內衣行業英語詞匯.doc

內衣行業英語詞匯1.Stitching / Thread線步/線1.1 Bad stitching at front pocket opening./開前袋線步差。1.2Garment were less than our standard of 9.S.P.I. / 成品的線步比要求每寸9針標準低1.3Uneven stitching of density on standard on bottom edge stitching / 褲腳線步密度不均勻。1.4Loose thread ends not removed from garment / 成品沒有剪線頭。1.5Thread ends not trimmed and should be flushed with the garment./成品線頭未剪，應該剪干凈。1.6Skipped stitches/跳線，Double stitches/重線,Broken stitches/斷線,Run off /?線落坑1.7Loose thread/松線，Thread distorted /線扭曲,1.8Needle holes or needle burns /針孔或消針1.9Part of garment caught in unrelated operation/成衣部分由無關工序所組合1.10 Improper sewing-stitching density( too loose, too tight)/線步密度不適當（太松，太緊）1.11 S.P.I. more/less than specified / 每針線步比規定多或少1.12 End of stitching not back-stitching ,tied in (securely caught in ) other seam/線步未翻針車死其它骨口。1.13 Excessive sewing thread shrinkage compare to fabric /相比布料，線的縮水度太厲害。1.14 Blind stitching were shown on top fabric/暗線外露1.15 Front pleat stitching uneven width/length 前折線步寬度或長度不均。1.16 Poor stitching on hemmed bottom /褲腳環口線步差1.17 Join stitching not in the same line/ 線步翻針位沒有在同一?位。1.18 Upper stitching tension are tighter than the lower so cause loops of fabric surface and out look. 面線間線起珠，引致線步起珠。1.19 Should be 1/4” double needle stitching at cuff ,armhole and front placket.介英/夾圈及前筒應車1/4”雙線。1.20 Broken stitching found on waistband/ 褲頭斷線1.21 Garment have uneven stitching width at front rise/前浪線步不平均。1.22 Garment not up to our stitching of 9 S.P.I. /成品未達到每寸9針的標準。1.23 Uneven stitching per inch on bottom / 褲腳每寸針數不平均1.24 Edge stitching on centre front is missing./前中欠車邊線1.25 Needle holes found below the back pocket tape/ 后袋下有針孔。1.26 Seam inside waistband is not trimmed properly and too bulky near pocket area.內褲頭子口位線頭未清及有谷位。1.27 Thread ends not trimmed/未剪線。1.29 Garment more/less than our specified 16 S.P.I./成品比我方每寸16針的標準多/少。1.30 Thread ends were not trimmed, pls trim thread ends of inside and outside garment properly before packing.線頭未剪，在包裝前請把成品內外線頭剪凈。1.31 Untrimmed bartack threads at beltloops/front pockets在耳仔及前袋位打棗線頭未剪凈。1.32 Untrimmed threads expecially at repairs and buttons./剪線不清特別在修補及鈕位。2.Waistband / 褲頭2.1 Uneven seam allowance on waistband / 褲頭子口不均。2.2 Uneven length of front opening /前開口袋長度不均。2.3 Waistband misaligned at front when buttoned / 褲頭扣鈕后前面不對稱。2.4 Very poor startover at waistband, created two rows of stitching./褲頭返針疊位欠佳，形成兩行?。2.5 Excessive startover on waistband /褲頭有過多返針。2.6 Waistband near centre back is puckering./ 后中褲頭位起皺。2.7 Puckering was found along waistband seam , it was especially poor at the top of fly front. 褲頭起皺，尤其在前鈕牌處。2.8 Poor backstitching is found on waistband/ 褲頭駁線欠佳。2.9 Uneven edge stitching on waistband /褲頭車線不均。3Placket/筒3.1 Placket top stitching not straight and balance./面筒線步不平直和對稱。3.2 Top placket not covering up completely the bottom placket/ 面筒不能全部蓋到底筒。3.3 Uneven length of sleeve placket on the same gmt/同一條成品袖筒長短不一。/ X- w; W5 g7 f# x3 z3.4 Uneven edge at front placket. 前筒反光4Interlining/樸4.1 Waistband interlining is too hard/tight./褲頭樸太緊。4.2 Should have fusible in front pocket./前袋應用樸。4.3 Should fuse fly interlining on body not fly facing./樸應用于大身內4.4 Should fuse woven fusible interlining on top centre./上中位應用樸。5.Buttons/Snap 鈕/急鈕. 5.1 Missing button at pocket month./ 袋口位欠鈕5.2 Untidy trimming at button hole./鈕門線剪線欠理想5.3 Should use X stitching on button hole./ 鈕眼位應用X 形線步5.4 Damaged button found on garments./ 成品發現壞鈕5.6 Eyelet is not clearly cut./ 鳳眼未全開5.7 Centre front closure should be used shank button instead of snap./前中應用鐵皮鈕而不用急鈕5.8 Found some garments buttons are not fastened./ 每些成品發現釘鈕不穩5.9 Button missing/欠鈕，Button damaged/壞鈕，Button misplaced/鈕錯位子， Button cracked/鈕開裂5.10Button not aligned as specified./未按規定釘鈕5.11Button insecurely sewn/buttons are not fastened/釘鈕不穩5.12Button not sewn securely preferably with lock stitch machine./用釘鈕機釘鈕不穩固，效果欠理想5.13Button not as specified size, type, color./釘鈕未按尺寸，種類，顏色等規定5.14Loose button sewing thread not clipped./打鈕線未剪5.15Button hole omitted, button hole added./未開鈕門，多開鈕門5.16Buttonhole with incomplete stitching./鈕門線步未開完5.17Buttonhole uncut./未開鈕門5.18Broken/skipped incomplete stitch in buttonhole./鈕門散/跳線5.19Buttonhole not securely caught in fabric causing stitching to pull away from fabric.鈕門未釘死在布上導致鈕門容易被拉脫. 5.20Buttonholes sewn with more/less stitches per inch than as specified./鈕門每寸針數比規定多/少5.21Defective snaps or other fasteners that do not function/work./急鈕損壞或其它扣損壞引致不能正常運作5.22Snap/Grummet are not seated properly./急鈕/雞眼不能很好地扣在一起5.23Snap that do not hold properly and released very easily./急鈕扣合不順暢.5.24Thread ends sticking out from buttonhole, its messy, should be trimmed properly before packing.鈕門線未剪，太混亂，包裝前要清理干凈5.25Buttonhole is not big enough to button or un-button, its a big tight on the garments. 鈕門太細，成品有的不夠過5.26Unclean buttonholes “ looks like knife is not sharp”./鈕門披口，鈕門刀鈍6. Pressing 燙6.1 Garments not well pressed under thigh, should be open press seam./脾開骨位沒有燙開骨6.2 Pressing on front pleat not well./前褶位燙工不好6.3 Pressing too hard and make seam shine./ 燙工不好引致起鏡6.4 Please be noted pressing on sleeve and front pocket./請留意袖和前袋的燙工6.5 Poor pressing on garments./成品燙工差6.6 Excessive wrinkle that require pressing to over come./起皺嚴重需翻燙6.7 Shine caused by improper pressing./燙工起鏡6.8 Pressed poorly at garment./燙工非常不理想7.Packing/Carton包裝/卡通箱7.1 Found C/N 18 has wrong packing. C/N 18 號箱錯包裝7.2 Wrong packing was found in C/N 18.錯包裝發現在C/N 18 號箱8. Zipper/fly拉鏈/鈕牌8.1 Poor shape of fly front./ 前鈕牌形8.2 Edge stitching at zipper uneven width./ 拉鏈車線寬窄不均8.3 Front fly stitching at lower end not well sewn./前鈕牌底部車工欠佳8.4 Zipper length on pocket facing is 1/2” shorter than size spec./袋貼的拉鏈長度比要求偏短1/2”8.5 Zipper set by stitching the fabric yielding weaving and bumpy zipper setting area.由于車工不好，導致拉鏈有起谷現象8.6 Wrong size zipper/錯拉鏈尺寸， Wrong type zipper/錯拉鏈種類， Wrong color zipper/錯拉鏈顏色8.7 Defective zipper sliders/拉鏈牙失效8.8 Defective zipper stop/拉鏈頭失8.9 Thigh clearance between the slider and the seam edge causing slider to operate with difficulty.拉鏈牙與布邊的距離太近，導致拉鏈拉合有困難8.10 Rusting in closure/拉鏈生銹8.11 Bleading in closure/拉鏈氧化8.12 Discoloration in closure/拉鏈退色，looseness in closure/拉鏈松9. Fabric defect / 布疵9.1 White point appear at fabric/ 布料出現白色點9.2 Color shade on wedding material/布邊有色差9.3 Pay attention to the fabric shrinkage manual/注意布料的縮水程度9.4 Assemble cutting with spurn-knob onto garment which should be replaced/縫合時有粒頭需更換9.5 Yarn run found on bottom of inseam/內長底發現有紗線9.6 Garment were not washed enough and too stiff/成衣洗水不足，太硬9.7 1 pc found different colored yarn at front/在前副發現1件有色紗9.8 Yarn snagged/pull yarns抽紗/絲9.9 Color shading on trim to body fabric / 副料和衫身有色差9.10Skewing on stripes. / 彎紋條9.11Bowing on stripes. /彎紋條9.12Found some garments have uneven brushing streak. / 發現某些成品有不良刷痕9.13Thick yarn粗紗,thin yarn幼紗,colored yarn色紗,broken yarn斷紗,yarn run走紗9.14Visible dye streaks / 可見染痕9.15Shade of lot different than approved sample / 與色辦顏色有色差9.16permanent crease in the fabric / 布料有死痕9.17Fabric flaws on outside garments. 成品外骨布有問題9.18Rips on the fabric. 面布有裂痕10. Color 顏色10.1Found Navy garments have color shading.發現藍色成品有色10.2Found Red garments have two different thread color. 發現紅色成品有兩種不同?色10.3Found Navy garments have two color shades after washing發現藍色成品洗水后有兩LOT色10.4Found thread of gray do not match with body color. 灰色線與衫身色不配色10.5Found type B15 fabric color is lighter than our standard. 發現B15顏色的布料比標準要淺10.6Found color Black has color shades and is lighter than our standard. 發現克色有色差，比標準要淺! 10.7Found color Mink has two color shades 發現奶白色有兩個色缸10.8Found Blue color is darker than previous shipment, and pigment washed effect has not come out. 藍色比色板偏深，沒有碧紋效果10.9Panel shading in the garments / Color shading within one garment 成品有鴛鴦色10.10 Color shading within one garment 成品有鴛鴦色10.11 Color shading piece by piece 件與件有色差11. Measurement 尺寸11.1Hip measurement wear found 1/2” smaller/larger.坐圍尺寸偏小/大1/2”11.2Back rise measurement out of tolerance 1/4” to 3/4”, should be corrected in bulk production.后浪尺寸比容忍度1/4”到3/4”，應該在大貨生產中該正11.3Bottom width 1/2” smaller than size spec, pls be careful in production not to make any smaller.腳圍寬尺寸比尺碼表偏細1/2”，生產中應改注意不可再偏細11.4Measurementdiscrepancies between sample and size spec,Bust2”bigger.辦與尺碼表的量度差別胸圍大2寸11.5Waist is inconsistent from 1” to large on some garment.腰圍1寸位不均衡，某些地方偏大! 11.6Thigh is 1”-1 1/2” large in general. 脾圍總地來講比要求的大1”-1 1/2”11.7Waist is 1/2”-1” small on some garment 某些成品腰圍尺寸偏細1/2”-1”11.8Waist is small by 3/4”.腰圍細3/4”12. Pocket 袋12.1Uneven width of pocket welt. / 唇袋寬度不均12.2Puckering on pocket flap. / 袋蓋起皺12.3Unsmooth look at front pocket. / 前袋視覺不圓順12.4Misaligned pocket. / 袋不對稱12.5Pocket size not as size spec. / 袋尺寸與標準不符12.6Poor shaped back pocket. / 后袋袋形差12.7Pocket wrong placement. / 袋錯位置12.8High-low pocket. / 高低袋12.9Found some garments back pocket uneven placement. / 發現某些成品后袋位置不均12.10 Pocket poorly shaped. / 袋形不良12.11 Pocket flap not properly placed. / 袋蓋位置欠佳12.12 Slanted pocket flaps. / 袋蓋傾斜12.13 Buttonhole at back pocket is not straight. / 后袋鈕門歪斜不直12.14 Back pocket are not aligning properly. / 后袋不成一直線12.15 Pleats formed at rivets position at front right pocket. / 右前袋撞釘位置起皺12.16 Bartack at back pockets crooked. /后袋打棗位置欠佳13Inseam內長13.1Inseam misaligned with crotch. / 十字骨位不對稱13.2Uneven length of inseam. / 內長長短14. Back Yoke 后機頭14.1Puckering was found along back yoke seam. / 后機頭起皺14.2Garments on double stitching is bit width, should be at