SHDSL使用手冊(cè)

1、Table 1-2 SHDSL IP DSLAM LED Description<LED ID> Color DescriptionPOWER Green Lit when power onMAINT Yellow Lit when maintance commands were issuedALARM Red Lit when MJ/MN events happenFAULT Red Lit when system error is detectedUP-LNK Green Lit when Uplink Ethernet interface was connectedUP-AC

2、T Green Blink when information is transmitted through uplinkEthernet interfaceUP-100 Green Lit when Uplink is 100Mbps.ID-2, ID-1& ID-0 Yellow ID0, ID1,ID2 : off off offEmbedded Web Interface(EmWeb)The embedded Web Interface (EmWeb), comprised of HTML files, is moreuser friendly than CLI for your

3、 configuring SHDSL IP DSLAM. The HTML filesembedded in SHDSL IP DSLAM are dynamically linked to the systemsfunctional command sets. You can access the EmWeb from any Web Browser.Following the following procedure to connect the embedded Webmanagement interface:1. Establish a connection to the interne

4、tUM-2400S-1-B 2003 232. Open the Web browser4. Log in User account: admin and Password: adminTo access any menu item on EmWeb, simply click on the item you want. Thecorresponding work screen will then appear on the right side frame. By pressingthe Apply button will allow you to achieve your configur

5、ation, whereas pressingCancel button will clear all your changes without applying them. In some menus,there will be Modify item will allow you to modify the existing configuration.Command Line Interface (CLI)The Command Line Interface is the most primary character basedconfiguration interface. Some

6、of configurations not provided in EmWeb can beconfigured through CLI. You can access CLI from the terminal emulationsoftware.The procedure of connecting to the CLI is as follows:1. Start up the terminal emulation software on the management station.2. If necessary, reconfigure the terminal-emulation

7、software to match the switchconsole port settings.Bits per second 9600Data bits 8Parity NoneStop bits 1Flow control None5. Log in User account: admin and Password: adminLog In with Embedded Web InterfaceThis section describes how to log into Embedded Web Interface.1. Connect your computer with the u

8、plink port of SHDSL IP DSLAM.3. The log in screen appears as follows: 4. Enter your user name. If it is an initial installation, enter admin for user name.5. Enter your password. If it is an initial installation, enter admin for password.Embedded Web Interface MenuThis section describes the overview

9、 of the embedded Web interface menu,EmWeb. After your successfully logging into the EmWeb, the screen willappears as follows:Default SettingDisplay the information of default (factory) setting of your SHDSL IPDSLAM.System InformationDisplay the system time, system up time, system up period of yourSH

10、DSL IP DSLAM. It also provides you with the information of software version,hardware version and serial number.Save to FlashAllow you to save your configuration in Flash.Current EventAllow you to view the alarm and event stSTUs of your SHDSL IP DSLAM.Default (Factory) Configuration Settings DefaultS

11、ettingThis section describes how to get the information of the default setting ofyour SHDSL IP DSLAM.1. Click on “Default Setting” from the SHDSL IP DSLAM Main Menu.The Default Setting screen appears as follows:Displaying your SHDSL IP DSLAMs SystemInformation System InformationThis section describe

12、s how to get the information of your SHDSL IP DSLAM.1. Click on “System Information” from the SHDSL IP DSLAM Main Menu.The System Information screen appears as follows:Save your Configuration to Flash Save to FlashThis section describes how to save the configuration you have configured toflash. This

13、 function will be needed whenever you want to restart your SHDSL IPDSLAM with the updated configuration.1. Click on “Save to Flash” from the SHDSL IP DSLAM Main Menu.The Save to Flash screen appears as follows:2. Submit the Save button.Displaying Current Event Current Event This section describes ho

14、w to view the current alarm and event stSTUs.1. Click on “Current Event” from the SHDSL IP DSLAM Main Menu.The Current Event screen appears as follows:2. Click on next page item in order to view more events. The displayed data willbe 20s items per page and it can display totally up to 960s items.3.

15、Click on DELETE ALL button in order to delete all events.Configuring SHDSL IP DSLAMThis section describes how to configure your SHDSL IP DSLAM by selectingSystem from EmWeb Menu. This section will cover all the function from SystemMenu. It includes:Configuring Port Filtering Set Port FilterAllow you

16、 to configure the port filtering function.1. Click on “Set Port Filter” from the System Menu.The Set Port Filter screen appears as follows:2. Click on Enabled button to allow each SHDSL port to communicate backand forth with the uplink Ethernet port only.By selecting Disabled button you allow all SH

17、DSL ports to communicate34 2003 UM-2400S-1-Bwith each other and also with the uplink Ethernet port.3. Press Apply button in order to submit your configuration.Note: Make sure to save all the configurations in flash by selecting Save toFlash from main menu when you want to restart your SHDSL IP DSLAM

18、.Configuring IP and Location System IP / LocationAllow you to configure the system IP address and location.1. Click on “System IP / Location” from the System Menu.The System IP / Location screen appears with the default setting and canbe configured as follows:2. Configure the IP address you want to

19、set, say 3. Configure the subnet mask with reference to IP address, say 4. Configure the gateway with reference to IP address, say 5. Configure the system name you want to set, say IP DSLAM6. Configure the site of location you want to set.7. Configure the contact information for servicing SHDSL IP D

20、SLAM.36 2003 UM-2400S-1-B8. Click on the Apply button to submit your changes, or click on the Cancelbutton if you want to clear all the values you have configured.Configuring Date and Time System Date and TimeAllow you to configure the date and time of the system.1. Click on “System Date and Time” f

21、rom the System Menu.The System Date and Time screen appears with the default setting andcan be configured as follows:2. Configure the year you want to set, say 20013. Configure the month you want to set, say 014. Configure the day you want to set, say 015. Configure the hour you want to set, say 206

22、. Configure the minute you want to set, say 017. Configure the second you want to set, say 018. Click on the Apply button to submit your changes, or click on the Cancelbutton if you want to clear all the values you have configured.38 2003 UM-2400S-1-BChanging your Password Changing PasswordAllow you

23、 to change your password.1. Click on “Changing Password” from the System Menu.The Changing Password screen appears with your user name and yourpassword can be changed as follows:2. Enter your old password.3. Enter your new password that you want to change.4. Enter your new password again to confirm.

24、5. Click on the Apply button to submit your changes, or click on the Cancelbutton if you want to clear all the values you have configured.DSL Line ConfigurationThis section covers how to create, display, modify, or delete the line profileand alarm profile by selecting DSL Line Configuration from EmW

25、eb Menu.This section will cover all the function from DSL Line Configuration Menu.Creating a SHDSL Line Profile Create Line ProfileThis section describes how to create a SHDSL line profile.1. Click on “Create Line Profile” of G.SHDSL from the DSL Profileconfiguration Menu.The Create Line Profile scr

26、een appears as follows:2. Configure the name of line profile, say service 1552K.3. Configure the line profile, for example,Configure the WireInterface, Minimum Line Rate, Maximum Line Rate, PSD,TransmissionMode, RemoteEnabled, PowerFeeding,CurrCondTargetMarginDown, WorstCaseTargetMarginDown,CurrCond

27、TargetMarginUp, WorstCaseTargetMarginUp,UsedTargetMargins, ReferenceClock, and LineProbeEnable as Two Wire,1552 kbps, 1552 kbps, Symmetric, Region1, Disabled, NoPower, 0s dB, 0sdB, 0s dB, 0s dB, CurrCondDown, LocalClk and Disabled.4. Click on the Apply button to submit your changes, or click on the

28、Cancelbutton if you want to clear all the values you have configured.Note: Line profile can be created maximum up to 10s profiles.40 2003 UM-2400S-1-BCreating a SHDSL Alarm Profile Create Alarm ProfileThis section describes how to create an SHDSL alarm profile.1. Click on “Create Alarm Profile” of G

29、.SHDSL from the DSL Profileconfiguration Menu.The Create Alarm Profile screen appears as follows:2. Configure the name of alarm profile.3. Configure the alarm profile. For example,Configure the ThreshLoopAttenuation, ThreshSNRMargin, ThreshES,ThreshSES, ThreshCRCanomalies, and ThreshLOSWS as 0s db,

30、0s db, 0,0s ec, 0s ec,4. Click on the Apply button to submit your changes, or click on the Cancelbutton if you want to clear all the values you have configured.Note: The alarm profile can be created maximum up to 10s profiles.5. Click on Modify button to modify the specified profile.6. Click on Dele

31、te button to delete the specified profile.Port ConfigurationThis section covers how to configure a port and subscriber information byselecting Port Configuration from EmWeb Menu. This chapter will cover allthe function from Port Configuration Menu.DSL Port ConfigurationDSL Port ConfigurationAllow yo

32、u to display, modify and delete the stSTUs of the port. It alsoprovides the configuration of enabling or disabling a port and attaching thespecific line profile and alarm profile to a port. The procedures are as follows:1. Click on “DSL Port Configuration” from the Port configuration Menu.For first

33、time configuration, the DSL Port Configuration screen appears withthe default setting as follows:2. Click on the Port No to select the port you want to configure or view.3. The screen will apears as follows:4.Configure the adminstration status as “Up” or “Down”. Here in example , “Up”is configured.5

34、. Attach the line profile, says “DEFAULT”6. Attach the alarm profile, says “DEFAULT”7. Click on the Apply button to submit your changes, or click on the Cancelbutton if you want to clear all the values you have configured.UM-2400S-1-B 2003 45PVC ConfigurationPVC ConfigurationAllow you to configure P

35、VC (Permanent Virtual Connection) and VID (VLANID) on a port and setting the priority. It also provides the modification and deletefunction. The procedures are as follows:1. Click on “PVC Configuration” from the Port configuration Menu.For the first time configuration, the PVC Configuration screen a

36、ppears withthe default setting as follows:2. Click on the Port No you want to configure or view.3. Click on the Apply button to sumit your choice.4. Click on Delete button to delete the settings.5. Click on Modify button to configure the specific port, says port1. The screenwill apears as follows:6.

37、 Configure the VPI, says 87. Configure the VCI, says 818. Configure the administration stSTUs of PVC “Up” or “Down”, says “Up.9. Configure the VID of the port.10. Configure the priority of PVC, says 7. The priority of 0s to 7 is from thelowest to the highest.11. Click on the Apply button to submit y

38、our changes, or click on the Cancelbutton if you want to clear all the values you have configured.List of Subscriber List of SubscriberAllow you to view the existing information of subscribers and modify them. Theprocedures are as follows:1. Click on “List of Subscriber” from the Port configuration

39、Menu.For the first time configuration, the List of Subscriber screen appears withthe default setting as follows:2. Click on the Port No you want to configure or view.3. Click on the Apply button to sumit your choice.4. Click on Delete button to delete the settings.5. Click on Modify button to config

40、ure the specific port, says port1. The screenwill apears as follows:6. Configure the subscriber name as you want, says Pantagon.7. Configure the telephone number of subscriber, says 423612588. Write Note for your reference if you need.9. Click on the Apply button to submit your changes, or click on

41、the Cancelbutton if you want to clear all the values you have configured.Management ConfigurationThis section covers how to configure SNMP access parameters andmanagement IP by selecting Management from EmWeb Menu. This sectionwill cover all the function from Management Menu. It includes:Configuring

42、 SNMP Access Parameters and Trap IPs SNMPAllow you to configure the SNMP access parameters and trap IPs. Theprocedures are as follows:1. Click on “SNMP” from the Management Menu.For the first time configuration, the SNMP screen appears with the defaultsetting of the community string” public” as foll

43、ows:2. Configure the VID (VLAN ID) of the system3. Configure the trap IP Addresss as you want. The trap IP can be createdmaximum up to 5.4. Click on the Apply button to submit your changes, or click on the Cancelbutton if you want to clear all the values you have configured.Configuring Management IP

44、 Management IPAllow you to configure the management IPs so that only with thoseconfigured management IPs can access to your SHDSL IP DSLAM remotely.The procedures are as follows:1. Click on “Management IP” from the Management Menu.The Management IP screen appears as follows:2. Configure the manageme

45、nt group as you want. The management IP groupcan be created maximum up to 5 groups.3. Click on the Update button to submit your changes, or click on the Cancelbutton if you want to clear all the values you have configured.SHDSL MaintenanceAllow you to configure the maintenance operations on SHDSL units. Theprocedures are as follows:1. Click on “SHDSL Maintenance” from the Main Menu.The SHDSL Maintenance screen appears as follows:4. if you want to config the setting of a specifie