按鍵中斷程序

1、夫1個LED指示燈，對應的GPIO為:PC0輸出為1點亮LED輸出為0關閉LED另外PC1為外部中斷觸發：按鍵按下時為低電平，即可設置為低電平觸發/* GPIO配置函數夫/void GPIO_Configuration(void)/*定義2個結構體變量夫/GPIO_InitTypeDef GPIO_InitStructure;/夫開啟GPIOB，GPIOC，復用口時鐘的時鐘夫/RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);RCC_A

2、PB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);/夫給GPIOC_Pin_1 一個初始值夫/GPIO_ResetBits(GPIOC, GPIO_Pin_0);配置IO 口，初始化IOGPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 ;/將連接LED的GPIO設置為推挽輸出GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;/設置為2MHZ的速度，響應時間，沒要求越小越好GPIO_Mode_IPU為輸出GPIO_InitStructure.GPIO_Speed = GPI

3、O_Speed_2MHz;/初始化GPIOCGPIO_Init(GPIOC, &GPIO_InitStructure);/夫給 KEY_InitStructure.GPIO_Pin KEY_InitStructure.GPIO_ModeKEY_InitStructure.GPIO_Speed 付初始值夫/GPIO_InitStructure.GPIO_Pin=GPIO_Pin_1;/設置為上拉輸入GPIO_InitStructure.GPIO_Mode=GPIO_Mode_IPU ;/設置為2MHZ的速度GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2M

4、Hz;/初始化GPIOBGPIO_Init(GPIOC, &GPIO_InitStructure);/設置GPIOC的中斷標志位GPIO_EXTILineConfig(GPIO_PortSourceGPIOC, GPIO_PinSource1);夫夫夫夫夫夫配置extI*void EXTI_Configuration(void) /定義一個結構體EXTI_InitTypeDef EXTI_InitStructure;/設置中段線EXTIInitStructure.EXTILine = EXTILine1;/使能中斷線EXTIInitStructure.EXTILineCmd = ENABLE

5、;/設置中斷模式EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;/設置中斷觸發方式EXTI_InitStructure.EXTI_Trigger =EXTI_Trigger_Falling;/初始化中斷EXTI_Init(&EXTI_InitStructure);*配置優先級*void NVIC_Configuration(void) /定義一個結構體NVIC_InitTypeDef NVIC_InitStructure;/設置優先級組NVIC_PriorityGroupConfig(NVIC_PriorityGroup_0) ;/設置存入

6、寄存器NVIC_SetVectorTable (NVIC_VectTab_FLASH ,0 x0);/設置 外部中斷1線這里對應的是外部中斷1因?yàn)槲疫x的是之前的PC1來觸發另外EXTI5_9_IRQn則表示外部中斷5-9線。NVIC_InitStructure.NVIC_IRQChannel =EXTI1_IRQn;/使能優先級NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;/配置搶斷優先級這個是決定中斷跳轉可否嵌套的依據夫夫夫非常重要NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority =0;/

7、配置響應優先級NVIC_InitStructure.NVIC_IRQChannelSubPriority =0;/初始化優先級NVIC_Init(&NVIC_InitStructure);/主函數int main(void)/*/調用初始化GPIO函數GPIO_Configuration ();EXTI_Configuration ();NVIC_Configuration ();while(1);在it.c中的程序：void EXTI1_IRQHandler(void)(delay_GSM(10000);if( EXTI_GetITStatus (EXTI_Line1) = 1 )(EXTI_ClearITPendingBit (EXTI_Line1);send_gprs_da