ECG原理與技術

1、 心臟是人體血液循環的動力裝置，心臟自律不斷地心臟是人體血液循環的動力裝置，心臟自律不斷地進行有節奏的收縮和舒張活動，使血液在閉鎖的循環系進行有節奏的收縮和舒張活動，使血液在閉鎖的循環系統中不停的流動，使生命得以維持統中不停的流動，使生命得以維持。 心肌細胞的除極、復極過程和動作電位心肌細心肌細胞的除極、復極過程和動作電位心肌細胞在興奮時所發生的電位變化稱為動作電位，即心胞在興奮時所發生的電位變化稱為動作電位，即心肌細胞的除極和復極過程（如圖）。肌細胞的除極和復極過程（如圖）。舊式的心電圖機多數采用熱筆在熱敏紙上記錄波形,存在著打印效率低、噪聲大、波形失真等缺點;而熱敏打印機的熱敏頭是由一排體

2、積很小( 8個/mm)的加熱單元組成的,每個加熱單元加熱時與之相接觸的熱敏紙的對應位置將會變黑,通過控制各個加熱器件的加熱與否即可控制每一行的打印內容,再由步進電機控制走紙換行,從而在熱敏紙上繪制出各種圖形。由于熱敏打印機具備體積小、重量輕、可靠性高、打印字符清晰、噪聲小、走紙均勻等特點,因此成為新型心電圖機的首選金屬反應金屬反應電極電位電極電位(V)(V)Zn Zn2+ +2e 0.763Ni Ni2+ +2e0.250Cu Cu2+2e0.337Ag Ag + e0.799AgCl+e0.22312SLTM金標準分析程序 屏幕3通道顯示，12導可同步打印 自動，手動，心率失常模式 內置歐洲

3、標準的HEART分析軟件QTD的精確分析 報告準確，格式多樣 交直流兩用 可升級運動測試系統 抗漂移系統(ADS)及自動基線調整 主要規格： 導聯：標準12導聯 增益轉換：5，10，20，40mV，手動或自動 記錄紙：GE marquette-hellige式對比度熱敏紙300*210mm電源：交流電源：85-264V,直流電源：內置電池 外形尺寸：370*320*95（mm） 重量：5.6Kg（含電池組）Device cannot be switched on even though power plug is plugged in- green power lamp LED is off

4、and device cannot be switched on:- Power cable defective or not plugged in correctly?- Primary fuses in the mains input module defective?- Connector from the mains input module to the mains switching power supplyplugged in correctly, or cable defective?- Connector from the mains switching power supp

5、ly to connector POSUP/ on thePCB Control plugged in correctly, or cable defective?- Keypad via connector KEYB/ on PCB Control plugged in correctly?- 26,5V on the connector POSUP? if no: - mains switching power supply defective if yes: - PCB Control defective- or keypad defective- green power lamp LE

6、D is on, but device still cannot be switched on: - PCB Control defective- or keypad defectiveDevice cannot be switched on when being battery-operated only- Is the battery depleted?- Plug in power plug, green power lamp LED should glow and the device can beactivated, if not: - refer to Device cannot

7、be switched on even though powerplug is plugged in”.- By connecting the power plug, rapid charging is activated, LED1 on the PCBBattery Charge is activated if not: - PCB Battery Charge is defective- With power plug plugged in, let unit charge for 10 minutes, then disconnectpower plug. Can the device

8、 be switched on and can a recording be started? if yes: - Function OK., continue loading with plugged mains plug if not: - Battery disconnected or cable defective?- Battery defective (no capacity)?- PCB Battery Charge defective ( Si1?)?No display on the screen- Does the yellow Stop LED on the keypad

9、 glow after the device is switched on? if not: - refer to Device cannot be switched on .” if yes: - continue- Does a beep sound approx. 10s after switching on the MAC1200 occur (indicatesthe successful power up self-test)? if not: - Self test error, PCB Control defective if yes: - continue- Contrast

10、 badly adjusted?- Can the background illumination be activated by pressing a key?- Can the display test in Section 3.3 be applied successfully? if not: - graphics display module defective- or PCB Control defectiveMAC 1200 fails to give printout, no paper transportPerform the following test in the 6-

11、lead operating mode:- Paper available? Paper correctly inserted? Paper transport problems (jam)?- Paper feed flap correctly engaged on both sides?- After pressing the start key, the green start Led must glow if not : - keypad defective? Apply keypad test in Section 3.4 if yes: - continue- Paper feed

12、 flap correctly engaged on both sides?- Mark reader defective or not plugged in?- All connections for printhead and Motor are plugged in?- Motor blocked ? (check roller, transmission)- Operating only on battery which is strongly depleted? if yes: - plug in power plug if not: - PCB Control defectiveP

13、aper transport functions, no printout- Paper feed flap correctly engaged on both sides?- All connectors for printhead plugged in?- Operation with strongly depleted battery? if yes: - plug in power plug if no: - PCB Control defective- or printhead defectiveMAC 1200 prints, but only baselines are printed out- Electrodes applied correctly?- Electrode cables pl