外文翻譯--故障的分析尺寸的決定以及凸輪的分析和應用

外 文 翻 譯 故障的分析、尺寸的決定以及凸輪的分析和應用 系 部： 機械工程系 學生姓名： 指導教師： 職 稱： 副 教 授 專 業： 機械設計制造及其自動化 班 級： 學 號： 1 Failure Analysis， Dimensional Determination And Analysis，Applications Of Cams Abstract： It is absolutely essential that a design engineer know how and why parts fail so that reliable machines that require minimum maintenance can be designed； Cams are among the most versatile mechanisms available A cam is a simple two-member device The input member is the cam itself， while the output member is called the follower Through the use of cams， a simple input motion can be modified into almost any conceivable output motion that is desired Key words: failure high-speed cams design properties INTRODUCTION It is absolutely essential that a design engineer know how and why parts fail so that reliable machines that require minimum maintenance can be designed Sometimes a failure can be serious， such as when a tire blows out on an automobile traveling at high speed On the other hand， a failure may be no more than a nuisance An example is the loosening of the radiator hose in an automobile cooling system The consequence of this latter failure is usually the loss of some radiator coolant， a condition that is readily detected and corrected The type of load a part absorbs is just as significant as the magnitude Generally speaking， dynamic loads with direction reversals cause greater difficulty than static loads， and therefore， fatigue strength must be considered Another concern is whether the material is ductile or brittle For example， brittle materials are considered to be unacceptable where fatigue is involved Many people mistakingly interpret the word failure to mean the actual breakage of a part However， a design engineer must consider a broader understanding of what appreciable deformation occurs A ductile material， however will deform a large amount prior to rupture Excessive deformation， without fracture， may cause a machine to fail because the deformed part interferes with a moving second part Therefore， a part fails(even if it has not physically broken)whenever it no longer fulfills its required function Sometimes failure may be due to abnormal friction or vibration between two mating parts Failure also may be due to a phenomenon called creep， which is the plastic flow of a material under load at elevated temperatures In addition， the actual shape of a part may be responsible for failure For 2 example， stress concentrations due to sudden changes in contour must be taken into account Evaluation of stress considerations is especially important when there are dynamic loads with direction reversals and the material is not very ductile In general， the design engineer must consider all possible modes of failure， which include the following Stress Deformation Wear Corrosion Vibration Environmental damage Loosening of fastening devices The part sizes and shapes selected also must take into account many dimensional factors that produce external load effects， such as geometric discontinuities， residual stresses due to forming of desired contours， and the application of interference fit joints Cams are among the most versatile mechanisms available A cam is a simple two-member device The input member is the cam itself， while the output member is called the follower Through the use of cams， a simple input motion can be modified into almost any conceivable output motion that is desired Some of the common applications of cams are Camshaft and distributor shaft of automotive engine Production machine tools Automatic record players Printing machines Automatic washing machines Automatic dishwashers The contour of high-speed cams (cam speed in excess of 1000 rpm) must be determined mathematically However， the vast majority of cams operate at low speeds(less than 500 rpm) or medium-speed cams can be determined graphically using a large-scale layout In general，the greater the cam speed and output load， the greater must be the precision with which the cam contour is machined DESIGN PROPERTIES OF MATERIALS The following design properties of materials are defined as they relate to the tensile test 3 Static Strength The strength of a part is the maximum stress that the part can sustain without losing its ability to perform its required function Thus the static strength may be considered to be approximately equal to the proportional limit， since no plastic deformation takes place and no damage theoretically is done to the material Stiffness Stiffness is the deformation-resisting property of a material The slope of the modulus line and， hence， the modulus of elasticity are measures of the stiffness of a material Resilience Resilience is the property of a material that permits it to absorb energy without permanent deformation The amount of energy absorbed is represented by the area underneath the stress-strain diagram within the elastic region Toughness Resilience and toughness are similar properties However， toughness is the ability to absorb energy without rupture Thus toughness is represented by the total area underneath the stress-strain diagram， as depicted in Figure 2 8b Obviously， the toughness and resilience of brittle materials are very low and are approximately equal Brittleness A brittle material is one that ruptures before any appreciable plastic deformation takes place Brittle materials are generally considered undesirable for machine components because they are unable to yield locally at locations of high stress because of geometric stress raisers such as shoulders， holes， notches， or keyways Ductility A ductility material exhibits a large amount of plastic deformation prior to rupture Ductility is measured by the percent of area and percent elongation of a part loaded to rupture A 5%elongation at rupture is considered to be the dividing line between ductile and brittle materials Malleability Malleability is essentially a measure of the compressive ductility of a material and， as such， is an important characteristic of metals that are to be rolled into sheets Hardness The hardness of a material is its ability to resist indentation or scratching Generally speaking， the harder a material， the more brittle it is and， hence， the less resilient Also， the ultimate strength of a material is roughly proportional to its hardness Machinability Machinability is a measure of the relative ease with which a material can be machined In general， the harder the material， the more difficult it is to machine COMPRESSION AND SHEAR STATIC STRENGTH In addition to the tensile tests， there are other types of static load testing that provide valuable information Compression Testing Most ductile materials have approximately the same properties in compression as in tension The ultimate strength， however， can not be evaluated for 4 compression As a ductile specimen flows plastically in compression， the material bulges out，but there is no physical rupture as is the case in tension Therefore， a ductile material fails in compression as a result of deformation， not stress Shear Testing Shafts， bolts， rivets， and welds are located in such a way that shear stresses are produced A plot of the tensile test The ultimate shearing strength is defined as the stress at which failure occurs The ultimate strength in shear， however， does not equal the ultimate strength in tension For example， in the case of steel， the ultimate shear strength is approximately 75% of the ultimate strength in tension This difference must be taken into account when shear stresses are encountered in machine components DYNAMIC LOADS An applied force that does not vary in any manner is called a static or steady load It is also common practice to consider applied forces that seldom vary to be static loads The force that is gradually applied during a tensile test is therefore a static load On the other hand， forces that vary frequently in magnitude and direction are called dynamic loads Dynamic loads can be subdivided to the following three categories Varying Load With varying loads， the magnitude changes， but the direction does not For example， the load may produce high and low tensile stresses but no compressive stresses Reversing Load In this case， both the magnitude and direction change These load reversals produce alternately varying tensile and compressive stresses that are commonly referred to as stress reversals Shock Load This type of load is due to impact One example is an elevator dropping on a nest of springs at the bottom of a chute The resulting maximum spring force can be many times greater than the weight of the elevator， The same type of shock load occurs in automobile springs when a tire hits a bump or hole in the road FATIGUE FAILURE-THE ENDURANCE LIMIT DIAGRAM The test specimen in Figure 2.10a， after a given number of stress reversals will experience a crack at the outer surface where the stress is greatest The initial crack starts where the stress exceeds the strength of the grain on which it acts This is usually where there is a small surface defect， such as a material flaw or a tiny scratch As the number of cycles increases，the initial crack begins to propagate into a continuous series of cracks all around the periphery of the shaft The conception of the initial crack is itself a stress concentration that accelerates the crack propagation phenomenon Once the entire periphery becomes cracked， the cracks 5 start to move toward the center of the shaft Finally， when the remaining solid inner area becomes small enough， the stress exceeds the ultimate strength and the shaft suddenly breaks Inspection of the break reveals a very interesting pattern， as shown in Figure 2.13 The outer annular area is relatively smooth because mating cracked surfaces had rubbed against each other However， the center portion is rough， indicating a sudden rupture similar to that experienced with the fracture of brittle materials This brings out an interesting fact When actual machine parts fail as a result of static loads， they normally deform appreciably because of the ductility of the material. Thus many static failures can be avoided by making frequent visual observations and replacing all deformed parts However， fatigue failures give to warning Fatigue fail mated that over 90% of broken automobile parts have failed through fatigue The fatigue strength of a material is its ability to resist the propagation of cracks under stress reversals Endurance limit is a parameter used to measure the fatigue strength of a material By definition， the endurance limit is the stress value below which an infinite number of cycles will not cause failure Let us return our attention to the fatigue testing machine in Figure 2.9 The test is run as follows： A small weight is inserted and the motor is turned on At failure of the test specimen， the counter registers the number of cycles N， and the corresponding maximum bending stress is calculated from Equation 2.5 The broken specimen is then replaced by an identical one， and an additional weight is inserted to increase the load A new value of stress is calculated， and the procedure is repeated until failure requires only one complete cycle A plot is then made of stress versus number of cycles to failure Figure 2.14a shows the plot，which is called the endurance limit or S-N curve Since it would take forever to achieve an infinite number of cycles， 1 million cycles is used as a reference Hence the endurance limit can be found from Figure 2.14a by noting that it is the stress level below which the material can sustain 1 million cycles without failure The relationship depicted in Figure 2.14 is typical for steel， because the curve becomes horizontal as Napproaches a very large number Thus the endurance limit equals the stress level where the curve approaches a horizontal tangent Owing to the large number of cycles involved， N is usually plotted on a logarithmic scale， as shown in Figure 2.14b When this is done， the endurance limit value can be readily detected by the horizontal straight line For steel， the endurance limit equals approximately 50% of the ultimate strength However， if the surface finish is not of polished equality， the value of the endurance limit will be lower For 6 example， for steel parts with a machined surface finish of 63 microinches ， the percentage drops to about 40% For rough surfaces， the percentage may be as low as 25% The most common type of fatigue is that due to bending The next most frequent is torsion failure， whereas fatigue due to axial loads occurs very seldom Spring materials are usually tested by applying variable shear stresses that alternate from zero to a maximum value， simulating the actual stress patterns In the case of some nonferrous metals， the fatigue curve does not level off as the number of cycles becomes very large This continuing toward zero stress means that a large number of stress reversals will cause failure regardless of how small the value of stress is Such a material is said to have no endurance limit For most nonferrous metals having an endurance limit， the value is about 25% of the ultimate strength EFFECTS OF TEMPERATURE ON YIELD STRENGTH AND MODULUS OF ELASTICITY Generally speaking， when stating that a material possesses specified values of properties such as modulus of elasticity and yield strength， it is implied that these values exist at room temperature At low or elevated temperatures， the properties of materials may be drastically different For example， many metals are more brittle at low temperatures In addition， the modulus of elasticity and yield strength deteriorate as the temperature increases Figure 2.23 shows that the yield strength for mild steel is reduced by about 70% in going from room temperature to 1000oF Figure 2.24 shows the reduction in the modulus of elasticity E for mild steel as the temperature increases As can be seen from the graph， a 30% reduction in modulus of elasticity occurs in going from room temperature to 1000oF In this figure， we also can see that a part loaded below the proportional limit at room temperature can be permanently deformed under the same load at elevated temperatures CREEP: A PLASTIC PHENOMENON Temperature effects bring us to a phenomenon called creep， which is the increasing plastic deformation of a part under constant load as a function of time Creep also occurs at room temperature， but the process is so slow that it rarely becomes significant during the expected life of the temperature is raised to 300oC or more， the increasing plastic deformation can become significant within a relatively short period of time The creep strength of a material is its ability to resist creep， and creep strength data can be obtained by conducting 7 long-time creep tests simulating actual part operating conditions During the test， the plastic strain is monitored for given material at specified temperatures Since creep is a plastic deformation phenomenon， the dimensions of a part experiencing creep are permanently altered Thus， if a part operates with tight clearances， the design engineer must accurately predict the amount of creep that will occur during the life of the machine Otherwise， problems such binding or interference can occur Creep also can be a problem in the case where bolts are used to clamp tow parts together at elevated temperatures The bolts， under tension， will creep as a function of time Since the deformation is plastic， loss of clamping force will result in an undesirable loosening of the bolted joint The extent of this particular phenomenon， called relaxation， can be determined by running appropriate creep strength tests Figure 2.25 shows typical creep curves for three samples of a mild steel part under a constant tensile load Notice that for the high-temperature case the creep tends to accelerate until the part fails The time line in the graph (the x-axis) may represent a period of 10 years，the anticipated life of the product SUMMARY The machine designer must understand the purpose of the static tensile strength test This test determines a number of mechanical properties of metals that are used in design equations Such terms as modulus of elasticity， proportional limit， yield strength， ultimate strength， resilience， and ductility define properties that can be determined from the tensile test Dynamic loads are those which vary in magnitude and direction and may require an investigation of the machine parts resistance to failure Stress reversals may require that the allowable design stress be based on the endurance limit of the material rather than on the yield strength or ultimate strength Stress concentration occurs at locations where a machine part changes size， such as a hole in a flat plate or a sudden change in width of a flat plate or a groove or fillet on a circular shaft Note that for the case of a hole in a flat or bar， the value of the maximum stress becomes much larger in relation to the average stress as the size of the hole decreases Methods of reducing the effect of stress concentration usually involve making the shape change more gradual Machine parts are designed to operate at some allowable stress below the yield strength or ultimate strength This approach is used to take care of such unknown factors as material 8 property variations and residual stresses produced during manufacture and the fact that the equations used may be approximate rather that exact The factor of safety is applied to the yield strength or the ultimate strength to determine the allowable stress Temperature can affect the mechanical properties of metals Increases in temperature may cause a metal to expand and creep and may reduce its yield strength and its modulus of elasticity If most metals are not allowed to expand or contract with a change in temperature，then stresses are set up that may be added to the stresses from the load This phenomenon is useful in assembling parts by means of interference fits A hub or ring has an inside diameter slightly smaller than the mating shaft or post The hub is then heated so that it expands enough to slip over the shaft When it cools， it exerts a pressure on the shaft resulting in a strong frictional force that prevents loosening 9 故障的分析尺寸的決定以及凸輪的分析和應用 摘要 ： 作為一名設計工程師有必要知道零件如何發生和為什么會發生故障，以便通過進行最低限度的維修以保證機器的可靠性 ； 凸輪是被應用的最廣泛的機械結構之一 ，是一種 僅僅有兩個組件構成的設備。主動件本身就是凸輪，而輸出件被稱為從動件。通過使用凸輪，一個簡單的輸入動作可以被修改成幾乎可以想像得到的任何輸出運動。 關鍵詞： 故障 高速凸輪 設計屬性 前言介紹 ： 作為一名設計工程師有必要知道零件如何發生和為什么會發生故障，以便通過進行最低限度的維修以保證機器的可靠性。有時一次零件的故障或者失效可能是很嚴重的一件事情，比如，當一輛汽車正在高速行駛的時候，突然汽車的輪胎發生爆炸等。另一方面，一個零件發生故障也可能只是一件微不足道的小事，只是給你造成了一點小麻煩。一個例子是在一個汽 車冷卻系統里的暖氣裝置軟管的松動。后者發生的這次故障造成的結果通常只不過是一些暖氣裝置里冷卻劑的損失，是一種很容易被發現并且被改正的情況。 能夠被零件進行吸收的載荷是相當重要的。一般說來，與靜載重相比較，有兩個相反方向的動載荷將會引起更大的問題，因此，疲勞強度必須被考慮。另一個關鍵是材料是可延展性的還是脆性的。例如，脆的材料被認為在存在疲勞的地方是不能夠被使用的。 很多人錯誤的把一個零件發生故障或者失效理解成這樣就意味著一個零件遭到了實際的物理破損。無論如何，一名設計工程師必須從一個更廣泛的范圍來考慮和理解 變形是究竟如何發生的。一種具有延展性的材料，在破裂之前必將發生很大程度的變形。發生了過度的變形，但并沒有產生裂縫，也可能會引起一臺機器出毛病，因為發生畸變的零件會干擾下一個零件的移動。因此，每當它不能夠再履行它要求達到的性能的時候，一個零件就都算是被毀壞了（即使它的表面沒有被損毀）。有時故障可能是由于兩個兩個相互搭配的零件之間的不正常的磨擦或者異常的振動引起的。 故障也可能是由一種叫蠕變的現象引起的，這種現象是指金屬在高溫下時一種材料的塑性流動。此外，一個零件的實際形狀可能會引起故障的發生。例如，應力的集中 可能就是由于輪廓的突然變化引起的，這一點也需要被考慮到。當有用兩個相反方向的動載荷，材料不具有很好的可延展性時，對應力考慮的評估就特別重要。 一般說來，設計工程師必須考慮故障可能發生的全部方式，包括如下一些方面： 10 壓力 變形 磨損 腐蝕 振動 環境破壞 固定設備松動 在選擇零件的大小與形狀的時候，也必須考慮到一些可能會產生外部負載影響的空間因素，例如幾何學間斷性，為了達到要求的外形輪廓及使用相關的連接件，也會產生相應的殘余應力。 凸輪是被應用的最廣泛的機械結構之一 ， 是一種僅僅有 兩個組件構成的設備。主動件本身就是凸輪，而輸出件被稱為從動件。通過使用凸輪，一個簡單的輸入動作可以被修改成幾乎可以 想象 得到的任何輸出運動。常見的一些關于凸輪應用的例子有： 凸輪軸和汽車發動機工程的裝配 專用機床 自動電唱機 印刷機 自動的洗衣機 自動的洗碗機 高速凸輪 (凸輪超過 1000 rpm 的速度 )的輪廓必須從數學意義上來定義。無論如何，大多數凸輪以低速 (少于 500 rpm)運行而中速的凸輪可以通過一個大比例的圖形表示出來。一般說來，凸輪的速度和輸出負載越大，凸輪的輪廓在被床上被加 工時就一定要更加精密。 材料的設計屬性 當他們與抗拉的試驗有關時，材料的下列設計特性被定義如下。 靜強度： 一個零件的強度是指零件在不會失去它被要求的能力的前提下能夠承受的最大應力。因此靜強度可以被認為是大約等于比例極限，從理論上來說，我們可以認為在這種情況下，材料沒有發生塑性變形和物理破壞。 剛度： 剛度是指材料抵抗變形的一種屬性。這條斜的模數線以及彈性模數是一種衡量材料的剛度的一種方法。 彈性： 彈性是指零件能夠吸收能量但并沒有發生永久變形的一種材料的屬性。吸收的能量的多少可以通過下面彈性區域內的應力圖表來描 述出來。 11 韌性： 韌性和彈性是兩種相似的特性。無論如何，韌性是一種可以吸收能量并且不會發生破裂的能力。因此可以通過應力圖里面的總面積來描述韌性，就像用圖 2.8 b 描繪的那樣。顯而易見，脆性材料的韌性和彈性非常低，并且大約相等。 脆性： 一種脆性的材料就是指在任何可以被看出來的塑性變形之前就發生破裂的材料。脆性的材料一般被認為不適合用來做機床的零部件，因為當遇到由軸肩，孔，槽，或者鍵槽等幾何應力集中源引起的高的應力時，脆性材料是無法來產生局部屈服的現象以適應高的應力環境的。 延展性： 一種延展性材料會在破裂之前表 現出很大程度上的塑性變形現象。延展性是通過可延展的零件在發生破裂前后的面積和長度的百分比來測量的。一個在發生破裂的零件，其伸長量如果為 5%，則認為該伸長量就是可延展性和脆性材料分界線。 可鍛性： 從根本上來說是指材料的一種在承受擠壓或壓縮是可以發生塑性變形的能力，同時，它也是一種在金屬被滾壓成鋼板時所需金屬的重要性能。 硬度： 一種材料的硬度是指它抵抗擠壓或者拉伸它的能力。一般說來，材料越硬，它的脆性也越大，因此，彈性越小。同樣，一種材料的極限強度粗略與它的硬度成正比。 機械加工性能（或切削性）： 機械加工性能是 指材料的一種容易被加工的性能。通常，材料越硬，越難以加工。 壓應力和剪應力 :除抗拉的試驗之外，還有其它一些可以提供有用信息的靜載荷的實驗類型。 壓縮測試： 大多數可延展材料大約有相同特性，當它們處于受壓狀態的緊張狀態時。極限強度，無論如何，不能夠被用于評價壓力狀態。當一件具有可延展性的樣品受壓發生塑性變形時，材料的其它部分會凸出來，但是在這種緊張的狀態下，材料通常不會發生物理上的破裂。因此，一種可延展的材料通常是由于變形受壓而損壞的，并不是壓力的原因。 剪應力測試： 軸，螺釘，鉚釘和焊接件被用這樣一種方式定位 以致于生產了剪應力。一張抗拉試驗的試驗圖紙就可以說明問題。當壓力大到可以使材料發生永久變形或發生破壞時，這時的壓力就被定義為極限剪切強度。極限剪切強度，無論如何，不等于處于緊張狀態的極限強度。例如，以鋼的材料為例，最后的剪切強度是處于緊張狀態大約極限強度的 75%。當在機器零部件里遇到剪應力時，這個差別就一定要考慮到了。 動力載荷 :不會在各種不同的形式的力之間不停發生變化的作用力被叫作靜載荷或者穩定載荷。此外，我們通常也把很少發生變化的作用力叫作靜載荷。在拉伸實驗中，被分次、逐漸的加載的作用力也被叫作靜載荷。 另一方面，在大小和方向上經常發生變化的力則被稱為動載荷。動載荷可以被再細分為以下的 3 種類型。 12 變載荷： 所謂變載荷，就是說載荷的大小在變，但是方向不變的載荷。比如說，變載荷會產生忽大忽小的張應力，但不會產生壓應力。 周期性載荷： 像這樣的話，如果大小和方向同時改變，則就是說這種載荷會反復周期性的產生變化的拉應力和壓應力，這種現象往往就伴隨著應力在方向和大小上的周期性變化。 沖擊載荷： 這類載荷是由于沖擊作用產生的。一個例子就是一臺升降機墜落到位于通道底部的一套彈簧裝置上，這套裝置產生的力會比升降機本身的重量大上 好幾倍。當汽車的一個輪胎碰撞到道路上的一個突起或者路上的一個洞時，相同的沖擊荷載的類型也會在汽車的減震器彈簧上發生。 疲勞失效疲勞極限線圖 如果材料的某處經常會產生大量的周期性作用力，那么在材料的表面就很可能會出現裂縫。裂縫最初是在應力超過它極限壓力的地方開始出現的，而通常這往往是有微小的表面缺陷的地方，例如有一處材料出現瑕疵或者一道極小的劃痕。當循環的次數增加時，最初的裂縫開始在軸的周圍的逐漸產生許多類似的裂縫。所以說，第一道裂縫的意義就是指應力集中的地方，它會加速其它裂縫的產生。一旦整個的外圍斗出現了 裂縫，裂縫就會開始向軸的中心轉移。最后，當剩下的固體的內部地區變得足夠小，且當壓力超過極限強度時，軸就會突然發生斷裂。對斷面的檢查可以發現一種非常有趣的圖案，如圖 2.13 中所示。外部的一個環形部分相對光滑一些，因為原來表面上相互交錯的裂縫之間不斷地發生磨擦導致了這種現象的產生。無論如何，中心部分是粗糙的，表明中心是突然發生了斷裂，類似于脆性材料斷裂時的現象。 這就表明了一個有趣的事實。當正在使用的機器零件由于靜載荷的原因出現問題時，由于材料具有的延展性，他們通常會發生一定程度的變形。 盡管許多地由于靜壓力導 致的零件故障可以通過頻繁的做實際的觀察并且替換全部發生變形的零件來避免。不管怎樣，疲勞失效有助于起到警告的作用。汽車中發生故障的零件中的 90%的原因都是因為疲勞的作用。 一種材料的疲勞強度是指在壓力的反復作用下的抵抗產生裂縫的能力。持久極限是用來評價一種材料的疲勞強度的一個重要參數。進一步說明就是，持久極限就是指在無限循環的作用力下不引起失效的壓力值。 讓我們回頭來看疲勞試驗機器。試驗是這樣被進行的：一件小的重物被插入，電動機被啟動。在試樣的失效過程中，由計算寄存器記錄下循環的次數 N，并且彎曲壓力的相應最大 量由第 2.5 方程式計算。然后用一個新的樣品替換掉被毀壞的樣品，并且將另一個重物插入以增加負荷量。壓力的新的數值再次被計算，并