DIN2848-2002鋼制法蘭管和有襯里的鋼制及鑄鐵制法蘭管件.PN10、PN25和PN

1、.DIN2848-2002鋼制法蘭管和有襯里的鋼制及鑄鐵制法蘭管件.PN10、PN25和PN40 DEUTSCHE NORM June 2002 Lined ?anged steel pipes and ?anged steel or cast iron ?ttings rated for pressures of 10 bar (PN 10), 25 bar (PN 25) and 40 bar (PN 40) ICS 23.040.60 Flansch-Rohre aus Stahl und Flansch-Formstücke aus Stahl und Gusseisen m

2、it Auskleidung PN 10, PN 25 und PN 402848Supersedes December 1993 edition. In keeping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker. Contents Page Foreword . . . . . . . . . . . . . . .

3、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Conc

4、epts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 Dimensions and designations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 .1 Flanged elbows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5、. . . . . 4 4.2 Flanged tees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.3 Flanged tapers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.4 Reducers. . . . . . . . . . . . . . . . . . . . . . . . . . . .

6、 . . . . . . . . . . . . . . . . . . . . . 10 4.5 Spacers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.6 Blank ?anges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.7 Flanged pipes . . . . . .

7、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.8 Instrument nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 5 Tolerances and limit deviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.1 Angular

8、ity tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.2 Limit deviations for length l8 (pipes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 5.3 Limit deviations for lengths l1 to l7, l9 and l10 (?anged ?ttings). . . . . . . . 33 5.4 Limit d

9、eviations for ?anges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6 Wall thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.1 Wall thickness of steel components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

10、3 6.2 Wall thickness of cast iron components . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.3 Lining thickness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 7 Materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11、. . . . . . . . . . 34 8 Designs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 9 Technical delivery conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 ? No part of this translation may be reproduced without the pri

12、or permission ofDIN Deutsches Institut für Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,Copyright Deutsches Institut Fur Normung E.V. has the exclusive right of sale for German Standards (DIN-Normen).Provided by IHS under license with DIN No reproduction or networking permitt

13、ed without license from IHSNot for Resale-,-,-ForewordThis standard has been prepared by the Normenausschuss Rohrleitungen und Dampfkesselanlagen (Pipe-lines and Boilers Standards Committee).Continued on pages 2 to 34.Translation by DIN-Sprachendienst.In case of doubt, the German-language original s

14、hould be consulted as the authoritative text.Ref. No. DIN 2848 : 2002-06English price group 14 Sales No. 011404.05 Page 2DIN 2848 : 2002-06 Amendments This standard differs from the December 1993 edition as follows: a) The scope of the standard has been extended to include pressure ratings PN 25 and

15、 PN 40. b) For PN 10 instrument nozzles, the d4 value for a size DN1 of 25 was corrected and branch sizes (DN2) 40 and 50 have been dropped. c) Designations for steel and cast iron have been updated. d) Some new steel grades have been introduced. e) The speci?cations have been harmonized with DIN EN

16、 1092-1. f) The standard has been editorially revised. Previous editions DIN 2848: 1976-07, 1993-12; DIN 2848-10: 1982-01; DIN 2848-11: 1982- 01; DIN 2848-12: 1982-01. All dimensions are in millimetres. -,-,-1 Scope This standard speci?es dimensions and technical delivery conditions for ?anged steel

17、 pipes and ?anged steel or cast iron ?ttings, with lining, which are intended to be used at pressures of 10 bar (PN 10), 25 bar (PN 25) or 40 bar (PN 40). The components speci?ed in this standard may also be used without lining. The lengths speci?ed include the lining thickness, a (see ?gure 8). 2 N

18、ormative references This standard incorporates, by dated or undated reference, provisions from other publications. These norma-tive references are cited at the appropriate places in the text and the titles of the publications are listed below. For dated references, subsequent amendments to or revisi

19、ons of any of these publications apply to this stand-ard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. DIN 875 Steel squares DIN 876-1 Surface plates Natural hard rock surface plates Requirements and testing

20、DIN 876-2 Surface plates Cast iron surface plates Requirements and testing DIN 1626 and DIN 1629*) DIN 2275 Feeler gauges DIN 2605-2 Steel butt-welding pipe ?ttings Elbows and elbows for use at full service pressure DIN 2609 Steel butt-welding pipe ?ttings Technical delivery conditions DIN 2642 PN 1

21、0 loose ?anges with weld-neck and plain collar DIN 2874 Flanged steel pipes and steel and cast iron ?anged ?ttings lined with PTFE or PFA Technical delivery conditions DIN 2875 Flanged steel pipes and ?anged ?ttings lined with soft or hard rubber Technical delivery con-ditions DIN 17457 Welded circu

22、lar austenitic stainless steel tubes subject to special requirements Technical delivery conditions DIN 17458 Seamless circular austenitic stainless steel tubes subject to special requirements Technical delivery conditions DIN EN 764-3 Pressure equipment Part 3: De?nition of parties involved *) Trans

23、lators note. Standards DIN 1626 and DIN 1629 have been superseded by DIN EN 10208-1, DIN EN 10216-1, DIN EN 10217-1, DIN EN 10224, DIN EN 10296-1 and 10297-1.Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN No reproduction or networking permitted without license f

24、rom IHSNot for Resale Page 3DIN 2848 : 2002-06 DIN EN 1092-1 DIN EN 1563 DIN EN 10025 DIN EN 10208-1 DIN EN 10216-1 DIN EN 10217-1 DIN EN 10224 DIN EN 10253-2 DIN EN 10296-1 DIN EN 10297-1 Flanges and their joints Circular ?anges for pipes, valves, ?ttings and accessories Part 1: Steel ?anges, PN de

25、signatedFounding Spheroidal graphite cast iron (includes Amendment A1:2002)Hot rolled unalloyed structural steel products Technical delivery conditions (includes Amendment A1:1993)Technical delivery conditions for steel pipes for use with combustible ?uids Part 1: Pipes of requirement class ASeamles

26、s steel tubes for pressure purposes Technical delivery conditions Part 1: Non-al-loy steel tubes with speci?ed room temperature propertiesWelded steel tubes for pressure purposes Technical delivery conditions Part 1: Non-alloy steel tubes with speci?ed room temperature propertiesNon-alloy steel tube

27、s for the conveyance of aqueous liquids including water for human con-sumption Technical delivery conditionsButt welding pipe ?ttings Part 2: Wrought carbon and ferritic alloy steels with speci?c in-spection requirements*)Welded circular steel tubes for mechanical and general engineering purposes Te

28、chnical delivery conditions Part 1: Non-alloy and alloy steel tubesSeamless circular steel tubes for mechanical and general engineering purposes Technical delivery conditions Part 1: Non-alloy and alloy steel tubes 3 Concepts The concepts de?ned in DIN EN 764-3 shall apply. 4 Dimensions and designat

29、ions The designs shown are for illustrative purposes only; however, the dimensions of pipes and ?ttings shall be as speci?ed. *) Currently at draft stage.-,-,- Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN No reproduction or networking permitted without license

30、 from IHSNot for Resale Page 4DIN 2848 : 2002-06 4 .1 Flanged elbows Type A 90° elbow, series 3 as in DIN 2605-2, or as in DIN EN 10253-2 Detail X (scale 2:1) (sectional view) (types C and D, revolved by 45°)Type B90° elbow, series 5 as in DIN 2605-2,or as in DIN EN 10253-2 Designatio

31、n of a steel (St) elbow, type A, PN 10, DN1 100, with 4 mm chloroprene rubber (CR) lining:Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN No reproduction or networking permitted without license from IHS-,-,-1 100, without lining: Elbow DIN 2848 A 10 100 StElbow D

32、IN 2848 A 10 100 St 4 CRNot for Resale Page 5 DIN 2848 : 2002-06 Table 1: 90° elbowsType A DN120253240506580100125150200250300350400500 1) Type BLength l2 PN 40 PN 1095110130150180220255320385440 395485570655745 57071083091010301300 5907408559501080 PN 25 115138155185230265335400465 60075589097

33、51105PN 40 d11) PN 10 26,933,742,448,360,376,188,9114,3139,7168,3219,1273,0323,9355,6406,4508,0 120140165205245285365450525600680830 Length l1PN 25 Not available. Use type B. 125150175220260305 380465545635715 The outside diameter, d1, of cast iron components shall be subject to agreement. Table 2:

34、45° elbowsType C DN120253240506580100125150200250300350400500 d11) PN 10 26,933,742,448,360,376,188,9114,3139,7168,3219,1273,0323,9355,6406,4508,0 8085100115135150190225260290325390 213254290325370 8595110130150170 220260305345390 Not available. Use type D. Length l3PN 25 PN 40 PN 1065708090105

35、120135165190215270335385430480585 290365410470530 Type DLength l4PN 25 708895110130145180205240 300380445495660PN 40 Copyright Deutsches Institut Fur Normung E.V. Provided by IHS under license with DIN No reproduction or networking permitted without license from IHS -,-,- For 1), see table 1. Not for Resale Page 6 DIN 2848 : 2002-06 4.2 Flanged tees Designation of an all-?anged steel (St) tee, PN 10, DN1 100, reducing on branch DN2 50, with 4 mm chloroprene rubber (CR) lining: DN12025 32 40 50 65 Copyright Deutsches Institut Fur Normung E.V. Provided by IHS un