減速器參數表格

1、B.4 Gear reducer data sheet加速器數據表Man ufacturers are recomme nded to use this form below whe n providi ng gear reducer in formati on.在提供減速器信息的時候，推薦制造商采用如下的表格Manufactured by 制造商:Date submitted 提交日期Nominal reducer size 額定減速器尺寸 Calculated Values 計算值Pitti ng resista nee torque 抗孔蝕性扭Units 單位： Static torqu

2、e 矩靜態扭矩Units:3First reduction 級減速 First reducti on: 級減速Second reduction 二級減速 Gear大齒輪Pinion小齒輪 Third reduction 三級減速Second reducti on:二級減速Bending strength torque 彎曲強度扭矩Units:GearPinionFirst reduction 級減速:Third reduction:三級減速Gear Pinion Gear PinionSecond reducti on:GearPinion Third reducti on:Gear Pini

3、onNotes:1. First reduction is high-speed reduction.一級減速時高速減速2. Second reduction is slow-speed reduction on double reduction gear reducers and the intermediate reduction on triple reduction gear reducers.二級減速時雙級減速器的低速和三級減速器的中級減速。3. Third reduction is the slow-speed reduction on triple reduction reduc

4、ers and is not applicable ondouble reduction reducers.三級減速是指三級減速器的低速減速，不適用于雙級減速。Con structi on Features結構數據Type of reducer (Cross out if not applicable) 減速器的類型(不接受交叉式)(Single)單級(Double)雙級仃riple) Reduction 三級(Sin gle)(Double)Helical geari ng螺線Teeth齒輪齒Number of teeth and normal diametral pitch or tran

5、sverse diametral pitch:齒輪齒數量和額定徑節或是橫向徑節距First reduction 級減速NpNgPnd PdSecond reduction二級減速 NpNgPnd PdThird reduction 三級減速 Np Ng Pnd PdCen ter dista nee and net face width:中心距和凈面寬度First reduction Cs, WSecond reducti on Cs, WThird reducti on Cs, WfFigure B.3 - Manufacturer s gear reducer data sheetHeli

6、x an gle and no rmal pressure an gle or tran sverse pressure an gle (degrees):螺旋角和常規壓力角或橫壓力角(度)First reduction 也 n, tSecond reduction 也 n, tThird reduction 山 n, tGeometry factors, I a nd J (for pi nio n and gear)幾何因數 I 和 J(對于小齒輪和齒輪)First reduction geometry factor 一級減速幾何因數 I Cj,pCj,gSecond reduction

7、geometry factor 二級減速幾何因數 I Cj,pCj,gThird reduction geometry factor 三級減速幾何因數 I Cj,pCj,gManufacturing methods 制造方法Teeth gen erated by 齒輪齒生產 process 程序 Teeth fini shed by 齒輪齒拋光 processTooth hardening method 齒輪齒的硬化方法 Gear and pi nio n materials and hard ness齒輪和小齒的材料和硬度First reducti on 級減速Gear material 齒

8、輪材料Surface BHC/Rc 表面Core核心 BNH aPinion material Surface BHC/Rc Core BNH aSecond reduction 二級減速Gear material Surface BHC/Rc Core BNH aPinion material Surface BHC/Rc Core BNH aThird reducti onGear material Surface BHC/Rc Core BNH aPinion material Surface BHC/Rc Core BNH aOther components 其他部件Cran ksha

9、ft material曲軸材料Hardn essHousing material 箱體材料Housing type (Check ): 箱體類型Split 裂口 One piece 單片Bearing sizes b軸承尺寸 Bearing loading d軸承載荷High speed pinion 高速小齒輪High speed pinion 高速小齒輪In termediate speed pi nio nc中速小齒輪In termediate speed pi nio nc 中速齒輪 Low speed pinion 低速小齒輪Low speed pinion Low speed ge

10、ar 低速齒輪 Low speed gear a Core hardness required for surface hardened gears and pinions only.核心硬度要求b For journal bearings indicate projected area; for roller bearings indicate the American BearingManufacturer s Association (or equivalent)經向軸承指投影面積，滾子軸承指美國軸承制造協會尺寸(或是相等的)size. List all bearings on each shaft. (State if bearings are mounted in carriers or directly in gear housing.)列岀每一個軸的軸承。c Not applicable on double reduction reducers.不接受不是雙級減速d For journal bearings, list