HT236F01-100 規(guī)格書(shū).ppt

1、1,TFT-LCD,2,3,Contents,4,HT236F01-100 is a color active matrix TFT LCD module using amorphous silicon TFTs (Thin Film Transistors) as an active switching devices. This module has a 23.6 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical pixel array). Each pix

2、el is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type.,Gate Driver,Source Driver,TFT LCD Panel 1920 1080,LVDS Rx + T/CON + Mini LVDS Tx,DC/D

3、C Gamma Vcom,Connector (CN1),LVDS Input Signal,VDD,CN22,CN23,1.2 Features LVDS Interface with 2 pixel / clock High-speed response Low power consumption 6-bit (Hi-FRC) color depth, display 16. 7M colors Incorporated edge type back-light (Four lamps) High luminance and contrast ratio, low reflection a

4、nd wide viewing angle DE (Data Enable) only RoHS /TCO 03 Compliant,1.0 GENERAL DESCRIPTION 1.1 Introduction,CN21,CN24,5,1.3 Application, Desktop Type of PC THC63LVDF83A or Equivalent) 5.2.1 LVDS Interface,12,5.4 Back-light Interface Connection,5.3 Data Input Format,Display Position of Input Data (V-

5、H),13,6.0 SIGNAL TIMING SPECIFICATION 6.1 The HT236F01-100 is operated by the DE only.,14,6.2 LVDS Rx Interface Timing Parameter The specification of the LVDS Rx interface timing parameter is shown in Table 4. ,tRIP3,tRIP4,tRIP5,tRIP6,tRIP2,tRIP0,tRIP1,Rx2,Rx1,Rx0,Rx6,Rx5,Rx4,Rx3,Rx2,Rx1,Rx0,Rx3,tRC

6、IP,Vdiff=0v,Vdiff=0v,RxCLK+,RXz +/-,* Z = 0, 1, 2,3,* Vdiff = (RXz+)-(RXz-),. ,(RXCLK+)-(RXCLK-),15,7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL 7.1 Sync Timing Waveforms,7.2 Vertical Timing Waveforms,V-Sync,H-Sync,DE,Over 3 H-sync,Fix H-Sync width Area,1) Need over 3 H-sync during V-Sync Low 2)

7、Fix H-Sync width from V-Sync falling edge to first rising edge,16,7.3 Horizontal Timing Waveforms,17,8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS,18,9.0 POWER SEQUENCE,To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below,Note

8、s: 1. When the power supply VDD is 0V, keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid., 0.5 ms T1 10 ms 0 T2 50 ms 0 T3 50 ms 1

9、sec T4 200 ms T5 200 ms T6,19,10.0 MECHANICAL CHARACTERISTICS 10.1 Dimensional Requirements FIGURE 6 (located in Appendix) shows mechanical outlines for the model HT236F01-100. Other parameters are shown in Table 5. ,10.2 Mounting See FIGURE 5. (shown in Appendix) 10.3 Anti-Glare and Polarizer Hardn

10、ess. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level

11、of 350lux.,20,11.0 RELIABLITY TEST,The Reliability test items and its conditions are shown in below. ,21,12.0 HANDLING & CAUTIONS,(1) Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module As the electrostatic dis

12、charges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back - light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of

13、 the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. (3) Cautions fo

14、r the operation When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. (4) Cautions for the atmosphere Dew drop atmosphere should be

15、 avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics Do not apply fixed pattern data si

16、gnal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. (6) Other cautions Do not disassemble and/or re-assemble LCD module. Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to

17、 be broken. We recommend to use the original shipping packages.,22,13.0 PRODUCT SERIAL NUMBER,1. Control Number 2. Rank / Grade 3. Line Classification 4. Year (2001 : 01, 2002 : 02, ),5. Month (1,2,3, , 9, X, Y, Z) 6. Internal Use 7. Serial Number,HT236F01-100,23,14.0 Packing 14.1 Packing Order,24,1

18、4.2 Packing Note Box Dimension : 233mm(W) 613mm(L) 445mm(H) Package Quantity in one Box : 5 pcs 14.3 Box label Label Size : 108 mm (L) 56 mm (W) Contents Model : HT236F01-100 Qty : Module Qty in one box Serial No. : Box Serial No. See next page for detail description. Date : Packing Date,25,Figure 1. Measurement Set Up,15.0 APPENDIX,Figure 2. White Luminance and Uniformity Measurement Locations (9 points),26,Figure 3. Response Time Testing,Where: YA = Initial luminance of measure