頂針安裝流程

1、半潤安盎與您擇手改樂生遼無錫華潤安盛科技有限公司ESEC & ASM頂針安裝流程/The procedure fixing needleof ESEC and ASMWuXi China Resources Micro-Assembly Technology Co.,LTDESEC 頂針安裝流程/The procedure fixing needle of ESEC羽閃« « ®手改少生活1 工夾具準備/Preparing the jig and tools頂針/Needle開口扳于或活動扳于/Ringent wrench or monkey wrench

2、夾具/Jig頂針座/Needle holder頂針帽/pepper pot2頂針選取/Selecting needle100um200um娶悠K手改妙?；?頂針安裝/Fixing the needle1 將頂針座放入匚夾具定位孔中 /Plug the needle holder in the jig2 轉動把于固定頂針座/Fix the needle holder with gripe3 旋松頂針座的緊固螺帽/Screwthe nut with wrench6個定頂針/Fix the needle4安裝頂針/Plug the needle in the needle holder5調整頂針高度

3、（注意：頂針針尖必須 頂在夾具表面，頂銷端面必須和夾具 表面貼合）/Adjust the height .The needle and the pin must be pushed against the side of the jig娶悠&手改妙?；?安裝頂針座/Fixing the needle holder帶有三個卡槽的頂針基座/The ejector with 3 slots安放頂針在頂針基座上/Plug the needle holder in the ejector安裝頂針時要將頂針座上的銷釘卡在 基座的卡槽中，然后稍稍用力向下按 緊/Push the he needle

4、holder to make sure the pin be locked by the slot, then press out.娶悠K手改妙?；顑煞N頂針帽/Two kinds of pepper pot安裝頂針帽/Put on the pepper pot安裝頂針帽時向下按緊使卡槽卡住銷 釘/Press out the pepper pot to make the slot lock the pin5安裝頂針帽/Fixing the pepper pot脳劭hi手at » 4=活安裝完成/FinishASM頂針安裝流程/The procedure fixing needle of

5、 ASM«手改妙?；? 工夾具準備/Preparing the jig and tools緊固螺母/Nut夾具/Jig開口扳于或活動扳于頂針帽/pepper pot頂針座/Needle holder/Ringent wrench or monkey wrench2頂針選取/Selecting needle100um200um娶悠K手改妙?；?頂針安裝/Fixing the needle2 安裝頂針/Plug the needle in the needle holder1 將頂針座安裝在夾具定位銷 上，旋松緊固螺母/Put the needle holder on the pin o

6、f the jig,then unscrew the nut娶悠K手改妙?；? 用開口扳手或活動扳 手旋緊緊固螺母，固定 頂針/Fixing the needle with wrench3調整頂針高度（注意：頂針針 尖必須頂在夾具表而，頂銷端 面必須和夾具表面貼合。） /Adjust the height. The needle and the pin must be pushed against the side of the jigwM悠&手改妙?；?安裝頂針座/Fixing the needle holder帶有定位銷的頂針基座/The ejector with pin安裝頂針在

7、頂針基座上。（頂針座的卡 槽要卡在基座定位銷上，然后用力向下 壓緊）/Plug the needle holder in the ejector,make sure the slot lock the pin of the ejector ,then press out娶悠&手改妙?；?安裝頂針帽/Fixing the pepper pot安裝頂針帽（使頂針帽上的卡 槽卡住定位銷，向下按緊）/Put on the pepper pot Press out the pepper pot to make sure the slot lock the pin用2.0的六角扳手旋緊緊固頂絲/S

8、crew the bolts with wrench to fix the pepper pot娶悠K手改妙牛活When finished the changing, please do the “Teach Z-height5 頂針更換好之后，必須定義頂針的初始高度。1. 1. For ESEC2007 the menu is "Assist - Pick & place tools : Needle up /Needle down / Define needle”.對于ESEC2007按照菜單：“ “Assist - Pick & place tools : Ne

9、edle up / Needle down / Define needle”.來定義頂針初始高度。2. 2. For ESEC2008 the menu is "Teach 一 Pick & Place 一 Extended pickup process: Teach Z-heightn.對于ESEC2008按照菜單 “Teach - Pick & Place - Extended pickup process: Teach Z-heightn.設備會自動校正頂針高度。3. 3. For ASM AD828 the menu is "Set up 一 Pick & Place 一 Ejector Posns： Ref對于ASM AD828按照菜單 “Set up 一 Pick & Place 一 Ejector Posns： Ref ”來定義 頂針初始高度。4. 4. For ASM AD889 the