美國電動類廚房電器安全標準的基本要求ppt課件

1、家用電動類食物處置器具的平安要求 Presented by: Dreamer Yang (楊華國): dreamer.yangintertek: 020-82455 Dec. 26, 2021Welcome to this seminar Your Global Partner in Quality!ETL 是大發明家愛迪生于1896年興辦的. 我們是按照 ANSI/UL/CSA等規范來做認證測試的.常用電動類食物處置器具的規范ANSI/UL982 Motor-Operated Household Food Preparing Machines (Sixth Edition Rev.Jun.

2、09, 2021)ANSI/UL763 Motor-Operated Commercial Food Preparing Machines (4th Edition Rev. Oct. 24, 2021)CSA C22.2 No.195 Motor Operated Food Processing Appliances (Household and Commercial) Rev. 2021CSA C22.2 No.1335.2.14 Portable Electrical Motor-Operated and Heating Appliances: Particular Requiremen

3、ts for Electrical Motor-Operated Kitchen Appliances (Consumer & Commercial Products) (Rev. 2021)主要內容 適用范圍構造要求性能測試闡明書和名牌消費線上的測試常見不良構造分析問題與回答適用范圍家用電動類食物處置,短時間運轉的器具.線銜接或永久銜接,標稱電壓為120V的器具.帶充電座的電池供電的器具.假設器具帶有加熱功能,那么同時還要另外思索相關烹飪類的規范. 適用范圍 典型器具Food processorblenderWand type mixer Food mixer適用范圍 典型器具Coffee

4、mill Food chopper coffee grinder適用范圍 典型器具 reamer type juicer centrifugal juicer can opener適用范圍 典型器具Meat slicerKnife sharpenerIce cream freezer適用范圍 典型器具Liquid mixerMeat grinderBaby-food chopper適用范圍SummaryQuestions & answer構造要求外殼過流維護電源線銜接內部布線電氣絕緣元件和組裝帶電部件馬達開關電氣間隙接地防止對人體損傷的維護(Protection against persona

5、l injury)外殼一切的帶電和運動部件(除功能部件外)需求被包圍在外殼內.假設UL測試手指經過外殼的任何小于25.4 mm的開孔不能觸及到?jīng)]有絕緣的導體或漆包線，那么接受這樣的開孔.對于大于25.4 mm的開孔,假設在以下圖二的開口范圍內無裸露的帶電部件和漆包線,那么是可以接受的.(X等于五倍的最大能插進開口圓棒的直徑)在思索帶電和運動部件的可接觸性要求時，不需求用工具就能去除的部件需求被移除.外殼Test Finger外殼對于自動控制的器具,其應帶有防止熔融金屬,熄滅顆粒等掉落到支撐面上, 通?？梢杂肂arrier 來到達這一要求, 但barrier必需符合以下圖要求.外殼非金屬外殼的防

6、火等級應至少為HB, HWI等級應至少為4.不產生點弧的帶電部件到非金屬外殼的間隔應至少為0.8 mm,假設間隔小于0.8 mm那么其應滿足UL746C的要求.產生點弧的帶電部件(開關觸片,馬達換向器)到非金屬外殼的間隔應至少為12.7 mm,假設間隔小于12.7 mm(但是不得小于0.8 mm),那么其應滿足HAI等級應至少為1的要求.對于家用的,便攜式的,間歇性運轉的, 有人照看的器具,其非金屬外殼的溫度至少可以耐80度的溫度.以下將分別對非金屬資料的防火等級,HWI, HAI 專門講解.ANSI/ULASTMCSAIECISO94HBD635HBC22.2 No. 0.17HB *606

7、95-11-10(A)HB, HB40, HB7594V-0,V-1,V-2D3801V-0,V-1,V-2C22.2 No. 0.17V-0,V-1,V-260695-11-20(B)V-0,V-1,V-2945VA, 5VBD50485VA, 5VBC22.2 No. 0.175VA, 5VB60695-11-205VA, 5VB94VTM-0, -1, -2D4804VTM-0, -1, -2C22.2 No. 0.17VTM-0, -1, -29773VTM-0, -1, -294HBF,HF-1, -2D4985HBF,HF-1, -2C22.2 No. 0.17HBF,HF-1,

8、-29772HBF,HF-1, -2外殼外殼外殼外殼How to read yellow card for polymeric material?外殼You can find the material what you want under the following website: my.home1.ul/portal/page/portal/ULIQ/UL_iQ_Home_Page電源銜接電源線類型便攜式/櫥柜式/墻上安裝式產品: HPN, SPT-2, SVO, SVT, SVTO 或同等類型.電動刀和充電式產品(充電時不能用)： SPT-1 也可以用.手持式產品重小于0.68kg):

9、 SPT-1, coiled type and max. extended length of 2.1m.Rated voltage not less than that of the appliance and have suitable ampacity.對于室外運用的器具其電源線至少應為SJW or SJTW.電源線的大小應至少為18AWG. Power supply connectionsCord length電源線長度Hand-supported手持式產品: 1.52mCountertop operation臺式產品: 0.61mWall-mounted墻安裝式產品: 0.6-1.4

10、mAttachment plug電源插頭2-wire polarized type兩線極性插頭3-wire grounding type三線接地型插頭Power supply connectionsStrain relief(電源線拉力測試Metal clamp may be use on SPT-1, SPT-2, SVT & SVTO cords protected by varnished-cloth tubing, vulcanized fiber under the clamp, thermoplastic tubing is not acceptable for thermopla

11、stic cords. Nonmetallic clamp may be directly used on SPT-1, SPT-2, SVT & SVTO flexible cords without tubing. cord shall be restrained from any rotation that will cause movement of internal wiring at splices and terminals電源線需求經受拉力測試156N，1分鐘，無位移.推力測試力施加于電源線1 inch位置，26.7N的力被運用).普通情況下拉力測試較難經過，建議電源線在運用線

12、扣的同時，再運用一個UL結，這樣測試會容易經過.Internal wiring內部線要有可靠的維護, 通常要用外殼包圍住.Thermoplastic insulated wire employed for internal wiring shall be standard building wire or appliance-wiring material that is provided with insulation appropriate for the purpose.內部線要遠離銳邊,毛刺,及運動部件,內部線穿過金屬外殼的孔時通常要加線護套, 或者該孔的外表要加工的非常光滑.一切的內

13、部線要防止與溫度高的部件(如晶體管的散熱片)接觸,除非其耐溫值足夠高.一切的內部線的銜接要可靠,焊接一定要勾焊.內部線的相關電氣規格不應小于器具的規格.帶電部件和電氣絕緣載流部件的資料通常為銀,銅,銅合金等其他同等的資料, 不銹鋼也可以用來當作載流部件.帶電部件通常要可靠固定,不能轉動和挪動,單靠外表之間的摩擦來防止帶電部件的轉動是不接受的,用梅花介子是可以接受的.支撐帶電部件的資料應該是具有能抗?jié)裥缘男阅?支撐帶電部件的塑膠資料應該符合UL746C 的要求.固定易碎性的絕緣部件應該不能太緊,以防止該部件裂開.一切用做絕緣的Tube, 都要求有認證.MOTOR 馬達常見的幾種馬達Series

14、motorDC motorMOTOR 馬達常見的幾種馬達Syc motorSP motorMOTOR 馬達馬達資料的選用支撐除magnet wire 以外的帶電部件的資料MOTOR 馬達馬達資料的選用支撐magnet wire 的資料做隨機測試的馬達只能當class A 絕緣來對待.高過class A 的絕緣系統要按UL1446 來做絕緣系統的認證.MOTOR 馬達馬達的過載維護自動控制器具的馬達應該提供過載維護, 并且其要符合UL2111的測試.Creamer freezer, butter churn的馬達應該提供過載維護, 并且其要符合UL2111的測試.對于其他帶有馬達熱維護的非自動控

15、制器具,其要能經受賭馬達測試等相關測試,并且其要符合UL2111的limited short circuit 測試.For appliances provided with an automatic reset or user-resettable overload-protective device where automatic restarting would result in a risk of injury to persons, each of three representative appliances shall be energized and have their ro

16、tors stalled until the overloadprotective device opens. While still energized, and the rotor no longer stalled, the representative appliances shall then be allowed to cool down until the overload-protective device closes. The representative appliance shall not automatically restart or have the possi

17、bility of accidentally being restarted. A distinct and deliberate motion shall be required to restart the representative appliance.開關和控制器過流維護器應接在器具的L線端, 但對于1Hp的便攜式非自動啟動的120V的器具,并且假設過流維護器只是充任一個補充的維護安裝, 那么可以不符合以上要求.開關的電流和電壓rating值應不小于器具的電流和電壓rating值.對于非點觸式開關,應該明確標示ON,OFF位置.假設便攜式器具帶有一個大于1/3 馬力的馬達,那么該器具

18、必需提供一個開關來控制馬達的ON/OFF.器具不能帶有through-cord switch.對于手動的,線銜接的單極開關,可控硅或其他控制器(都是用于器具的ON/OFF 目的),應該銜接到火線上(Ungrounded conductor).對于電子式開關(通常是經過可控硅或繼電器來實現),器具處于stand-by 的形狀下, 任何一個電子元器件失效, 不能觸發器具, 除非沒有危險的運動部件可以觸及到.(例外: 器具帶有一個機械開關, 并且加一個在stand-by 形狀下閃爍的紅色指示燈是可以接受的).器具的互鎖開關是不能用test finger觸發的.Spacing電氣間隙Spacings

19、between field wiring terminal of opposite polarity, and the spacing between a field wiring terminal and any other uninsulated metal part must 6.4mm.Spacings at other than field wiring terminals，refer to following form: Overcurrent protection and grounding Overcurrent protective device電流維護安裝wholly in

20、accessible from outside電流維護安裝從產品外殼上不能觸及connect to the ungrounded conductor of the power supply cord電流維護安裝需求銜接在火線上.Grounding, 以下幾種情況,器具要求接地:The following types of appliances shall have provision for grounding:a) An appliance for use in damp or wet locations (see 5.9, 5.10, and 5.22); eg. Canopies, ma

21、rquees, roofed open porches.b) An appliance intended for outdoor use;c) An appliance intended to be used on a circuit operating at more than 150 V to ground; andd) An appliance intended for permanent connection to the supply source.器具的接地電阻不能大于0.1歐姆.Protection against personal injury防止人身損傷的維護The inst

22、ruction manual of the package containing a basic appliance and various attachments intended to be sell as a complete unit shall indicate what attachments are intended for use with the basic appliance假設各種配件與主機一同作為一個整體出賣，那么其闡明書應闡明何種配件與主機一同運用；假設配件與主機分開包裝并出賣，但由制造商引薦與主機一同運用，那么應對配件進展編號，同時，主機闡明書應標明其編號；重要平安

23、指示，如適用于配件，那么應與配件一同提供. Protection against personal injuryMoving members運動部件constructed to reduce the likelihood of its malfunction, its unintentional realease, and its loosening of a part產品在構造上要減少能夠呵斥的誤動作，無意的零落及松動.series motor is to be operated at a voltage equal to 1.3 times rated voltage for 1 minu

24、te with no load器具在無外部負載下，在1.3倍額定電壓下任務1分鐘。測試后,能呵斥損傷的零件不應松動.requirement: no parts can be worked loose沒有部件能在任務時發生零落或松動.Stability穩定性No overturn shall be occurred when placed on a 10 inclined plane, if container is provided, either fill or empty situation shall be considered產品不通電放在10 的斜臺面上，產品不能翻倒，假設產品配有容

25、器，那么此容器需求組合不同形狀進展此測試.假設產品帶有一容器, 那么容器應加水到額定容量(沒有標示的話,那么加水到最大量); 開罐機測試事不帶罐; Salad maker 和 food grinder 在空載下測試.Protection against personal injuryEnclosure & guard外殼及維護安裝all moving parts that may cause injury shall be enclosed一切能夠導致?lián)p傷的運動部件需求被外殼包裹住(除非一些特殊功能的器具).not possible to actuate an interlock with t

26、est probe測試手指不能使互鎖安裝動作.Feeding mechanism shall be safe進料機制要平安可靠，不能損傷到運用者Pusher shall provided with continuous manual feeding當器具需求延續手動進料時，應提供推桿. 假設全部包裹住產品的運動部件會使得產品失去預定的功能(例如,電動刀),那么要帶有一個適宜的控制器,并且闡明書中要帶有相關的警告語.Protection against personal injuryOFF position shall be visually indicated 產品的OFF位置應能容易讓運用者

27、目視判別.Actuator for an interlock shall be located that unintended operation is unlikely. 互鎖機構應防止運用者誤觸發. Operation in normal use shall not inconvenience the operator so as to encourage deliberated defeat of an interlock正常運用時應使操作者便于操作, 使得操作者不會故意破壞互鎖機構. Interlock should not be capable of being defeated b

28、y food material互鎖機構應不會被器具正常運用時積聚起來的食物破壞掉. Interlock shall not be capable of being defeated互鎖機構應不會被隨便破壞.Surface Temperatures外表溫度During the temperature test, a temperature on the surface of an appliance that may be contacted by the user shall be not more than the value indicated in following form:Appl

29、iances器具Blender攪拌器prevent cutting assembly from disengaging from container during any normal operation position. 攪拌機切削組件應可靠裝配，防止在任何正常任務位置切削組件從攪拌容器中掉出來. open-top container of a blender shall provided with a cover having one or more openings, each opening having dimension = 25.4mm攪拌器的開口容器應帶有一個單孔或多孔的蓋子

30、,其尺寸不能大于2-5/8(66.7mm)，而不小于1(25.4mm); 但對于用來倒水的蓋子上的邊緣孔,其尺寸可以小于25.4mm.A blender container shall not break or crack during normal use正常運用過程中，攪拌容器不應破裂, 可以經過打冰塊測試來驗證.For CSA standard (CSA C22.2 No.195): 要求容器頂部到產品的刀片位置的最小間隔為150 mm.Appliances器具Blender攪拌器 To determine if a glass blender container complies wi

31、th 30.4.6, open top or closed top, three blender containers shall be conditioned and tested as follows: a) Each of the glass containers under test shall be lightly abraded with 150 grit silicon carbide sandpaper. Both the internal and external surfaces shall be scuffed laterally and vertically. b) A

32、fter the container is abraded, the entire assembly (container, cutter assembly, jar nut, etc.) shall be assembled and heated until thermal saturation to 55C (130F) in either an aircirculating oven or in a hot water bath. c) The container assembly shall be removed and immediately filled with a mixtur

33、e of 2 cups ice cubes and 8 fl oz. alcohol (vodka). Ice cubes must be approximately the size to enclose a 1-in (25-mm) cube. The ice cubes and alcohol shall be maintained, separately, at a temperature of -5C (23F) or less prior to the test. The ice cubes and alcohol, when moved from storage, are to

34、be used within 5 minutes. d) The mixture shall be pulsed five (5) times on highest speed. Each pulse shall consist of 3 seconds on followed by 3 seconds off.Appliances器具Food processor/food chopper食物處置器具Average inside diameter of the feed opening must 76.2mm,and the cutters are recessed not less than

35、 4 Inches below the plane of the opening. If the average inside diameter is reduced to 2 Inches, the distance may be less than 88.9 mm. 進料孔的平均直徑要小于63.5mm，最大直徑不能大于76.2mm, 并且刀片要在分開口平面102mm.(假設進料孔的平均直徑不大于50.8mm, 那么刀片只需分開口平面88.9mm).Discharge chute should also comply with the feed opening dimensions requ

36、irements出渣口也需求滿足進料孔的尺寸要求, 除非無任何危險的運動部件可以觸及到.Should provided with a cover actuated interlock食物處置機應帶有蓋子互鎖安裝，防止不小心碰到運動部件. When the cover is removed, the moving parts shall stop within 4 seconds當取下蓋子，運動部件在4秒內必需停頓.If the cover can actuate the interlock switch without the cover being properly locked in pl

37、ace any access opening to moving parts that can be created by the misalignment shall have a maximum vertical dimension of not more than 1 inch (25.4 mm) between the bowl and cover. A force of 1 lbf (4.4 N) is to be employed to move the cover.假設沒有將蓋子鎖到位的情況下能驅動互鎖開關，那么運動部件任何開口在碗與蓋子之間的垂直方向最大尺寸應不大于1(25.4

38、 mm)。用一個1 lbf4.4N的力來撥動蓋子. Appliances器具Food processor/food chopper食物處置器具S-blade and slicing blade shall provide with stems, finger holes, handles or the like for insertion and removal假設食物加工機帶S刀片及切刀組合件，那么刀片應帶刀桿，手指孔，手指位，手柄等，防止在裝拆刀片時將手指刮傷.The interlock system shall be capable of completing 10,000 cycles

39、 of operation in the intended manner without malfunction.互鎖安裝應能任務10,000次而無誤動作。在開場測試時及測試完成后，其停頓時間均應不超越4秒. Appliances器具Coffee mill/咖啡豆磨機Should provided with a cover actuated interlock食物處置機應帶有蓋子互鎖安裝，防止不小心碰到運動部件. When the cover is removed, the moving parts shall stop within 4 seconds當取下蓋子，運動部件在4秒內必需停頓.I

40、f the cover can actuate the interlock switch without the cover being properly locked in place any access opening to moving parts that can be created by the misalignment shall have a maximum vertical dimension of not more than 1 inch (25.4 mm) between the bowl and cover. A force of 1 lbf (4.4 N) is t

41、o be employed to move the cover.假設沒有將蓋子鎖到位的情況下能驅動互鎖開關，那么運動部件任何開口在碗與蓋子之間的垂直方向最大尺寸應不大于1(25.4 mm)。用一個1 lbf4.4N的力來撥動蓋子The interlock systemshall be capable of completing 6,000 cycles of operation in the intended manner without malfunction.互鎖安裝應能任務6,000次而無誤動作。在開場測試時及測試完成后，其停頓時間均應不超越4秒.Appliances器具Coffee g

42、rinder 咖啡研磨機For the feed opening, the diameter is less than 2-1/2 inches (63.5 mm) or maximum diagonal dimension of the opening is less than 3 inches (76.2 mm), and the maximum extremity of a moving part that can cause injury to persons is recessed not less than 3-1/2 inches (88.9 mm) from the neare

43、st edge of the plane of the opening;進料孔的直徑要小于63.5mm，或最開口尺寸小于76.2mm, 并且刀片要在分開口平面88.9mm.For the discharge opening, 1)The diameter is less than 2-1/2 inches (63.5 mm) or the maximum diagonal dimension of the opening is less than 3 inches (76.2 mm), and the maximum extremity of a moving part that can ca

44、use injury to persons is recessed not less than 3-1/2 inches (88.9 mm) from the nearest edge of the plane of the opening; 2) A guard or guards are provided to limit the maximum width of the opening to 3/8 inch (9.5 mm) at the point of exposure to the risk of injury to persons, and the closest point

45、of a moving part that can cause injury to persons is recessed at least 1/4 inch (6.4 mm) from the nearest edge of the guards where it limits the opening to 3/8 inch (9.5mm); Appliances器具Coffee grinder 咖啡研磨機For the discharge opening (contd) 3) A guard is used to automatically cover the opening when t

46、he discharge container removed. 4) The discharge opening is in the horizontal plane, its diameter is less than 2-1/2 inches (63.5 mm) or the maximum diagonal dimension is less than 3 inches (76.2 mm) and the distance from a moving part that can cause injury to persons to the nearest edge of the plan

47、e of the opening is not less than 2 inches (50.8 mm). A 3/8 inch (9.5 mm) diameter rod is not to contact a moving part that can cause injury to persons when it is inserted into the opening a distance of 3- 1/2 inches (88.9 mm) or less.Appliances器具Vegetable shredders/slicers 切菜機A hopper feed opening

48、shall be a maximum of 3 inches (76.2 mm); Moving parts shall be a minimum of 4 inches (101.6 mm) below the plane of the throat of the opening. 用于手動裝料的漏斗頸部及其它任何開口的內徑必需 76.2 mm，能對人體呵斥損傷的運動部件應位于開口頸部平面下方 101.6 mm.例外：假設漏斗頸部的平均內徑小于50.8 mm，那么運動部件與開口頸部平面的間隔可降低到88.9 mm.For a vegetable shredder/slicer provide

49、d with a discharge chute, the discharge chute shall comply with the feed-opening requirements對帶有出渣孔的切菜機，其出渣孔應符合進料孔要求.A vegetable shredder/slicer shall be provided with a cover-actuated interlock which complies with the requirements切菜機產品必需提供一個蓋子起動的互鎖維護安裝， 且這個安裝需求滿足：互鎖安裝應能任務10,000次而無誤動作。在開場測試時及測試完成后，其

50、停頓時間均應不超越4秒. Appliances器具centrifugal juicers 離心式榨汁機A hopper feed opening shall be a maximum of 3 inches (76.2 mm); Moving parts shall be a minimum of 4 inches (101.6 mm) below the plane of the throat of the opening. 用于手動裝料的漏斗頸部及其它任何開口的內徑必需 76.2 mm，能對人體呵斥損傷的運動部件應位于開口頸部平面下方 101.6 mm.例外：假設漏斗頸部的平均內徑小于50

51、.8 mm，那么運動部件與開口頸部平面的間隔可降低到88.9 mm.A centrifugal juicer shall be provided with an interlock to restrict access to the juicing disk. The interlock system shall be capable of completing 6000 cycles of operation in the intended manner without malfunction.離心式榨汁機產品需求提供一個互鎖維護安裝，該安裝必需能經受6000個循環的耐久性測試，測試后應功能

52、正常。測試條件：產品在無載條件，最高速度下進展，同時保證產品電機的線圈溫度不超越正常任務形狀下所獲得的最大溫度.CONSTRUCTIONSummaryQuestions & answerPerformance產品性能要求Leakage current test走漏電流測試 0.5mA for either portable or fixed applianceThe meter is to have an input impedance of 1500 ohms resistive shunted by a capacitance of 0.15 f.PerformanceInput test

53、輸入功率測試The power input of an appliance was measured when the appliance is operated under a condition of max. normal load輸入功率測試要在產品最大正常負載條件下進展. Max. normal load is considered to be that load which approx. as closely as possible the most serve conditions of normal useThe measured input in watts or ampe

54、res to an appliance may be less than the marked rating by an amount greater than the deviation shown in following form if the temperature rises are not exceeded when the appliance is subjected to an additional temperature test when loaded to nameplate rating產品的輸入功率可以低于下表的要求， 但是必需得經受產品在額定值下面的溫升測試的要求.

55、PerformanceMax. normal loadFood mixerOperated for a total of 15 minutes in the intended manner, involving all speed setting, and with a load material representing the actual service conditions總任務時間15分鐘，每個速度下面的任務時間如下Time at each speed, T =(15/2N-1) minN means no. of speed settingsBlending mixer10 cyc

56、les of operation, each cycle consisting of 3 min of operation followed by a minute off period10個操作循環，3分鐘“ON， 1分鐘“OFF; 對于點動式的開關 那么為1分鐘“ON， 1分鐘“OFF; Loaded with a mixture of diced carrots & water in ratio 2:3負載是水和胡蘿卜的3：2混合物, 對于低檔那么用水為負載.Dimension of diced carrot pieces胡蘿卜尺寸:Half with dimension 12.7mm

57、and 1/2 horsepowera對馬達功率1/2 hp的器具,為1000+2*額定電壓V對電動刀,那么為2500V Humidity test 潮態測試Exposed to humidity of 88+/-2% at 32+/-2 C for 48 hours, shall comply with the Leakage current test 產品在潮態箱中條件為：濕度設置為88+/-2% ，溫度設置為32+/-2 C ，時間為48小時，然后滿足漏電流測試Locked rotor test 電機堵轉測試假設帶有金屬外殼的產品30 sec: coffee mill, hand mix

58、er, can openermanual), knife, meat grinder, slicer, etc. 堵轉時間：30秒5 min: coffee grinder, blender, food processor, can opener(other than manual)。堵轉時間：5分鐘Performance帶電部件溢流測試 1)正常運用時需參與液體的臺式產品: 把器具放置在正常運用位置, 蓋上蓋子, 但是參與孔打開, 器具的液體容器裝滿鹽水溶液(每升蒸餾水含1/2克氯化鈉), 此外等于容器容量15%的液體在分鐘內被灌入. a) 當器具設計為液體容器位于馬達上方, 讓開關關閉或運

59、作進行溢流測試, 兩種情況都做. b) 當液體容器不位于馬達上方時,液體容器灌注入測試溶液, 以最大速度操 作器具直到?jīng)]有飛濺. 操作器具三次, 在每個操作之間, 關掉器具, 再次給 液體容器填充測試溶液. 在此測試過程中器具應符合走漏電流測試. 測試 后, 器具應符合耐電測試. 2) 為確定能否有液體引入外殼內: 把器具置于平底盤里, 盤的長度和寬度最小 是被測器具底部的兩倍. 盤內填充1/6“(1.6mm)深的鹽水溶液(每升蒸餾水含 1/2克氯化鈉), 以最大速度操作器具1分鐘. 在此測試過程中器具應符合走漏 電流測試. 測試后, 器具應符合耐電測試. 例外:假設產品帶有底孔和腳且底孔離桌

60、面的間隔大于inches (50.8 mm)那么 不需做2)的測試. Performance馬達熱塑性資料的測試 1) Normal Conditioning 測試: 三個馬達放入度的烤箱中放置個小時假設一切的這些資料的大于度，那么可不做此測試后立刻打高壓, 需經過高壓測試, 且沒有顯著的軟化及變形. )Abnormal Conditioning 測試: 一個代表性器具的馬達轉子或電樞被堵轉后, 在額定電壓讓繞組通電. 馬達不帶電的金屬部件通過一個3A非時間延遲保險絲連接地. 經受條件持續7小時或直至:作為繞組破裂, 絕緣體熔化或類似情形的結果, 馬達燒壞.一個可靠的非用戶改換的保護裝置燒壞,