齒輪機械機構類中英文翻譯@外文翻譯@外文文獻翻譯

外文原文 Gears Gears are vital factors in machinery ,which are uses to transmit power or motion from one shaft to another .They may be used only to transmit motion from one part of a machine to another,or they may be used to change the speed or the torque of one shaft with with relation to another.One of the first mechanism invented using gears wad the clock.In fact,a clock is little more than a train of gears.Considerable study and research have been made on gears in recent years because of their wide use under exacting conditions.They have to transmit heavier loads and run at high speeds than ever before.The engineers and the machinists all consider gearing the prime element in nearly all classes of machinery. Super Gears Spur gears will be considered first for several reasons.In the first place ,they are simplest and the least expensive of gears and they may be used to transmit power between parallel shafts,also,spur gears definitions are usually applicable to other types .It is important go understand the following definitions,since they are important factors in the design of any equipment utilizing gears. Diametric Pitch The number of teeth per inch of pitch cirle diameter .The diameter pitch is usually an integer .A small number for the pitch implies a large tooth size.Meshing spur gears must have the same diameter pitch .The speed ratio is based on the fact that meshing gears may have different-sized pitch circles and hence different number of teeth. Circular Pitch The distance from a point on one tooth to the corresponding point on an adjacent tooth ,measrued along the pitch circle.This is a liner dimension and thus bas liner units. Pitch Circle The circle on which the ratio of the gear set is based,when two gears are meshing ,the two pitch circles must be exactly tangent if the gears are to function properly.The tangency point is known as the pitch point. Pressure Angle The angle between the line of action and a line perpendicular to the centerlines of the two gears in mesing .Pressure Angles for spur gears are usually 14.5 or 20 degrees,although other values can be used.Meshing gears must have the same pressure angles.In the case of a rack,the teeth have the straight sides inclined at an angle corresponding to the pressure angle. Base Circle A circle tangent to the line of action (or pressure line ) .The base circle is the imaginary circle about which an involutes cure is developed .Most spur gears follow an involutes cure from the base circle to the top of the tootch,this cure can be visualized by observing a point on a taut cord an it is unwound from a cylinder .In a gear ,the cylinder is the best circle. Addendum The radial distance form the pitch circle to the top of the tooth . Dedendum The radial distance from file pitch circle to the root of the tooth. Clearance The difference between the addendum and the addendum. Face Width The width of the tooth measured axially. Face The surface between the pitch circle and the top of the tooth. Flank The surface between the pitch circle and the bottom of the tooth. Helical Gears These gears have their tooth element at an angle or helix to the axis of the gear.They are more difficult and expensive to make than spur gears,but are quieter and stronger. They may be used to transmit power between parallel shafts at an angle to each in the same or different planes. Herringbone Gears A herringbone gear is equivalent to a right-hand and a left-hand helical gear placed side by side.Because of the angle of the tooth,helical gears create considerable side thrust on the shaft. A herringbone gear corrects this thrust by neutralizing it ,allowing the use of a small thrust bearing instead of a large one and perhaps eliminating one altogether.Often a central groove is made round the gear for ease in machining. Bevel Gears Bevel gears are used to connect shafts, which are not parallel to each other.Usually the shafts are 90 deg.To each other, but they may be more or less than 90 deg.The two meshing gears may have the same number of teeth for the purpose of changing direction of motion only,or they may have a different number of teeth for the purpose of changing both speed and direction .The faces of the teeth lie on the surface of the frustum of a cone,therefore the teeth elements are not parallel to each other it can be seen that this lack of parallelism creates a machining problem so that two passes with a tool must be made.The tooth elements may be straight or spiral ,so that we have plain anti spiral evel gears. Worm and Worm Gears A worm-and-worm-gear combination is used chiefly where it is desired to obtain a high gear reduction in a limited space,normally the worm drivers the worm gear and is not reversible ,that is to say,the worm gear can not drive the worm.Most worms can be rotated in either direction,clockwise or counterclockwise. Racks A rack is a gear with an infinite radius,or a gear with its perimeter stretched out into a straight line.It is used to change reciprocating motion to rotary motion or vice versa.A lathe rack and pinion is a good example of this mechanism. Various materials are used in manufacturing gears .Usually,the materials selected depends on the method used for making the gear and the application to which it will be put.Gears can be cast,cut,or extruded.Typical materials include cast iron,cast steel,plain carbon steel,alloy steel aluminum,phosphor bronze,laminated phonetics,and nylon. 中文翻譯 齒輪 齒輪是機器中的動力元件 ,用來傳遞軸與軸之間的運動及動力。它們可能僅被用來傳遞運動 ,即機器的一個部分到另一個部分 ,或者被用來改變軸與軸之間相對速度和轉矩 ,第一個被發現用齒輪的機器是鐘表 ,事實上 ,鐘表的齒輪與火車上的齒輪相比是非常小的。由于齒輪在實際環境中的廣泛應用 ,人們在齒輪的應用方面進行了 許多的研究和調查。現在 ,齒輪傳動比起以前來不得不傳遞很重的載荷 ,和在高速度下運轉。目前工程師和機械師都在考慮存在于機械中的這種因素。 直齒圓柱齒輪 直齒圓柱齒輪被作為傳動中的首選有許多原因。它們是最簡單也是最廉價的，并且它們可以被用作傳動平行軸之間的力，還有它的概念同于其它類型的齒輪，以下的幾個定義是非常重要的，因為，它們在設計任何與齒輪有關的方面都是非常重要的。 徑節 節圓直徑單位距離上的齒數，徑節通常是一個整數。小小的一段齒距包括了許多的齒形。直齒圓柱齒輪嚙合的條件是必須有相同的徑節，齒輪的傳動比決定于 嚙合齒輪的不同的節圓和不同數目的齒數。 齒距 沿著節圓從齒上的一點到臨近齒上對應相同的另一點的距離，這是一個線尺寸和線性單位。 節圓 作為齒輪比率設定基礎的圓。若要是互相嚙合的齒輪正常運行，則兩節圓必須精確相切。 壓力角 運動方向與垂直于兩嚙合齒輪中心線的直線所形成的夾角。對于直齒圓柱齒輪壓力角為 14.5 度或 20 度，因此可以有許多的用途，相嚙合的齒輪必須有相同的壓力角。對于齒條，齒相對于直邊有與壓力角相同的傾斜角度。 基圓 與運動方向相切（或與壓力角方向相切）的圓?；鶊A是產生漸開線所假想的圓。許多直齒圓柱齒 輪都是漸開線從基圓到齒頂，當繃緊繩索從一個圓柱體展開時，仔細觀察繩索上某點的運動，即可想象出此段漸開線的形狀。在齒輪中，基圓是最主要的圓。 齒頂高 從節圓到齒頂?shù)膹较蚓嚯x。 齒根高 從節