震雄注塑機規格

1、說明DESCRIPTIONSUNITJM55MK-C射膠部分INJECTION UNIT射膠量（硬膠）Shot Weight (PS)oz.2.4gm.69射膠容量Swept Volumecm380螺桿直徑Screw Diametermm.28射膠壓力Injection Pressurekgf./cm21715螺桿行程Screw Strokemm.130螺桿轉速Screw Speed RangeR.P.M0-140熔膠能力Plasticizing Capacitykg/hr.40料斗容量Hopper Capacityl.31射嘴行程N(yùn)ozzle Travel Strokem.m.220螺桿長度

2、直徑比Screw L/D Ratio19鎖模部分CLAMPING UNIT鎖模力Clamping ForceMp.55開模行程O(píng)pening Strokemm.220連接柱內距（水平垂直）Space Between Tie Bars (HV)mm.mm.310310容模量（最薄-最厚）Mould Thickness (Min-Max)mm.80-320模板最大距離Maximum Daylightmm.540油壓頂針推力Hydraulic Ejector ForceMp.2.2油壓頂針行程Hydraulic Ejector Strokemm.75定位法蘭直徑Mould Register Hole

3、 (H7)mm.100動力/電熱POWER/HEATING 油泵馬力Pump MotorKW.(HP)7.5(10)電熱量Heating CapacityKW.4.8系統壓力System Pressurekfg./cm2145溫度控制區No. of Temp. Control Zones2+1其它OTHERS循環時間Dry Cycle Timesec.1.6占地面積Floor Spacem.m.31.2裝箱尺寸Shipping Dimensionm.m.m.3.511.6油缸容量Oil Tank Capacityl.150機重Machine Weight (Dry)ton.2.4說明DESCR

4、IPTIONSUNITJM88MK-C射膠部分INJECTION UNIT射膠量（硬膠）Shot Weight (PS)oz.4.5gm.128射膠容量Swept Volumecm3142螺桿直徑Screw Diametermm.36射膠壓力Injection Pressurekgf./cm21500螺桿行程Screw Strokemm.140螺桿轉速Screw Speed RangeR.P.M10-152熔膠能力Plasticizing Capacitykg/hr.65料斗容量Hopper Capacityl.31射嘴行程N(yùn)ozzle Travel Strokem.m.219螺桿長度直徑比S

5、crew L/D Ratio19鎖模部分CLAMPING UNIT鎖模力Clamping ForceMp.88開模行程O(píng)pening Strokemm.270連接柱內距（水平垂直）Space Between Tie Bars (HV)mm.mm.360360容模量（最薄-最厚）Mould Thickness (Min-Max)mm.127-350模板最大距離Maximum Daylightmm.620油壓頂針推力Hydraulic Ejector ForceMp.3油壓頂針行程Hydraulic Ejector Strokemm.75定位法蘭直徑Mould Register Hole (H7)

6、mm.100動力/電熱POWER/HEATING 油泵馬力Pump MotorKW.(HP)7.5(10)電熱量Heating CapacityKW.5.6系統壓力System Pressurekfg./cm2145溫度控制區No. of Temp. Control Zones2+1其它OTHERS循環時間Dry Cycle Timesec.1.2占地面積Floor Spacem.m.3.81.3裝箱尺寸Shipping Dimensionm.m.m.3.91.21.7油缸容量Oil Tank Capacityl.150機重Machine Weight (Dry)ton.3.4說明DESCRI

7、PTIONSUNITJM128MK-C射膠部分INJECTION UNIT射膠量（硬膠）Shot Weight (PS)oz.9gm.255射膠容量Swept Volumecm3283螺桿直徑Screw Diametermm.46射膠壓力Injection Pressurekgf./cm21687螺桿行程Screw Strokemm.170螺桿轉速Screw Speed RangeR.P.M10-200熔膠能力Plasticizing Capacitykg/hr.100料斗容量Hopper Capacityl.45射嘴行程N(yùn)ozzle Travel Strokem.m.280螺桿長度直徑比Sc

8、rew L/D Ratio20鎖模部分CLAMPING UNIT鎖模力Clamping ForceMp.128開模行程O(píng)pening Strokemm.305連接柱內距（水平垂直）Space Between Tie Bars (HV)mm.mm.410360容模量（最薄-最厚）Mould Thickness (Min-Max)mm.175-400模板最大距離Maximum Daylightmm.705油壓頂針推力Hydraulic Ejector ForceMp.3.4油壓頂針行程Hydraulic Ejector Strokemm.100定位法蘭直徑Mould Register Hole (

9、H7)mm.100動力/電熱POWER/HEATING 油泵馬力Pump MotorKW.(HP)15(20)電熱量Heating CapacityKW.13.4系統壓力System Pressurekfg./cm2175溫度控制區No. of Temp. Control Zones3+1其它OTHERS循環時間Dry Cycle Timesec.1.3占地面積Floor Spacem.m.4.460.98裝箱尺寸Shipping Dimensionm.m.m.4.71.11.6油缸容量Oil Tank Capacityl.300機重Machine Weight (Dry)ton.3.8說明D

10、ESCRIPTIONSUNITJM168MK-C射膠部分INJECTION UNIT射膠量（硬膠）Shot Weight (PS)oz.14gm.396射膠容量Swept Volumecm3435螺桿直徑Screw Diametermm.52射膠壓力Injection Pressurekgf./cm21437螺桿行程Screw Strokemm.205螺桿轉速Screw Speed RangeR.P.M10-150熔膠能力Plasticizing Capacitykg/hr.110料斗容量Hopper Capacityl.70射嘴行程N(yùn)ozzle Travel Strokem.m.300螺桿長

11、度直徑比Screw L/D Ratio20鎖模部分CLAMPING UNIT鎖模力Clamping ForceMp.168開模行程O(píng)pening Strokemm.350連接柱內距（水平垂直）Space Between Tie Bars (HV)mm.mm.460410容模量（最薄-最厚）Mould Thickness (Min-Max)mm.220-450模板最大距離Maximum Daylightmm.800油壓頂針推力Hydraulic Ejector ForceMp.4.5油壓頂針行程Hydraulic Ejector Strokemm.100定位法蘭直徑Mould Register Hole (H7)mm.120動力/電熱POWER/HEATING 油泵馬力Pump MotorKW.(HP)18.75(25)電熱量Heating CapacityKW.16系統壓力System Pressurekfg./cm2145溫度控制區No. of Temp. Control Zones3+1其它OTHERS循環時間Dry Cycle Timesec.1.6占地面積Floor Sp