Basics建模要件

1、BASICS建模要件STREAMS汽2 Passive Types (Type 0 and Type 6)- 2 被動型 (類型 0 和類型 6)水流動* Pressure Drop*壓降HEAT EXCHANGERS熱交換器GENERAL HEAT EXCHANGER WITH SPECIFIED SHELL AND TUBE INLET STREAMS帶有特定殼側和管側進口汽水流動的通用熱交換器REHEATER再熱器GENERAL HEAT EXCHANGER WITH SPECIFIED HEAT SOURCE OR SINK帶有特定放熱源和吸熱源的通用熱交換器Stream Type 4

2、 Inlet類型4汽水流動的進口3. Nuclear Reheater (Type 22) “S” Port核電再熱器（類型22）“S” 端口INPUT輸入Input Data輸入數據1. Generic Input (optional unless otherwise noted)通用輸入（除非另行說明，均可選）- Cycle Flags (required, but input is default)- 循環標識（必選，輸入是默認的）- Output Tables- 輸出表格- Screen Display Variables- 屏幕顯示的變量- Calculation Flags- 計算

3、標識- User Specified Material Properties- 用戶指定的物質屬性- 2nd Law Reference Data- 熱力學第二定律參考數據- End Notes結束說明Input ProcessoSets and Cases設置和事例r*輸入處理器*2. Run 2 cases using the data from Sets 1 and 2 for the first case, and Sets 1-4 for the second case.運行兩個案例：第一個案例使用設置1和2中的數據，第二個案例使用設置1-4中的數據SCHEDULED VARIABL

4、E VALUES CALCULATED (All Special Features Calculated)計算預定變量值（計算所有特殊功能）FLAG SETTINGS AND DATA FOR SYSTEM系統標識旗的設置和數據· Short Cuts!· 快捷方式!· Operational Variables· 運算Operations (Equations)· 操作（方程）· 變量Input/Output Processor· 輸入/輸出處理器· Input/Output Values Must be Dep

5、endent輸入/輸出值必須是有函數關系的Operational Variables操作變量specifies 輸入IWWMass flow (lbm/hr, kg/sec)IWW 質量流量(lbm/hr, kg/sec)IHCHeat Transfer Coefficient IHC傳熱系數IBSpressure drop equation B coefficient IBS壓降方程式B系數（參見幫助）- Uses Special Output Processor to Export Data and Results- 使用特殊輸出處理器輸出數據和結果。specifies 規定Conserv

6、ation of Mass質量守恒All Inlet Ports Must be Resolved所有進口端口必須均已確定。· Turbine, Types 17· 汽輪機Heat Exchangers, Types 20-23, 28-29· 熱交換器，類型20-23, 28-29- ，類型1-7Flag Design Mode in Input (or Choose Design Mode Component Type)輸入中使用標識設計模式（Flag Design Mode）或選擇設計模式部件類型（Design Mode Component Type）。Tu

7、be out Shell exit port superheat管道出口（殼側出口以標準為基礎的預測Ref-BasedPredictiveUse of Overall Heat Transfer Coefficients總體換熱系數的使用· Components in Design Mode設計模式中的部件Condenser Sensitivity Study凝汽器靈敏度以標準為基礎的預測Boiler Operating Parameter Study鍋爐運行參數分析STREAMS汽水流動Fluid Passes Through Unchanged* 流體流動時狀態恒定* Press

8、ure Drop*壓降* Heat Loss*熱損失GENERAL HEAT EXCHANGER WITH SPECIFIED HEAT SOURCE OR SINK帶有特定放熱源和吸熱源的通用熱交換器· Mixers (Type 50s) on the Main Steam Line, the Main Condensate/Feedwater Line, and Extraction Lines Must Route Main Flow Through “IA” and “U” Ports· 主蒸汽管路、主凝結水/給水和抽氣管路上的混合加熱器(類型50s)必須通過端口“

9、IA” 和 “U” 與總汽水流動相連接。IBHEnergy flux or Energy flow rate (Btu/hr, W)IBH能通量或能流速率(Btu/hr, W)ILBMass (lbm, kg) ILB質量(lbm, kg)IPPPressure (psia, kPa) IPP壓力 (psia, kPa)IVVSpecific Volume (ft3/lbm, m3/kg) IVV比容(ft3/lbm, m3/kg)ILKSteam Rate 耗汽率 IUAThermal Conductance IUA換熱率ITCThermal Conductivity換熱性 ITRThermal Resistance 熱電阻IFHVolume Flow Rate體積流量GENERAL HEAT EXCHANGER WITH SPECIFIED SHELL AND TUBE INLET STREAMS帶有特定殼側和管側進口汽水流動的通用熱交換器 Lines 行，線路，線Component N