機床按鍵與報警顯示中英對照

1、法拉克：ALTER 修改程序及代碼INSRT 插入程序DELET 刪除程序EOB 完成一句 (END OF BLOCK)CAN 取消(EDIT 或 MDI MODE 情況下使用 )INPUT 輸入程序及代碼OUTPUT START輸 出程序及指令OFFSET儲 存刀具長度、半徑補當值A(chǔ)UX GRAPH顯 示圖形PRGRM顯 示程序容ALARM顯 示發生警報容或代碼POS 顯示坐標DGONS PARA顯M 示自我診斷及參數功能RESET返 回停止CURSOR光 標上下移動PAGE上 下翻頁數控機床中英文對照表ABS和 REL在法那克系統中，按這兩個鍵分別來切換 當前機床的相對坐標和絕對坐標ALL

2、全選，程序編輯時用PRGRM程序( program )的縮寫，用于查看程序NEXT查看程序和查看參數時，下一頁OPRT在法那克系統中，選擇編輯程序時，也就是按下 PRGRM后，再按這個鍵，才能輸入程序號HOST，CONECT這兩個是在系統與外界通信時用的， 我沒試過，不知道什么作用HELP查看幫助信息SHIFT換檔鍵，有些鍵有兩個字符，按下這個鍵，用 來輸入頂部那個字符ALTER程序修改鍵，編輯程序時用INSERT程序插入鍵，編輯程序時用EOB程序結束符，在編輯程序時，沒段程序結束時， 要加這個符號CAN取消鍵，用來取消輸入INPUT輸入鍵，用來輸入程序或參數POS按此鍵顯示當前機床位置畫面P

3、ROS按此鍵顯示當前程序畫面OFFSET 按此鍵顯示刀具偏置畫面SETTING按此鍵顯示刀具偏置設定畫面SYSTEM按此鍵顯示系統信息及系統狀態畫面GRAPH 按此鍵顯示加工時刀具軌跡的圖形畫面CUSTOM按此鍵顯示用戶宏程序畫面 手動數據輸入 (MDI) 直接數字控制方法 (DNC) 控制器單元或機控制器單元 ( MCU常見機床報警信息中英文對照T WORD ERRO（R T 碼錯誤） LOW OIL LEVEL （油位低） SPINPLE FAULT （主軸故障） SPINDLE ALARM（ 主軸報警） EXTERNAL EMG STO（P 急停按鈕被按下） AC NOT READY（

4、交流盤未準備好） SPINPLE LUBE FAULT（ 主軸潤滑故障） T CODE ERROR（ T 代碼出錯，非法 T代碼） M CODE ERROR（ M代碼出錯，非法 M代碼） SERVO NOT READ（Y 伺服未準備好） NC NOT READ（Y NC沒準備好） TURRET FAULT（ 轉塔故障） TURRET LIMIT （轉塔限位） DC 24V OPEN （直流 24 斷開） +24V NOT READ（Y +24V 沒準備好） GRAR DRIFT（ 檔位漂移）PLEASE AXIS RETURN HOM（E軸未回零） PLEASE DRUM RETURN HO（

5、M刀E庫未回零） AIRPRESSFAILUR（E氣壓故障）UNCL TOOL FAL（L 松刀失?。〢IR PRESSURE DROP（ 壓縮空氣壓力過低）CLAMP TOOL FAL（L 夾刀失?。〥RUM NOT PARK（ED刀庫未在原值）X ZERO POINT NOT REACHE（D X 軸未回零）Y ZERO POINT NOT REACHE（D Y 軸未回零）Z ZERO POINT NOT REACHED（ Z 軸未回零）4TH ZERO POINT NOT REACHE（D 第 4 軸未回零）X AXIS OVERTRAV（L X 軸超限）Y AXIS OVERTRAVL

6、（ Y 軸超限）Z AXIS OVERTRAVL（ Z 軸超限）COUNTER SWITCH REEO（R計 數開關故障）MASTERT RANSFER OVER TE（MP主 變壓器過熱）Z AXIS NOT AT FIRST REF POSITION （ Z 軸未在第一參 考點）SPINDLE ORIENTATION FALLURE（ 主軸定向失?。㏕OOL DESENT OR TOOL DATA REEO（R刀 具數據錯誤）PLEASE UNLOAD THE TOOL ON SPRINE（LK請 卸下主軸上 的刀）PLEASE LOAD TOOL ON APINDL（E 請裝上主軸上的刀

7、）A AXIS UNCLAMP FAIL （ A 軸松開失?。〢 AXIS CLAMP FAIL （ A 軸夾緊失敗）DRUM OUT TO APRONDLEIS FAL（L 刀庫擺向換刀位失 ?。㎝G SWING OVERLO（AD刀庫擺動過載）DRUM BACK PARK IS FALL（ 刀庫擺回原始位失?。㏕URRENT MOTOR1 OVERLO（A刀D 庫移動電機過載）COOLANT MOTOR OVERLO（A冷D 卻泵過載）DRUM ATC FAULT（ 自動換刀失?。㏕OOLS UNLOCKE（D 刀具未鎖緊）BATTERY ALARM（ 電池報警）DRUM POSITION

8、 SWITCH ERRO（R刀 庫位置檢測開關故 障）DRUM NOW NOT AT PAR（K刀 庫未在原始位置）IT DANGOU TO MOVE DRU（M 刀庫禁動）POT UO FAILOR POT NOT AT UP POSITION（ 刀套未在水 平位）POT DOWN FAIL（ 刀套翻下動作失?。㊣T IS DANGOUR TO MOVE ARM（ 機械手禁動）THE SPINDLE STATU IS ERROR（ 主軸狀態錯誤）ARM MOTOR OR ARM SWITCH FA（LL機 械手或機械手開關 故障）CENTRE LUBRICATION FALL（ 中心潤滑故障

9、）THE WORK NOT CLAMPE（D工 件未夾緊）AUTO TOOL CHANGE FAUL（T自 動換刀失敗）TOOL DATA OUT OF RANG（E 指令刀具號超出圍）THE ORDER TOOL NOW IN SPINDL（E 目標刀具在主軸 上）THE THREE SPINDLE SWITCH FAUL（T 主軸上的接近開 關）THE CENTRE COOLANT IS LOWE（R刀 具冷泵液位過低）DRUM RETURN 1# POSITION FAUL（T 刀庫自動回零失 ?。㏒PINDLE OVERLOA（D 主軸過載）TURRENT MOTOR OVERLO（A

10、刀D 盤轉動電機過載）CHIP CONVEYER OVERLOA（D拉 屑器過載）HARD LIMIT OR SERVO ALARM（ 硬限位或伺服報警）NO LUB OIL （無潤滑油）INDEX HEAD UNLOCKE（D 分度頭未鎖緊）MT NOT READ（Y機床沒準備好）MG OVERLOA（D 刀庫過載）LUB EMPT（Y 潤滑無油）AIR PRESSUR（E 氣壓不足）COOLANT NOT REA（DY冷卻沒準備好）LUBE EMPT（Y油霧油位低，潤滑油位低）LUB PRESSURE LO（W潤滑壓力低）CONVEY VERLO（AD排屑過載）LUB OVERLOA（D潤

11、滑過載）LUBE PRESSURE LO（W油霧壓力低）SERIAL SPINDLE ALARM （串行主軸報警 ）NC BATTERY LOW ALARM（N電C池低報警 ）MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERRORMAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALAR氣M（壓低報警 ）MOTOR OVERLOA電D機（ 過載 ）T CODE MAGAZINE TOOLST CODE 1 ERROR5TH AX

12、IS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED開（門 ）LUB PRESSURE SWITCH ERRO油R壓（ 開關錯誤 ）SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORM（AL主軸負荷異常）TRANSDUCER ALA（RM傳感器報警）BED-HEAD LUBRICATE OF（F床頭潤滑關閉）EMG OFFHYDRAULIC CHUCK PRESS L（O液W壓夾頭壓力低）HYDRAULIC TAIL PRESS LO（W液壓尾座壓力低）LUB 0IL LOW（油壓低）TURRET COD

13、E ERR（OR轉塔碼錯誤）TURRET RUN OVERTIM（E轉塔運行超時）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFT

14、ER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（ X 軸被鎖定）Y AXIS IS LOCKED（ Y 軸被鎖定）Z AXIS IS LOCKED（ Z 軸被鎖定）A AXIS IS LOCKED（ A 軸被鎖定）SPINDLE MOTOR FAN QF26 OF主F（軸電機風扇 QF26關閉 ）SPINDLE ORIENTATION INCOMPLE（TE主軸定位不完全）M FUNCTION NOT COMPLE（TEM 功能無法完成）SPINDLE NOT IN GEAR POSITION（齒輪不在主軸位置）SP

15、INDLE NOT CHANGED TO LOW G（EA主R軸沒有變?yōu)榈?檔）SPINDLE NOT CHANGED TO HIGH GR（A主R 軸沒有變?yōu)楦?檔）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,MAG.JOG SWITCH ONHYDRAULIC MOTOR

16、 QF7 O（FF 液壓馬達 QF7關閉 ）HYDRAULIC TEMPRETURE H（IGH液壓使用溫度高 ）HYDRAULIC FILTER BLOCKE（D液壓過濾器阻止）HYDRAULIC OIL LEVEL LOW（ 液壓油位低 ）HYDRAULIC FAN QF8 OF（F液壓風扇 QF8關閉）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 O（F冷F 卻液電機 QF12關閉）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT B

17、LOC（K冷卻堵塞）SPINDLE COOLANT MOTOR QF14 O（F主F 軸冷卻液電機 QF14關閉）INNER COOLANT QF13 OF（F冷卻液 QF13關閉）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LO（W低氣壓）SPINDLE COOLANT MOTOR FAU（L主T 軸冷卻液電機故障）LUB.OIL IS LOW （潤滑油低）DOOR OPE（N門打開）FRONT DOOR（R） OPE（N前門打開）LEFT DOOR OPE（N左門打開）LUB

18、RICATION OIL QF23 OFF（潤滑油 QF23關閉）LUBRICATION PRESS LO（W潤滑油位低）IN ADJUST,MAG CANT EXCHANGE（ T在調整，刀庫不能 交換 T）NOT ALL DOOR CLOSE（D門沒有全部關閉）IN M06,MAG NOT READ（Y 在 M06，刀庫未準備好） MAGAZINE NOT READ（Y刀庫未準備好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE

19、 ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZNOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG

20、 FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 設定 D499 為 0K PARAM ABOUT MAG SET IS WRON關G于 MAG的 K 參數設 定錯誤MECHANICAL BRAKE NOT RELEAS機E床D 抱閘沒有松開 MECHANICAL BRAKE IS WRON機G床 抱閘錯誤PLEASE ADD LUB.OIL 請加潤滑油PROBE BATTERY VOLTAGE IS LO探W頭 電池電壓低PROB

21、E IS ERR 探頭錯誤PARAMETER WRITE ENAB（L參E 數寫使能）PMC EDIT ENABL（E PMC編輯使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS主 軸檔位信號消失 T_CLAMPED_SIGNAL MISS 夾T 緊信號消失SP OVERRIDE SWITCH DISCONNECTIO主N軸 倍率開關斷路 FEED OVERRIDE SWITCH DISCONNECTI進ON給 倍率開關斷 路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO A因IR

22、為 缺少壓空交換停 止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE冷 卻水少立即加水COOLANT LEVEL LOW,ADD COOLANT WA冷TE卻R水 液位低PLEASE REPLACE CNC BATTERY QUICK請LY立 即更換 CNC 電池SIEMENS常用縮略語A Output 輸出ASCII American Standard Code for Information Interchange 美國信息交換標準代碼AV Preparation for work運行準備BA Operating mode 運行方式B

23、AG Operating mode groups 運行方式組BB Ready for operation準備好運行BCD Binary Coded Decimals 二- 十進制BHG Hand-held terminal 手提終端BOF User interface用戶接口CNC Computerized Numerical Control計算機化數字控制CP Communication Processor 通迅處理器CPU Central Processing Unit計算機中央處理裝置CR Carriage Return 托架折回CSB Central Service Board(PLC

24、 module)中央維護板，PLC 模塊CTS Clear To Send 發送使能數模轉換器DAU Digital-Analog ConverterDB Data Block 數據塊DIN German Industrial Standards德國工業標準DIO Data Input/Output 數據輸入 / 輸出DRF Differential Resolver Function差分功能DRY Dry Run 空運行DSB Decoding Single Block譯碼單段DSR Data Send Ready 備用輸入DW Data Word 數據字E Input 輸入EIA-Code

25、 Special tape code,number of holes per characters always odd特殊紙帶碼，每個字符的孔數為奇數EPROM Programm memory with fixed program 有固定程 序的程序存儲器E/R Controlled Supply and Energy Recovery Module 可控電源和能量恢復模塊ETC ETC key:Extension of the softkey bar in thesame menuETC 鍵：同級菜單擴展鍵FDB Product designation database 產品指定數據庫FI

26、FO First in First Out 先進先出FRA Frame module 幀頻模塊FRAME Coordinate conversion with the components zerooffset ， rotation ，scaling ， mirror-imaging 坐標換算，具有零點偏置，坐標旋轉， 標度功能和鏡向功能FRK Cutter radius compensation 銑刀半徑補償FST Feed Stop 停止進給GUD Global User Data 全體用戶數據HMS High-Resolution Measuring System 高分辨率測量 系統HS

27、A Main Spindle Drive 主軸驅動HW Hardware 硬件IM Interface Module接口模塊IM-S/R Interface Module(S=send/R=receive)接口模塊， S=發送/R=接收INC Increment 步進增量ISO-Code Special tape code,number of holes per character always even特殊紙帶碼，每個字符的孔數為偶數K1.k4 Channel 1 to Channel 4通道 1 到通道 4KOP Ladder Diagram 梯形圖KV Loop-Gain Factor

28、增益系數KUE Transformation Ratio傳動比液晶顯示LCD Liquid Crystal DisplayLED Light Emitting Diode發光二極管顯示LUD Local User Data 局部用戶數據MB Megabyte 兆字節MD Machine Data 機床數據MK Measuring Circuit測量回路MDA Manual Data Automatic 手動輸入，自動執行MLFB Machine-readable product designation機器可識別的產品代號MMC Man Machine Communication:User in

29、terface ofthe numerical controlsystem for operation,programming and simulation 人機通訊：系統操作界面，用操作，編程和模擬MPF Main Program File ： NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多點通訊接口MSTT Machine control panel 機床控制面板NC Numerical Control 數字控制NCK Numerical Control Kernel(numerical krnel w

30、ith block preparation,數字控制核心：具有程序段預traversing range etc.) 處理, 運行圍等等NCU Numerical Control Unit 數控單元NURBS Non Uniform Rational B Spline非均值有理 B樣條NV Zero Offset 零點偏置OEM Original Equipment Manufacturer 原設備制造商OP Operator Panel 操作面板OPI Operator Panel Interface操作面板接口PC Personal Comprter 個人計算機PCMCIA Personal Computer Menory CardInternational Association 接口協議PG Programming Device 編程器PLC Programmable Logic Control 可編程邏輯控制器PRT Program Test 程序測試RAM Random Access Memory 隨機存取存儲器RISC Reduced Instruction Set Computer 處理器，具 有指令組小、通過能力強ROV Rapid Override 快速修調RPA R Parameter