo(s) get vc trafficdes - get traffic descriptors for all vcltp(s)get cable atten - get attenuation values for all cables (in rbs)get cell iub - view which cells are connected to which iubs (in rnc)ge

4、t !(utranrel|iub) - get all attributes from all mos except those whose rdn matches utranrel or iub從mo（管理對象）中讀取cm（配置管理）和fm（設備管理）的信息。想知道某mo的具體參數設置，用get 獲得，其中proxy可由pr結果獲得。 4， st/lst：print state of mos (operationalstate and administrativestate when applicable)。lst equip dis - view all disabled mos unde

5、r equipmentst all dis -view all disabled mos st all 1.*0 - view all mos which are unlocked and disabledst all 0 - view all mos which are locked:查看mo的工作（op）狀態和管理（adm）狀態。比如我們查k0001站的小區及其信道的狀態，可輸入lst utrancell=k0001。5， bls/lbls: lock or soft-lock mo(s). works by setting the administrativestate to 0 (ha

6、rd-lock) or 2 (soft-lock).deb/ldeb: unlock mo(s). works by setting the administrativestate to 1. bl aal2.*b40a12 - block aal2paths b40a1, b40a2 bl 001500 - block a board. same as lbl subrack=ms,slot=15,pluginunit=1$.當沒有s時，資源立即被鎖定，administrativestate變?yōu)?；當s加上時，administrativestate設成2，30秒過后再變成0。我們經常要對iu

7、blink及信令閉解，可以輸入lbl iublink=9 ，此時就把此iublink及其下面的nbapc，nbapd，nodesynch全部閉掉了。割接前閉塞不用的傳輸，以免出告警時有效。6， setm/lsetm: set an attribute value on one or several mos. set aal2pathvcctp=ga36 aal2qosavailableprofiles 15 set an attribute of type structset cell primarycpichpower 60 設置rnc下所有小區公共導頻功率為60set cell 參數 值

8、：設置小區某參數的值。m是為了在同一個事務transaction中設置多個屬性attributes。7， rset/lrset: set attribute value on a restricted attribute or change the moid of an mo. the rset command works by deleting the mo (and any mos by which it is reserved) andrecreating the mo (and its reserved mos) using the new attribute value. 例如改小區

9、名：rset utrancell=cell123 utrancellid cell4568， del/ldel: delete mo(s).rdel/lrdel：delete mo(s) together with children and reserving mos.當一個mo沒有子mo， reservedby list也是空值時才可能被刪除；如果此mo有子mo或者reservedby attribute非空時,可能需要用rdel/lrdel command 代替。eg: ldel %ms,slot=20,plug will delete the programs first then th

10、e piuproxies 22 to 46 were created by a create script (in run or trun). to undo it:del 46-229， acl/lacl: lists available mo actions. acc/lacc: execute an mo action. acl all restart - view all restart actionsacl all (restart)(eteloopback) - view all actions except restart and eteloopback acc 001400 m

11、anualrestart- same as: lacc subrack=ms,slot=14,pluginunit=1$ manualrestart acc 0 manualrestart-restart the node(rnc or rbs)lacc atmport=es-1-2-2-ima11 eteloopback-perform end-to-end loopback on vcltp mos acl列出mo可用的行為，acc執行上述操作。例如：acc sync addsyncrefresource就是增加node的一個同步源。 10， run/trun：run a command

12、file in moshell format. /emas/motester format run/trun*文件名-在moshell里運行命令文件一般使用trun，默認情況下當遇到意外時命令文件運行會中斷，當用truni時會忽略所有的處理失敗例外，但分析失敗或者ldn找不到時仍然會中斷。11， cvls/cvmk/cvms/cvset/cvrm/cvcu/cvget/cvput/cvls1：cvls顯示cv信息和cv清單。 cvmk創建cv備份 cvset設置cv啟動 cvms創建cv并設置啟動 cvrm冊除一個或多個cv cvcu 只顯示當前cv信息。12， l+/l-/l?: open/

13、close /check moshell logfiles. l+ 打開一個log文件，如果沒有給出log文件，將創建一個新log文件將操作信息保存在其中 l-關閉創建的log文件并保存。l? 檢查是否有一個log文件打開moshell支持同時打開多個log文件但只有一個是激活的，當一個log文件關閉，之前的log文件會恢復。 13， u+s/u-/u?/u!: handling of undo mode (for undo of bl/del/rdel/set commands). can be used for generation of mo scripts as well. u+ 開始

14、undo模式 u- 停止undo模式 u？檢查undo模式是否激活 u！轉換moshell命令文件到trun/emas格式，或undo log文件到命令文件。14， alatkc：print the list of active alarms.al 查看告警概述 ala 查看告警詳細清單 alt 同al，但可以看時間 alk 同al，但可以列出告警是否確認。15， lk/llk：view all mo(s) linked to an mo, and their states.查看管理對象的連接和狀態，例：lk iublink=站號16， bo/cabx/vii/inv 軟硬件相關bo:檢查rn

15、c中有的單板，打印單板概覽。cabx:查看rnc硬件信息，指示燈狀態，產品號，溫度等。cabl：看mp/bp的處理器負荷cabm：打印mp/bp ram內存使用率。inv：用mo形式顯示 hw/sw 詳細情況. 包括jvm,rru,設備sw (spm,dsp,fpga) 都會顯示出來，licensing 的功能和容量以及isl鏈路都會顯示。17， readclock/setclock:查看系統時鐘/設置系統時鐘setclock yyyy-mm-dd hh:mm:ss設置時間18， str/strt: 在一個node里，看所有或部分小區、iubs、nbap、sync、信道的狀態。 str -m

16、7,8,9 - print states only for modules 7, 8, and 9 str -i 9012 - print states only for iublink 9012 and its connected cells str -c 90121,90131 - print states only for the sites connected to cell 90121 and 90131 strt 比str 附帶對應的atmport19， sma all:查看該板所裝載程序的狀態是active或passive，判斷是主用板還是備用板的方法。（lhsh xxxx00

17、smaall登陸到該板查看程序工作狀態）。mirror stat:只對主框10,11槽gpb板有效，查看10,11板磁盤鏡象ftc狀態。more: ftc means fault toerant core only on main gpb and in charge of all the hw condition and redundant.20， uerdt: print ue context data (serving or drifting) for all active calls (rnc only). uer -i 0001 - print uecontext data for a

18、ll ues whose imsi match 0001. uer -m 8 - print uecontext data for all ues in module 8.看rnc下的用戶數量，用戶等級，以及用戶業務分布等。21， facc/ipac_ping：檢查rnc上的ip通路。ipac_ping -z 10.244.87.2 -d 10.244.73.49：在rnc上用etmfg板控制平面地址ping sgsn信令平面地址，檢查ps通路狀態。(-z src -d dst send echo request from ip) facc 用etmfx板地址去ping 基站上fe板的用戶平面地址，檢查iub_ip是否通路。22， cedhr：print dynamic cell data or capacity usage (rnc only).ced | grep k0001a1 查看某小區數據及無線容量占用情況。23， pst:查看定義的統計。?pgets:查看定義的統計中具體的counter? pmom:查看rnc中所有存在的counters.? pcr：定義統計。24， ca