CTL_DECISION_重測導則(中英文對照)

1、CTL PROVISIONAL DECISION SHEET關于CTL的臨時決定Standard(s)-(year and edition)規格:IEC 61215-2005 ED.2IEC 61646-1996 ED.1Sub clause(s)替代條款:See individual items看個別條目Sheet n0 :PDSH 647Subject主題:Retest Guidelines for IEC61215 and IEC61646重測導則Key words主題詞:PV module, modifications,Retest guidelines光伏組件，更改，重新測試To b

2、e approved by the 45th CTL Plenary Meeting2008經2008年第45次CTL全體會議上批準Question:問題：How should a certified PV module be evaluated after changes are made to its design,materials, components or process in order to maintain its certification to IEC 61215/IEC 61646?當改變了已經認證過的光伏模塊的設計，材料，元件或工序后，如何進行評估來保持其認證？Dec

3、ision:決定：This Decision Sheet sets forth a uniform approach to maintain the certification of PVModules that have, or will, undergo modification from the articles originally certified.這一決定表提出了統一的辦法，來保持已經或?qū)脑瓉碚J(rèn)證的文章中接受改造的光伏模塊的認證。Changes in material selection, components and manufacturing process can imp

4、act electrical performance and reliability of the modified product. Those products meeting the requirements of the relevant standards after retesting are considered to be compliant and will be issued an amended CB Conformity Assessment Certificate and an Amended Test Report.原材料選擇、元件和制造過程中的變化，可能會影響電氣

5、性能，改良產品的可靠性。產品會議認為，在重新測試后，相關標準的要求是兼容的，會發出經修訂的立法會CB符合性評估證書和修訂的測試報告。The number of samples to be included in the retesting program and the pass/fail criteria is to be taken from the standard originally used to certify the product (either IEC 61215 or IEC 61646).重測程序包括樣本數目，通過/失敗的標準是采用原來的標準來認證該產品。This do

6、cument is organized by major modification headings and specific supporting examples. Following this is the recommended retesting sequence with parenthetical reference to the specific clauses of the relevant IEC standards.本文件由主要修改的標題和具體支持的例子組成，以下是建議復檢順序，括號內是供參考的有關IEC標準的具體條文。For the modifications list

7、ed below, the Qualification Approval tests in IEC 61215 and IEC 61464 shall be used as a guideline by the National Certification Body (NCB), Certification Body Testing Laboratory (CBTL)and assessors.對于下面列出的修改，在IEC 61215和IEC 61464資格檢定測試中，被國家認證機構（協調機構） ，認證機構的測試實驗室（CBTL）和評審用來作為指引。Any change in the desi

8、gn, materials, components or processing of the module may require a repetition of some or all of the qualification tests to maintain type approval. Each sample of the modified module shall be subjected to preconditioning and then checked against the STC power rating on the label.在設計，材料，部件或處理組件方面的任何改

9、變，可能需要資格測試中部分或全部的重復，以保持類型批準。每個所修改的模塊樣品應受到預先處理，然后檢查標簽上的STC計算額定功率。The following list provides guidance as to which tests should be repeated.下面的列表提供了重新測試的指導。Note 1: Tests 10.1,10.2,10.3 and 10.15 shall be performed before and after the specific tests listed below.注1：測試10.1,10.2,10.3和10.15，應執行以下列出的之前和之后

10、的具體測試。Note 2: In case of IEC 61646 approval test: Specifics for thin film cell changes are under consideration; Final light soaking (10.19) test is compulsory for all test samples.注2：關于IEC 61646鑒定試驗：相關薄膜電池的一些特殊要求正在考慮中;最后的曝曬（ 10.19 ）試驗對所有的測試樣本是強制性的。a) Changes in Cell technology電池片工藝變更For modification

11、 such as： Metallization materials and /or process金屬化材料(柵線材料)和工藝 Anti-reflective coating process減反射鍍層膜 Type of diffusion layer material擴散工藝的類型 Semiconductor layer material半導體層材料 Order of cell process if the change involves the metallization system金屬工藝順序的要求，如果改變涉及金屬化系統 Change of manufacturing site of

12、the solar cells not under the same QA system 生產地發生變化且不在原來的QA系統 Use of cells from a different manufacturer 來自不同制造商的電池片 Major reduction in cell thickness (greater than 25%for cell thickness200µmand greater than 17.5% for cell thickness 200µm) 厚度大于200um電池片厚度減少超過25%。厚度小于等于200um電池片厚度減少超過17.56%厚

13、度。Repeat:重做 Thermal cycling,200cycles (10.11) 熱循環試驗 Damp heat(10.13),may be omitted if outer surface of cell is chemicallyidentical (metallization and AR coating) 濕-熱試驗，如果電池片的外層材料沒有更改可以不做濕熱測試。 Hot spot endurance (10.9) 熱斑耐久試驗 Mechanical Load test(10.16) for reduction of cell thickness only機械載荷試驗，只針對

14、電池片厚度的減少的情況下做此測試。b) Modification to encapsulation system封裝系統變更For modification such as: Different materials不同材料 Different additives不同添加劑 Different encapsulation process e.g. curing rate封裝工藝的變更，如固化速度變更Repeat:重做 UV(10.10)/thermal cycling,50 cycles(10.11)/humidity freeze sequence(10.12) 紫外預處理試驗/熱循環試驗，5

15、0循環(10.11)/ 濕凍試驗(10.12) Damp heat(10/13) 濕-熱試驗 Hail impact (10.17) if not tempered glass冰雹試驗（如果不是鋼化玻璃） Hot spot (10.9) if material composition changes熱斑耐久試驗（如果材料成分更改）c) Modification to superstrate面板變更For modification such as: Different material不同材料 Different thickness, reduced by more than 10%厚度減少10

16、%以上 For glass, if there is a reduced in the head strengthening process (for example,if a change is from tempered glass to heat strengthened or annealed) 熱處理工藝不同的玻璃（如鋼化玻璃改成熱加強或退火玻璃） Different surface treatments, adhesives or primers if they are in direct contactwith encapsulate material不同表面處理（如果粘合劑或底

17、層漆與封裝材料直接接觸） If the change if from glass to non-glass or vice-versa, it should be considered a new product altogether如果從玻璃改非玻璃或反之，則應該被看成是全新的產品）Repeat:重做： UV (10.10)/ thermal cycling,50cycles(10.11)/ humidity freeze(10.12) sequence紫外預處理試驗50次熱循環試驗濕凍試驗 Mechanical load test (10.16) 機械載荷試驗 Hail test (10.

18、17) 冰雹試驗 Damp heat (10.13) (if non-glass) 濕-熱試驗 Hot spot (10.9) for non-glass if material changes or thickness is reduced熱斑耐久試驗（如果面板不是玻璃了，或者厚度減少了） Outdoor exposure (10.8) if change in material室外曝露試驗（材料的更改）d) Increase in module size組件尺寸的增加 For increase by more than 20% of length or width長和寬增加20%以上Rep

19、eat: Thermal cycling,200 cycles (10.11) 熱循環試驗 Mechanical load (10.16) 機械載荷試驗 Hail impact (10.17) (for size increases of more than 50%)冰雹試驗（總面積增加超過50）e) Modification to backsheet /substrate背板變更For modifications such as: Different material不同材料 Reduction of thickness of more than 20% 厚度減少20%以上 Differen

20、t additives, surface treatments, adhesives and primers不同的附加物，表面處理，粘合劑或底層漆Repeat: UV (10.10)/thermal cycling, 50 cycles (10.11)/ humidity freeze(10.12) sequence紫外預處理試驗50次熱循環試驗濕-凍試驗 Robustness of terminations (10.14) 引出端強度試驗 Damp heat (10.13) (if non-glass) 濕-熱試驗（針對非玻璃） Hail impact (10.17) if rigidity

21、 depends on the backsheet冰雹試驗 Mechanical load (10.16) if mounting depends on the backsheet/ substrate機械載荷試驗（如果安裝需要背板或者面板的支撐）If there is a change from substrate design or from substrate to superstrate design , the entire qualification test sequence in IEC 61215 shall be conducted. 如果從面板到背板同時更改，全部重測。f

22、) Modification to frame and/or mounting structure邊框和安裝結構變更For modification such as: Cross section of frame邊框截面 Different framing material邊框材料 Different mounting technique安裝方式Repeat: Mechanical load test (10.16) 機械載荷試驗 Outdoor exposure (10.18) if plastic material is used室外曝露試驗（如果是塑料邊框） UV (10.10)/the

23、rmal cycling (10.11), 50cycles/humidity freeze (10.12) sequence,if plastic material is used紫外預處理試驗熱循環試驗濕-凍試驗，如果塑料材質被使用 Damp heat (10.13) if an adhesive system is used to mount the module濕-熱試驗，如果組件被安裝時需要依靠粘結力。 Thermal cycling (10.11), 200cycles, if an adhesive system is used to mount the module熱循環試驗，

24、如果膠粘劑的系統被用來裝載組件g) Modification to junction box/electrical termination接線盒或電氣引出端變更For modification such as: Different material不同材料 Different design不同設計 Different potting material不同灌裝材料 Different method of attachment在組件上的安裝方式Repeat: TC 50(10.11), 10 HF (10.12) 熱循環試驗濕-凍試驗 Robustness of terminations (10.

25、14) 引出端強度試驗 Damp heat (10.13) 濕-熱試驗 By-pass diode thermal test (10.18) (if bypass diode is in the box) 旁路二極管熱性能試驗h) Change in cell interconnect materials or technique 電池互聯的材料或方式變更For modifications such as Different interconnect material不同互聯帶材料 Increased thickness of interconnect material (for thickn

26、ess increase greater than40µm.If the new ribbon thickness is below 100 µm thickness no retest is required).增加互聯帶厚度（對于增加厚度大于40 m的。如果新的焊帶厚度低于100 m的沒有需要重測）。 Different bonding technique不同焊接技術 Different number of interconnects不同的互聯數量 Different number of solder bonds per cell不同電池的焊接數量 Different

27、solder material or flux不同的焊接材料或助焊材料Repeat: Temperature cycling,200 cycles (10.11) 熱循環試驗 Damp heat(10.13) for changes in materials濕-熱試驗 Hot spot for changes in bonding technique or solder material(10.9) 熱斑耐久試驗（對于粘接技術或焊錫材料的變化）i) Change in electrical circuit of an identical package 相同組裝的電路變更For modific

28、ation such as: Modification to the interconnection circuitry (for example more cells per bypass diode or re-routing of output leads) 變更互聯電路(如旁路二極管并接的電池串聯數增加，輸出引線的重新走線) Reconfiguration of voltage (i.e. 12V to 24V) 電壓的重新配置(如12v改成24v)Repeat: Hot spot (10.9),only if more cells per by-pass diode熱斑耐久試驗，針對

29、二極管旁路電池片數增加的情況下。 By-pass diode thermal test if the current in each diode increases (10.18)旁路二極管熱性能試驗如果通過二極管的電流會增加 Temperature cycling,200 cycles (10.11) if there are internal conductors behind the cells熱循環試驗（電池片背后通過有內聯條）j) Higher or lower power output (by 10%)in an identical package including size a

30、nd using identical cell process在相同的組裝（包括尺寸）和使用相同的電池工藝的情況下，其功率輸出高于或低于10%以上Repeat: Hot spot (10.9) 熱斑耐久試驗 Bypass diode thermal test (10.18) if greater than 10% higher旁路二極管熱性能實驗（電流增加超過10）k) Qualification of a frameless module after the design has received certification as a framed module有邊框的組件變更為無邊框的組件

31、Repeat the following tests with the laminate mounted using the manufacturers mounting instructions: 重做以下試驗時，層壓板的安裝使用廠家的安裝說明 Damp heat (10.13) (If frame is part of the package seal) 濕-熱試驗 Mechanical load (10.16) 機械載荷試驗 Hail impact (unless superstrate is tempered glass ) (10.17)冰雹試驗l) Change in By-pas

32、s diode旁路二極管變更 Lower current rating or lower temperature rating較低的額定電流或溫度較低的等級 Different number of by-pass diodes per module每個組件二極管的不同數量 Different type or manufacturer不同類型的制造商Repeat: Bypass diode thermal test (10.18) 旁路二極管熱性能實驗Modifications that do not require re-testing不需要重新測試的更改Provided that all s

33、tructural components, materials used and processes (including cell process) remain the same, the following modifications shall not require re-testing:所提供的所有結構組件，所采用的材料和工藝相同，以下的更改不要求重新做試驗： Fewer cells in module減少組件的電池片 Smaller cells in module, as long as each cell has the same number or area of inter

34、connects and equivalent numbers of solder bonds per unit area組件上的電池片減小，只要每個電池片具有相同的數目或面積的互連，相同面積上的焊點數相同。Explanatory Notes:說明：Retest Guidelines is a very important and dynamic document. It is discussed and updated periodically by relevant NCBs, CBTLs, and IEC TC82 WG2.重測導則是一份非常重要有力度的文件，這是由相關NCBs, CBT

35、Ls, and IEC TC82 WG2討論并定期更新的。Before this PDSH, the Retest Guidelines was published on IECEE website under a special entry:在此決定發文之前，重測導則發表于IECEE網站下的一個特別入境：File name 文件名:RetestGuideline_IEC61215_61646def.pdf.pdfDated日期: 2006-04-30Website location網址: By transferring this documents to the form of Decisi

36、on Sheets, PV now only deals with IECEE normal procedures. It will be much easier for all users, especially for new laboratories and some assessors.關于這項決定文件的傳遞，光伏現在只處理IECEE正常程序，這對所有使用者將容易得多，特別是新的實驗室和一些評審員。With the publication of this Decision Sheet,RetestGuideline_IEC61215_61646def.pdf.pdf will be w

37、ithdrawn from the above website.這份決定表發文，重測導則_IEC61215_61646def.pdf.pdf將從上述網站中撤回。2022-1-6 Page 11 of 11Modification/Testprogramme修改/測試方案OutdoorExposure戶外曝光10.8Hot spotendurance熱力耐點10.9UV pre-conditioningIEC61215紫外線前空調10.10Thermal cycling(50 cycles)熱循環10.11Humidityfreeze濕度凍結10.12Thermal cycling(200cyc

38、les)熱循環10.11Damp heat濕熱10.13Robustnessof termina-tions終止強度10.14Mechanical load機械負荷10.16Hail impact冰雹沖擊10.17Bypass diodethermal test旁路二極管熱試驗10.18Change in cell technology or thickness電池片工藝或厚度的改變: 25% if t200µm 17.5%200µmUnless sameChemical surfacetreatment如果不是同一化學表面處理If reduced Thickness如果減

39、少厚度Modification toencapsulation system塑封系統的修改If change inmaterial composition如果在物質組成上改變If nottempered如果不調劑Modification tosuperstrate 前板的變更(e.g. thickness change10%)If change in material如果原材料改變If non-glass:Change in Material or thickness如果非玻璃：材料或厚度的改變If non-glass如果非玻璃If reducedthickness orMaterial change如果減小厚度或改變?cè)牧螩hange in module size組件規格的改變20% in length or w