反時限過負荷保護電流時間特性對照表(精)

1、160 反時限過負荷保護電流時間特性對照表曲線系數K=10-1200動作時間（秒）10256075100125250300500750100012001.147.62119.05285.71357.14476.19595.241190.41428.52380.93571.44761.95714.21.222.7356.82136.36170.45227.27284.09568.18681.821136.31704.52272.72727.21.314.4936.2386.96108.70144.93181.16362.32434.78724.641086.91449.21739.11.410.

2、4226.0462.5078.13104.17130.21260.42312.50520.83781.251041.61250.01.580020.0048.0060.0080.00100.00200.00240.00400.00600.00800.00960.001.7548512.1229.0936.3648.4860.61121.21145.45242.42363.64484.85581.82233383320.0025.0033.3341.6783.33100.00166.67250.00333.33400.002.2524661514.7718.4624.6230.7761.5473

3、.85123.08184.62246.15295.382.519047611.4314.2919.0523.8147.6257.1495.24142.86190.48228.572.7515238191411.4315.2419.0538.1045.7176.19114.29152.38182.86312531375093812.5015.6331.2537.5062.5093.75125.00150.003.50892225336678.8911.1122.2226.6744.4466.6788.89106.6740671674005006.6783316.6720.0033.3350.00

4、66.6780.004.50521303123905.1964912.9915.5825.9738.9651.9562.3450421042503134.1752110.4212.5020.8331.2541.6750.005.50340852052563.424278.5510.2617.0925.6434.1941.0360290711712142.863577.148.5714.2921.4328.5734.296.50240611451822.423036.067.2712.1218.1824.2429.0970210521251562.082605.216.2510.4215.632

5、0.8325.007.20200491181481.972464.925.909.8314.7519.6723.607.50180451091361.812264.525.439.0513.5718.1021.7280160400951191.591983.974.767.9411.9015.8719.05用法舉例：按上表，當用戶選擇曲線速率K為60時，如過負荷電流是三倍額定電流，則對應的反時限動作時間是7.50秒。反時限曲線時值示意圖10000500010005001005010時間設定倍數10501最高過載倍數2345678910額定電流倍數四、外形尺寸160*80型儀表外型尺寸圖啟動A啟

6、動B五、安裝及接線標準智能電動機保護器160*80；采用面板卡式安裝。開孔尺寸：152*76。將電動機三相電流互感器的次級分別接至電動機保護器的相應輸入端子。（詳見產品接線圖）將高壓電動機三相電壓互感器的次級分別接至電動機保護器的相應輸入端子（低壓電機可直接接入，詳見產品接線圖）四組輸出繼電器，分別用于報警、前級跳閘和啟動/停止A、啟動/亭止B,不用懸空即可。無源觸點“啟動A”“啟動B”“停止/復位”用于電動機的正常啟動和停止；“緊急停止”是現場使用的非正常停止按鈕；“A反饋”“B反饋”為接觸器動作信號，通常與常開輔助接點相連;“斷路器狀態”是前級開關送電信號，如不使用前級跳閘功能，此接點短路即可；“遠程控制”是現場控制權轉移開關，接點閉合時，可通過RS485遠程啟動/停止電機保護器。保護控制器電源最好不與電機使用同一條線，否則將影響“晃電”功能的使用；若必須與電機使用同一電源時，請選擇具有電源保持功能的保護控制器?！白兯洼敵觥薄巴ㄓ崱焙汀奥╇奀T”端子，使用時連接，不使用時懸空。HD5200電機保護器接線端子定義12345678910111213141516171819202122+laIbIcUaUbUcU0IO2324252627282930313233343536啟啟停緊AB斷遠COM動動止急反反路程AB復停饋饋器