實驗GRE隧道流量的IPSEC加密

1、由于IPSEC只支持對單播流量的加密，所以我們使用GRE隧道可以將廣播、組播包封裝在一個單播包中，再用IPSEC進行加密。 在進行IPSEC配置前應首先配置好GRE隧道，下面是R1上的GRE隧道配置：R1：interface tunnel0  ip address 192.168.3.1 255.255.255.0  tunnel source s1/1  tunnel destination 192.1.1.20  exitinterface s1/1   ip address 192.1.1.40 255.255.255.0

2、60; ip access-group perimeter in  exitinterface lo0  ip address 192.168.1.1 255.255.255.0  exitip route !在這里我將總公司內部的骨干網絡設為Area0,隧道部分和分公司內部網絡設為Area1router ospf 1  network 192.168.1.0 .255 area 0  network 192.168.3.0 0.0.0.255 area 1  exitip access-list extended perimeter

3、  permit udp host 192.1.1.20 host 192.1.1.40 eq 500  permit esp host 193.1.1.20 host 192.1.1.40   permit gre host 193.1.1.20 host 192.1.1.40  deny ip any any  exit R2：interface tunnel0  ip address 192.168.3.2 255.255.255.0  tunnel source s1/0  tunnel dest

4、ination 192.1.1.40  exitinterface s1/0   ip address 192.1.1.20 255.255.255.0  ip access-group perimeter in  exitinterface lo0  ip address 192.168.2.1 255.255.255.0  exitip route router ospf 1  network 192.168.2.0 .255 area 1  network 192.168.3.0 0.0.0.255 area

5、 1  exitip access-list extended perimeter  permit udp host 192.1.1.40 host 192.1.1.20 eq 500  permit esp host 192.1.1.40 host 192.1.1.20   permit gre host 192.1.1.40 host 192.1.1.20  deny ip any any  exit   GRE隧道建立好后，就可以進行IPSEC配置了：R1上的配置：crypto isakmp enablecr

6、ypto isakmp identity addresscrypto isakmp policy 10  encryption aes  authentication pre-share  group 2  hash sha  exitcrypto isakmp key cisco123 address 192.1.1.20 no-xauth!IPSEC只對進入GRE隧道的流量進行加密ip access-list extended ToR2  permit gre host 192.1.1.40 host 192.1.1.20

7、0; exit!這里的GRE隧道是點對點模式的，所以傳輸集應使用傳輸模式crypto ipsec transform-set trans esp-aes esp-sha-hmac  mode transport  exitcrypto map mymap 10 ipsec-isakmp   match address ToR2  set transform-set trans  set peer 192.1.1.20  exitinterface s1/1  crypto map mymap  exit!最后別忘記

8、刪除測試隧道時建立的流量： R2上的配置： 測試實驗結果：r1#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area        N1 - OSPF NSSA external type 1, N2 - OSPF NSSA

9、external type 2       E1 - OSPF external type 1, E2 - OSPF external type 2       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2       ia - IS-IS inter area, * - candidate default, U - per

10、-user static route       o - ODR, P - periodic downloaded static routeGateway of last resort is 192.1.1.20 to network .0C    192.1.1.0/24 is directly connected, Serial1/1C    192.168.1.0/24 is directly connected, Loopback0   

11、  192.168.2.0/32 is subnetted, 1 subnetsO       192.168.2.1 110/11112 via 192.168.3.2, 00:00:17, Tunnel0C    192.168.3.0/24 is directly connected, Tunnel0S*    R1上ping PC2:Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 36/56/84 msPC1上ping PC2:r1#ping 192.168.2.1 source lo0Type escape sequence to abort.Sending