卡萊特發送卡設置步驟(The T7 Send Card)

1、發送卡-T7卡萊特同步發送卡T7，是一款專業用于LED同步顯示的發送卡，他具有分辨率自適應的功能，一張T7發送卡可控制130萬點的LED顯示屏（列數最大2048點，行數最大1024點），如超過可級聯發送卡。配合DVI接口或者HDMI接口的獨立顯卡來使用。本文重點講述設置發送卡的步驟。一、 發送卡連接圖發送卡連接拓?fù)鋱D（01）二、 硬件結構發送卡端口定義圖（02）1. 供電（5V/2A）w 方法一：通過PCI供電：將T7發送卡的金手指插入電腦空的PCI插槽內；w 方法二：外接5V電源到T7發送卡的大4Pin電源插座上。發送卡紅色指示燈常亮表示5V電供電正常。2. 連線w 用DVI線把T7發送卡與

2、顯卡連接在一起，用于傳輸圖像數據；w 用USB串口線將T7發送卡串口與電腦USB口相連，用于設置發送卡的程序；（注：首次需要安裝串口驅動，可以在安裝好卡萊特LED控制系統軟件：LEDShowT9或LEDVISION后，在安裝目錄下找到“PL-2303 Driver Installer.exe”并安裝這個文件）w 用網線將T7發送卡與接收卡相連，用于控制接收卡及大屏。（注：發送卡到接收卡以及接收卡之間的連接線為超五類或者六類的網線，水晶頭的壓制為國標568B的線序；）三、 顯卡設置1顯卡型號目前市場上主流的顯卡有二大系列：NVIDIA的MX系列（400、440、5200等型號）；ATI的鐳(RA

3、DEON)系列（4670、5550、7000、7500、8500、9000等型號）。正確安裝相對應的顯卡驅動。2設置NVIDIA顯卡1) 首先我們要打開顯卡設置界面：右鍵電腦桌面空白處，在如下圖的菜單中選擇【NVIDIA控制面板】：如果如下圖所示沒有【NVIDIA控制面板】，我們也可以點擊【屬性】,在【顯示屬性】對話框，點擊【設置】，選擇合適的顯示器分辨率，再點擊【高級】按鈕，如下圖所示：然后在彈出如下圖的界面中，點擊“GeForce”在如下圖的界面中點擊【啟用NVIDIA控制面板】，也可以打開顯卡設置的界面2) 在【NVIDIA控制面板】中選擇【設置多個顯示器】，再選擇【復制模式】，點擊【應

4、用】按鈕即可。3 設置ATI顯卡1) 首先要打開顯卡設置界面，其操作方式與打開 NVIDIA設置界面雷同。2) 在如下圖的ATI控制面板中，選擇【顯示器管理器】，右擊模擬顯示器2，點擊【啟用】，選擇【復制模式】，點擊【應用】，【確定】。 3) 出現如下圖的界面即可點擊【確定】，完成ATI的顯卡設置。四、 設置發送卡參數1、控制界面打開卡萊特控制系統軟件，點擊【控制屏幕】-【屏幕管理】，選擇【發送卡發送】，密碼【168】，如下圖【屏幕管理】界面。2、發送卡分辨率設置點擊【分辨率設置】，發送卡默認分辨率為1280x1024，9.9版本的支持自適應分辨率，可以點擊【設置為當前顯示器的分辨率】，也可在

5、【發送卡分辨率】的下拉菜單中選擇與當前顯示器一樣的分辨率點擊【設置】如圖所示。點擊【設置】或者【設置為當前顯示器的分辨率】后，會出現如下圖所示的進度界面。發送完成后，軟件會提示【發送成功，請斷電重啟發送卡！】，注：發送卡斷電重啟后，需再次進行本文第三節的顯卡設置步驟。3、串口選擇用USB串口線將T7發送卡串口與電腦USB口相連，用于設置發送卡的程序，當串口通信正常時，軟件的屏幕管理界面串口狀態會出現如下圖所示【找到發送卡，可以設定參數】。（注：首次需要安裝串口驅動，可以在安裝好卡萊特LED控制系統軟件：LEDShowT9或LEDVISION后，在安裝目錄下找到“PL-2303 Driver I

6、nstaller.exe”并安裝這個文件）4、探測接收卡用來檢測接收卡能否正常通訊（或觀察接收卡綠燈有沒快閃）。若是探測不到接收卡或者所探測出的接收卡的數量與實際不符，請檢查接收卡是否已正常通電或網線是否接觸良好。正確的操作如下圖所示：5、網口控制面積設置根據LED顯示屏的大小選擇網口控制面積如圖（a），然后【發送】到發送卡。若顯示屏比較大，需要使用雙網口，可以使用自定義模式，例如顯示屏（1344*672），設置網口如圖（b），然后【發送】到發送卡。（a） （b）網口控制面積設置以上為設置發送卡T7的全部步驟！The T7 Send CardColorlight synchronou

7、s send cards - T7, is a professional send card for LED synchronized display, with the function of adapting resolution automatically.  One T7 send card can control the LED display with 1.3 million pixel(maximum columns is 2048points, maximum 

8、;lines is 1024 points), if over the maximum, the send cards can be cascaded，and used with DVI or HDMI graphics card. This article focuses on the steps of setting send cards.一、 Connection Diagrams of Send Cardtopological connection diagrams of send card二、Hardware structureSend car

9、d port defined1.Power supply( 5V/2A)w Method 1: Supplied by PCI : put the T7 send cards goldfinger into the empty PCI slot of the computer;w Method 2: Connect 5V external power supply to the bigger 4-PIN power Socket on the T7 sen

10、d card.The red indicating lamp on the sending card work steadily, indicates the 5V power supply works well.2.connectionw Connect T7 send card with graphics card, by a DVI cable, for transmitting image dataConnect T7 send card serial port with the computers serial port, by a USB serial cable, fo

11、r setting program to the send card.w （Note: for the first time, need to install the serial driver. After install the Colorlight LED control system software: LEDShowT9 or LEDVISION, the "PL-2303 Driver Installer.exe" can be found in installation directory and install this file）w Connect T7

12、send card with receive card, by a network cable, for controlling the receive card and the screen（Note: the connecting cables between send cards and receive card, and the cables among receive cards are UTP cable or category six cable, the network cable plug comply with the line order of 568B internat

13、ional standard）三、Graphics card settings1.Graphics card modelCurrently, there are two mainstream graphics cards series on the market:NVIDIA's MX Series (model 400, 440, 5200 etc.ATI's RADEON Series (Model 4670, 5550, 7000,7500,8500,9000 etc.)Install the corresponding graphics card driver corr

14、ectly.2.ATI graphics card settings1)First, we open the graphics card setting interface: Right-click the space on desktop, select ATI Control Panel in the menu, just as the following image showsIf there is no ATI control panel in the menu, we can also click on Properties, as the following imageIn the

15、 Display Properties dialog box, click the Setting, select the appropriate display resolution, and then click Advanced button, as shown below:Then, click the ATI . in the interface, as following shown In the interface, click the ATI Catalyst Control Center as following image shows, also can open the

16、graphics card settings interfaceIn the ATI control panel, select Monitors Manager, as following image shows, then right-click simulate monitor 2, click Enable, select Copy Mode, and click Application, OK.The interface as shown in below image appears, click OK to finish the ATI graphics card setting.

17、3.(NVIDIA graphics card settings)1)First, open the graphics card setting interface, and its operation is similar to opening ATI setting interface2) In the NVIDIA Control Panel, select set up multiple monitors, and then select Copy Mode, click Application button.四、Set send cards parameters1.Control i

18、nterfaceOpen Colorlight control system software, click Control screen - Management screen, select the Send card send, passwords, 168, just as the following image of Management screen interfaceAuto COM SelectionNet Port Control Area SettingDetect Receiving cardSet Send Card ResolutionSet Display Area

19、 Location and SizeLoad or Edit Configuration Parameters2、send card resolution setting Click resolution settingSend cards default resolution is 1280x1024, 9.9 version send card support the function of adapting resolution automatically., click set to the current display resolution, also can select the

20、 same resolution to current display, in the drop-down menu of send card resolution and click set, just as following image shows.After click set or set to the current display resolution, it will appear the progressing interface, as show belowAfter the transmission, the software will prompt send succe

21、ssfully, please power off the send card, and restart! Note: After restart the send card, need to do the steps of graphics card setting again, in Chapter III of this article3. Serial ports choiceConnect T7 send card serial port with the computers serial port, by a USB serial cable, for setting t

22、he program to the send card. When the serial ports communicates well, the status of serial port, in the softwares management interface, will be just as below image shown found to send cards, can set parameters （Note: For the first time, need to install the serial driver

23、. After install the Colorlight LED control system software: LEDShowT9 or LEDVISION, the "PL-2303 Driver Installer.exe" can be found in installation directory and install this file）4. Detecting receive cardFor testing whether the receive card communicate well (or observe whether the green lamp on receive card flash quickly). If detect no receive card,&