塑料模具專業用語中英文對照介紹

1、塑料模具專業用語中英文對照介紹模具述語一、入水:gate進入位:gate location水口形式:gate type大水口:edge gate細水口: pin-point gate水口大小:gate size轉水口:switching runner/gate唧嘴口徑:sprue diameter二、流道: runner熱流道:hot runner,hot manifold熱嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圓形流道:round(full/half runner流道電腦分析:mold flow analysis流道平衡:runn

2、er balance熱嘴:hot sprue熱流道板:hot manifold發熱管:cartridge heater探針: thermocouples插頭:connector plug插座: connector socket密封/封料: seal三、運水:water line喉塞:line lpug喉管:tube塑膠管:plastic tube快速接頭:jiffy quick connector plug/socker四、模具零件:mold components三板模:3-plate mold二板模:2-plate mold邊釘/導邊:leader pin/guide pin邊司/導套:bu

3、shing/guide bushing中托司:shoulder guide bushing中托邊L:guide pin頂針板:ejector retainner plate托板:support plate螺絲: screw管釘:dowel pin開模槽:ply bar scot內模管位:core/cavity inter-lock頂針:ejector pin司筒:ejector sleeve司筒針:ejector pin推板:stripper plate縮呵:movable core,return core core puller 扣機(尼龍拉勾:nylon latch lock斜頂:lift

4、er模胚(架: mold base上內模:cavity insert下內模:core insert行位(滑塊: slide鑲件:insert壓座/斜雞:wedge耐磨板/油板:wedge wear plate壓條:plate撐頭: support pillar唧嘴: sprue bushing擋板:stop plate定位圈:locating ring鎖扣:latch扣雞:parting lock set推桿:push bar頂板:eracuretun活動臂:lever arm分流錐:spure sperader水口司:bush垃圾釘:stop pin隔片:buffle彈弓柱:spring r

5、od彈弓:die spring中托司:ejector guide bush中托邊:ejector guide pin鑲針:pin銷子:dowel pin波子彈弓:ball catch喉塞: pipe plug鎖模塊:lock plate斜頂:angle from pin斜頂桿:angle ejector rod尼龍拉勾:parting locks活動臂:lever arm復位鍵、提前回桿:early return bar氣閥:valves斜導邊:angle pin術語:terms承壓平面平衡:parting surface support balance模排氣:parting line ven

6、ting回針碰料位:return pin and cavity interference?？偢叱銎C(jī)規格:mold base shut hight頂針碰運水:water line interferes withejector pin料位出上/下模:part from cavith (core side模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate. 不準用鑲件: Do not use (core/cavity insert用鈹銅做鑲件: use beryllium copper insert初步(正式模圖設計:preliinary (final mold design反呵:reverse core彈弓壓縮量:spring compressed length穩定性好:good stability,stable強度不夠:in