9-199-26風機樣本

1、9-19 、9-26 型離心通風機一、用途1.1 9-19、9-26 型離心通風機，一般用于鍛冶爐及高壓強制通風，并可廣泛用于輸送物料、輸送空氣及無腐蝕性不自燃、不含粘性物質之氣體。介質溫度一般不超過50( 最高不超過 80) ，介質中所含塵土及硬質顆粒不大于3150mg/m 。二、規格與結構特征2.1 風機葉輪直徑的分米數即為風機的機號, 用阿拉伯?dāng)?shù)字表示。機號后的字母表示風機的傳動方式，傳動方式常用的有：“A”式表示與電動機直聯傳動（葉輪裝在電機軸上） ?！癈”式表示通風機懸臂，皮帶輪在軸承外側傳動。“D”式表示通風機懸臂，有支撐、聯軸節傳動。2.2 風機的旋向分為左、右旋二種，其區分方法

2、是，從傳動方向正視葉輪，風機工作時葉輪順時針旋轉的為右旋，反之則為左旋。2.3 風機的出氣口方向一般均制成90 度，如用戶有特殊要求，可在定單上注明（風機的各種出口角度見圖1）。以下視圖均從電機一端正視圖 1為便于客戶安裝、調試，同時供應鋼結構的整體支架及減振支架。2.4 風機主要由葉輪、機殼、進風圈、軸承座等部件組成。其中葉輪由曲線型輪蓋、葉片、直板輪盤組成， 并經靜、動平衡校正。軸承座采用滾動軸承用鈣基脂潤滑。三、風機的性能3.1 風機的性能參數可見性能表3.2 在性能表各工況點，所需電機功率：3式中： Q-流量（ M/h ）N-電機功率（ kw）P-全壓（ mmH2O）-全壓效率 m-機

3、械效率“ A”式為 1，“C”式為 0.96K-電機容量安全系數， 2-5kw 取 K=1.2, 大于 5kw, 取 K=1.153.3 、所附性能參數表是在一定轉速下，標準狀態下風機性能參數， 如通風機的轉速、葉輪直徑或氣體密度發生變化，則性能參數換算公式如下：換換算算D =DmD=D mD D mD D m22222222公條n nmn=nmnnmn=nm式 件項目壓力換算流量換算功率換算效率四、 安裝、調試和運轉3.1安裝前應對風機各部件進行全面的檢查， 葉輪與機殼的旋轉方向是否一致， 各部聯接是否牢固，葉輪轉動后有無碰擦，如發現問題應立即給予調整。3.2安裝時注意檢查機殼內不得遺留工具

4、和雜物， 進出風管道聯接時應自然吻合， 不得強行聯接，絕對不允許將管道的重量加在風機上，并注意風機主軸的水平。3.3對聯軸器或帶傳動的風機，要檢查聯軸器或帶輪、皮帶是否安裝可靠。兩帶輪位置是否在一條中心線上， 風機軸與電機軸的同心度是否符合技術要求 （徑向位移0.1mm，傾斜度 0.8/1000 ）。3.4風機安裝完畢， 可進行試運轉， 在風機啟動時必須在無載荷即將進風調節門關閉出風調節稍開的情況下進行（特別是鍋爐引風機或高溫通風機），在啟動過程中應嚴密注視電流，不得超過電流額定值，如情況良好，逐步將閘門開啟到工況點為止。3.5當風機啟動后達到正常轉速時，應檢查軸承溫度是否正常（一般不宜高于8

5、0）如發現風機有劇烈的振動， 軸承溫度迅速上升及異常聲響等反?，F(xiàn)象時必須緊急停機檢查。五、維護與保養5.1 為了避免由于使用不當而引起的故障和事故發生，延長風機的使用壽命， 必須加強風機的維護和檢修。5.2 風機進氣口前應裝過濾裝置或除塵器，若進氣口不安設備時，必須加防護網，以防止異物吸入打壞葉輪。5.3 定期清除風機及輸送管道內部的灰塵污垢。5.4 定期更換潤滑脂。5.5 根據下列故障產生原因進行檢修：a) 風機劇烈振動1. 基礎的剛度不夠或不牢固。2. 進氣口與葉輪碰擦。3. 部件間或地腳螺栓聯接松動。4. 葉輪鉚接松動或葉輪變形。5. 進出氣口管道安裝不良，產生共振。6. 葉片積垢，磨損

6、，葉輪變形，軸彎曲使轉子產生不平衡。7. 帶輪安裝不正，電機軸和風機軸不同心。b) 軸承溫度過高1. 潤滑脂失效或混入灰塵、砂粒等雜質。2. 軸承座、蓋聯接螺栓過緊或過松。3. 滾動軸承損壞。c) 電流過大1. 氣體的密度過大，使電機超載。2. 電網電壓太低或單相斷電。六、特別警示6.1風機安裝完畢應使電機可靠接地。6.2每次啟動風機時應嚴密關閉進氣風門，待轉動正常后才能開啟風門。6.3風機運行中嚴禁進入異物。9-19 型離心通風機性能表軸功率電動機外型尺寸轉速流量Motor長×寬×高機號傳動方序號全壓Power ofspeedCapacitySizeNo式 TypeNoP

7、aShaftm3/h規格型號功率r/minkWTypeL×W× HPower kWmm155228700.60266728510.68Y80L-21.1374228340.763.5A2840481028000.84373× 588×631593927600.926109826321.01Y90S-21.57123724981.118132523801.52182435841.16297036651.33Y90L-22.23111636471.484A29004126435971.64435×587×7155141035071.806

8、155833841.97Y100L-237170432532.171117446032.072139746842.383161646722.68Y112M-244.5A29004183945802.98489×661×7825206244473.296228142973.63Y132S2-25.57250441124.031161056973.432193257683.983225457404.50Y132S2-27.55A29004257656395.04609×734×8685284455175.546316653236.177348850806.8

9、6Y160M 1-2111226271826.052271472327.02Y160M 1-2113316772367.935.6A29004361971098.88638×821×9625399669549.7664448670910.88Y160L-218.574901640012.09軸功率電動機外型尺寸轉速流量Motor長×寬×高機號傳動方序號全壓Power ofspeedCapacitySizeNo式 TypeNoPaShaft規格型號m3/h功率r/minkWTypeL×W×HPower kWmm1278282988.55

10、2333984049.9133895836211.206A290044451821312.5454915803313.7865472775015.3676028739017.0713220914910.9123865926512.6534509921914.306.3A290045153905516.0055690885717.5966334854319.6076978814821.79146101171719.83255321186822.99364541180725.997.1D2900473761159629.09581441134031.98690661093535.637998810

11、42639.62165941503436.02279131522941.75392321515147.218D29004105501487752.835116491454658.086129681402164.717152871336271.951329736204.52395736655.223461636475.908D14504527535846.605582535077.266648433848.097714432318.99傳動方轉速流量軸功率機號序號全壓Power of式speedCapacityNoNoPaShaftTyper/minm3/hkW1469545978.112563

12、346559.4135672463210.639D145047511455111.9058294445313.0869233429714.58710171410116.2110D145016440584013.3827942549116.03Y160M 2-215Y160L-218.5Y160L-218.5Y200L 1-230Y200L 2-237Y250M-255Y280S-275Y315S-2110Y132M-47.5Y160L-415電動機Motor規格型號功率TypePower kWY160L-415Y180L-422Y200L-430769×900×989782

13、×925×10851230×1043×12781256×1173×14281256×1173×1278外型尺寸長×寬×高SizeL×W× Hmm1289×1318×18561317×1464×174839445589118.59410947574021.12512450549523.84613952524426.79Y225S-437715455495829.8819407736423.58211158749128.25Y225M-44

14、5313269742832.7611.2D1450415380723637.221565×1641×1947517491692742.02619602660947.21Y280S-475721713624652.661599031826.842738832378.203878532109.51Y180L-61511.2D960410182312810.801565×1641×1947511580299612.19612978286013.70Y200L 2-622714375275015.28112577922940.84215512939048.92Y

15、280S-475318447931056.7212.5D1450421381906864.461603×1830×2156524316867872.76Y315S-4110627251827881.75730186782291.18軸功率電動機外型尺寸轉速流量Motor長×寬×高機號傳動方序號全壓Power ofspeedCapacitySizeNo式 TypeNoPaShaft規格型號功率r/minm3/hL×W× HkWTypePower kWm85210270404314.20Y200L 2-62231

16、2213400916.4612.5D960414156390718.711603×1830×1947516099374121.11618042357123.72Y250M-637719985337726.461176701166871.972217931187486.22Y315M 1-41323259161177199.9614D145043004011464113.592031×2050×240053416310967128.22Y315M 2-420063828610457144.067424099878160.69111690500420.891

17、4D960214428509025.02Y250M-6372031×2050×2400317158504729.01419888491732.97522618470937.21625348449441.81728078424946.6312637715425140.3123253115700168.0916D145033868615563194.8944484115151221.4655099514488249.98117463657040.72221538668348.78325613662756.5616D960429687645664.27533762618072.5

18、5Y315S-675Y355M 3-43152091×2340×2735Y315S-6752091×2340×2735637837589881.52741912557592.929-26 型離心通風機性能表轉速序流量軸功率機號傳動方全壓Power ofspeed號CapacityNo式 TypePaShaftr/minNom3/hkW1219838523.112236838203.283253637653.464A29004270637843.655287736073.866304435024.067321534074.291313049105.5123

19、40748635.873368547766.244.5A29004396346616.645423745457.066451544127.547479242567.981429365039.122470659849.8035114586910.485A290045527572511.2355941555312.0066319538112.8176762518013.6516032761016.0926612754617.275.6A290037185740018.4747766721819.7958346700021.1568919678122.57Y315L 1-6110電動機Motor功率

20、規格型號Power kWTypeY132S 1-25.5Y132S 2-27.5Y160M 1-211Y160M 2-215Y160L-218.5Y180M-222Y200L 1-230外型尺寸長×寬×高SizeL×W×Hmm521×711×761642×799×849676×887×937823×993×105379500652724.0517419873622.7228132866324.3838837849526.086A290049552828627.94510265

21、803629.86610970778431.87711685749333.96傳動轉速序流量軸功率機號全壓Power of方式speed號CapacityNoPaShaftTyper/minNom3/hk9929415961631.12310230942933.286.3A2900411056919535.66511883861538.12612699893640.67713525831043.351122921242750.272134751232156.573146431207860.497.1A29004158261177664.845170091145169.

22、306181771105573.947193601063578.821175841595595.7221927715818102.7332094715504109.868D290042264015112117.7552433214644125.8562600314177134.2872769613634143.1418792383411.9629639380212.84310473372913.738D1450411320363814.72512166352915.73613001342116.79713848329417.89112518486921.56213723482823.14314

23、913473624.759D1450416118462023.53517322448138.35618512434330.25719717418132.24Y200L 1-230Y200L 2-237電動機Motor規格型號功率TypePower kWY225M-245Y250M-255Y280S-275Y315S-2110Y315M 1-2132Y315L 2-2200Y180M-418.5Y200L-430Y200L-430Y225M-445外型尺寸長×寬×高SizeL×W×Hmm967×1117×11671317×12

24、259×13611349×1418×15281348×1418×15281392×1594×1691轉速序流量軸功率機號傳動方全壓Power ofspeed號CapacityNo式 TypePaShaftr/minNom3/hkW117172614235.69219319605639.19321465592043.0210D1450423612576147.10525758556051.35627905530955.35730052506559.34124126774762.90227142763769.0733015774

25、6475.8211.2D1450433173726483.01536189700990.50639205669197.547422216382104.58115978334618.25217969329920.04319966322522.0011.2D960421963314024.09523959303126.26625956289528.31727953276330.351335409713108.912377329575119.603419259356131.3012.5D14504461179103143.755503108782156.706545038381168.9075869

26、57993181.10122206419731.61224981412134.71327757402838.1012.5D960430533392141.72533309378545.48636084361549.02738860345052.56機號傳動轉速序流量全壓軸功率方式speed號CapacityPower of ShaftNoPaTyper/minNom3/hkW14712112285191.9414D145025301112109210.7835890211830271.546479211508297.3電動機外型尺寸Motor長×寬×高規格型號功率SizeP

27、ower kWL×W× HTypemmY250M-4551433×1770×1870Y280S-475Y315S-41101694×1983×2088Y315M-4132Y225M-6301694×1983×2088Y250M-637Y315M 2-41601755×2212×2312Y355M 2-4250Y280S-6451755×2122×1250Y315S-675電動機外型尺寸Motor長×寬×高規格型號功率SizeL×W× H

28、Power kWTypemmY355M 2-42502199×2418×2562JS-138-441057068211099324.167657210589349.378246310095374.5131197526255.70Y315S-675235097518891.17338997507167.1514D960442897493673.522199×2481×2945542796476480.15Y315M 2-6110650696454986.39754596434192.6317033916250439.1JSQ-147-45002791311

29、6014482.2(3000V)38792315640529.416D145049671615210579.6JSQ-158-42271×2830×2945510550014663631.8850(3000V)611430013983681.0712309013324730.21465696911108.602523906813119.263582116659130.92Y355M 1-618516D9604640326481143.342271×2830×29455698546254156.256756755971168.42Y355M 3-62207

30、814965696183.589-19、 9-26 型 A 式傳動離心通風機外形及安裝尺寸進風口法蘭出風口法蘭外形尺寸安裝尺寸型聯結螺栓聯結螺栓號D1D2D3MA1A2A3A4Mx1 ×nx2 ×nE1E2E3E4B1B2abcn-數量數量9-19-3.5160178199688611713216361436× 335× 458824854629539884801502504-159-19-4180205230689813214818261442× 340× 4167228660033546594791902504-159-19-4.

31、52002252506811215116019861445× 344× 4756.5322.5794472548108902203004-159-19-52282542846812516817121461450× 348× 4835356.5830472583121952303404-159-19-5.62502803108813918819924861456.3×354.5×494140110014956831361013404064-209-19-6.325828831888155210255310101466× 362

32、× 410724501044530749153105.53804104-209-19、 9-26 型 A 式傳動離心通風機外形及安裝尺寸進風口法蘭出風口法蘭外形尺寸安裝尺寸型聯結螺栓聯結螺栓號D1D2D3MA1A2A3A4Mx1 ×nx2 ×nE1E2E3E4B1B2abcn-數量數量9-26-42282542846813620318425061455× 357× 4724287832472570125992303404-159-26-4.52502903208815122620127661459× 362.5× 4810.

33、53259004956961411053404064-209-26-52803203608816024521630861464× 371× 4903362945495753160110.5-3404064-209-26-5.63153553958818828023532861853× 461× 5100140211245107801801193704404-209-26-6.335539543510820230926236961859× 468× 51123.5452.51247560940201127.54705504-249-19

34、、9-26 型 D 式傳動離心通風機外形及安裝尺寸型號進風口法蘭出風口法蘭外形尺寸基礎尺寸D1D2D3n1 ×d1A1A2A3A4n2 ×d2X1 ×nX2 ×nEFGKLMHabcdef9-19-7.12933203508-1017123223129214 ×868×366 ×41774661042509123012782805204403005905101939-19-83403704008-1020027827034814 ×880×380 ×42005251173572125614282

35、805204403035905102079-19-94064505008-1021828929836914 ×863×466 ×52265901318644128915862805204403105905102239-19-104505005508-1024432830438818 ×869×472 ×52506561464715131717482805204403145905102399-19-11.250656062012-1027236737246718 ×1079×483 ×52807351641801156519473757006203667807002619-19-12.55