實用文庫匯編之各版本IPG激光器開啟外控模式

1、*實用文庫匯編之IPG激光器開啟外控模式*1. IPG YLR有屏版:注：開啟外控模式請先注意激光器是否出光。(1) 、點擊IPG顯示屏的INT；：1 27.8DegC7 - - r QCWH LOGP/SOHGuide Beamn m；Emissionmon%0(2) 、選擇Modulation,將其更改為OFF；1ReturnReturnModulati onJOFfSXGateEnabledGateDisabledExt Guide ControlOFFAnalog ControlOFF ,PulseSettingExt Emission Control OFF(3)、外

2、控模式已開啟，點擊QfW欄，進行功率選擇，選擇完畢請點擊set；YLR-150/150(MJCO|Ext Emissi on ControlON :;Ext Guideh ControlOFFModulationAnalog! ControlOFF |Pulse Setti ngP/SINTINTQCWfOOJO%Guide Beam'|BBEmission1000.10(4)、功率選擇完畢，可以開始岀光，打開start按鈕;(3)、點擊Emission,倒計時完畢之后，激光器出光，請注意激光，謹慎操 作。YLR-150/150(XaCWPeak Pwr | Temp | Jnjuln

3、LOC JP/SnIRTINTGuide BeamONEmission FQCW| won% Starting Emission卿oo。Set302. IPG YLR無屏版：(1) 、請使用網線使激光器和工控機通訊。(2) 、網線連接后，請點擊電腦右下角，打開網絡和共享中心;(4)、點擊屬性;(5) 下拉，選擇Internet協議4 (TCP/Ipv4)，點擊屬性;(6)、將ip地址改成與圖片一致，點擊確定;（7）、打開瀏覽器，輸入192. 168. 3.230；Q http:/192.16&.3.230/< 8)、選擇Modulation Mode,點擊DISA

4、BLE,開啟外控模式;FirmwareCom municati onConlig-RMOTONICSMonitoringIG337 Web User Utility vl .6OHCase Temperature, eC：25.3Device ID：OHBoard Temperature CC!27.3Revision：Avg. Power, W：Peak Power, W：丫 LR70（PMM>WC32769；289；353Status0 Cmd Buffer Overflow8 Aiming Beam On1.Overheat9.Pulse Too Short2.Emission O

5、n10.CWModc3 Back Reflection110 PS ON/OFFA Analog Pwr. Control12J Modulation5丿 Reserved13J Reserved6丿 Reserved14丿 Reserved7J Reserved15J Reserved16 Gate Mode24 Low Temperature17丿 Reserved25 PS AlarmIB HW Emission Ctrl26丿 Reserved19.PS Failure27.HWAim Beam Ctrl20丿 Reserved28 Aiming Beam Alarm21丿 Reser

6、ved29 Crhical Enor 22_j Reserved30 Fiber Interlock23J Reserved31J ReservedPulse Generator| Disable PS (9)、拖動紅線處的選擇欄，改變功率大小，選擇Emission,點擊ON,激光 器已出光，請注意安全。MunHoringFirmwareAvg. Power, W： Peak Power, W:OffCase Temperature, *C： Board Temperature, SC:25.3Device ID： Revision：YLR-700-MM-WCOff27.632769;289;

7、353StatusIG337 Web User Utility vl .6Communication ConfigSPHOTONICSENABLE ENABLEModulation ModeGate ModeDISABLEInternal modeSUABLECurrent Setpoint %tmissivn0.Cmd Buffer Overflow8 Aiming Beam On16.Gotc Mode24.Low Temperature1 Overheat9 Pulse Too Short17丄 Reserved25 PS Alarm2Emission On10.CW Mode18 HW

8、 Emission Ctri2G丿 Reserved3 Back Reflection110 PS (ON/OFF)19 PS Failure270 HWAim Beam Ctrl4 Analog Pwr. Control12Modulation20丿 Reserved28 Aiming Beam Alarm5丿 Reserved13y Reserved21Reserved29.Critical Error6丿 Reserved14丿 Reserved22丿 Reserved30 Fiber Interlock7J Reserved15Reserved23丿 Reserved31丿 Reserved01000.010.7Analog Power buntrolAiming Beam2、IPG YLS激光器：(1) 、YLS模塊的激光器和無屏版一樣，要更改ip地址，將ip地址更改為: 192. 168. 100. 1