SPC-P175-36V 8Ah 規格書-H版-訂單 YP-SD-C114 客供外殼

1、.：.；江西中投新能源JIANG XIZ.T NEW ENERGY CO.,LIMITED規格確認書Specification for ApprovalSeries產品系列Lithium PolymerModel and Capacity型號及容量36V 8AhCustomer Name or code客戶稱號或代碼YP-SD-C114File No.文件編號ZT -SPC-P175File Version版本號A0Issue Date發行日期2021-08-04同意Approved審核Checkup制造PreparedCustomer Approval客戶確認Signature簽名Date日

2、期Company Name:公司稱號：Company Stamp:公司印章：江西中投新能源JIANG XIZ.T NEW ENERGY CO.,LIMITEDAEMDMENT RECORDS(規格變卦記錄)版本號 Version Number變卦內容描畫Emendatory content description更改頁 Emendatory page發行日期 Issued Date制造Prepared審核Checkup同意Approved制造商保管在沒有預先通知的情況下改動和修正設計及規格闡明書的權益 1 of 10 Manufacturer reserve the right to alte

3、r or amend the design, model and specification without prior notice Contents目錄1 適用范圍Scope32 體系System 33 常規技術參數General Specifications34 產品性能測試Product performance test 45 產品儲存及運輸Product Storage and Transportation66 電池操作指引Battery Handling Guideline 67 本卷須知Remark8附錄Appendix9制造商保管在沒有預先通知的情況下改動和修正設計及規格闡明書

4、的權益 2 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice 1.適用范圍Scope本產品規格書適用于江西中投新能源向客戶提供的可充電鋰聚合物電池產品 36V 8Ah。This specification is applied to rechargeable Lithium Polymer Cell 36V 8Ah produced by Jiangxi Z.T New Energy CO., LTD.2. 體系Syste

5、m可充電聚合物鋰離子電池Rechargeable Lithium Ion Polymer Battery3. 常規技術參數General SpecificationsNO.工程Item規格參數Specification1型號 Model36V8Ah ( 2P10S)2額定容量 Rated Capacity ( 5A)最小值:Min.: 8Ah HYPERLINK mailto:2Acharge (2Acharge and 5A discharge)特征值:Typical:8.5Ah HYPERLINK mailto:2Acharge (2Acharge and 5A discharge)3內阻

6、 internal Impedance 200mohm4標稱電壓Nominal Voltage36V5充電截止電壓Charging Voltage420.05V6充電方法Charging Method恒流恒壓充電 CC&CV規范充電制度Standard Charging Process在 25C5 C 下，以 2A 恒流充電至 42V,然后恒壓充電到充電電流減小到 0.02C，即充溢電。2A (CC) charge to 42V, when 42V (CV) is reached, charge rate will reduce to 0.02C(A) for full charge7放電方法

7、Discharging Method恒流放電 constant current discharge8規范放電制度Standard Discharge method在 20C5 C 下以 5A 恒流放電至 30.0V。Cells should be discharged at a constant current of 5Ato 30.0 volts at 20C 5 C9規范放電時間Standard discharge time120min10最大繼續放電電流Max. Continuous DischargeCurrent8A11放電截止電壓Discharge Cut-Off Voltage3

8、0.0V制造商保管在沒有預先通知的情況下改動和修正設計及規格闡明書的權益 3 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice 12電池外殼資料The crust data客供外殼，最大外形尺寸為435mm 81mm130mm詳細見附圖The curst is supplied by the client，the maximum dimensions is435mm 81mm130mm， refer to the atta

9、ched drawing13電池分量(最大值)Battery Weight(MAX)3.5Kg14電池循環壽命 (規范充放電)battery Cycle Lifestandard charge& discharge 500 次 注:剩余容量60%remark: the residualcapacity is more than 60% of the first cycle discharge capacity15操作溫度 Operating Temperature放電Discharge-20C to 55C充電Charge0C to 45C儲存Storage10C to 30C16儲存溫度 S

10、torage temperature1 個月內Within 1 month- 5C +45C3 個月內Within 3 month- 5C +35C6 個月內Within 6 month0C +35C4. 產品性能測試Products performance testNO.ItemsTestcondition and methodCriterion1荷電性能Self-dischargePerformance規范充電后在 205條件下儲存 30 天，然后用 5A 的電流放電至放電截止電壓 Standard Charged according to 5. 3.1，lay for 30 days i

11、n the aminenttemperature of 20 C5 C,then discharge to the discharge end voltage 30.0 V at the current of 5A放電容量: 85%初始容量The discharge Capacity: should not less than 85% of Initial Capacity2高溫放電性能High TemperatureDischarge規范充電后，把電池放入 555高溫箱中擱置 2 小時，然后然后用 0.2C 的電流放電至放電截止電壓standard Charged according to

12、5. 3.1，lay for 2 hoursin the ambient temperature of 55 C5 C, then discharge to the discharge end voltage 30.0V at the current of 0.2C放電容量 90%常溫放電容量The Discharge capacity should not less than 90% of the capacity that discharge at normal temperature3低溫放電性能Low TemperatureDischarge規范充電后，把電池放入-205低溫箱擱置 1

13、6-24h 后用 0.2C 的電流放電至放電截止電壓standard Charged according to 5. 3.1，lay for 24hours in the ambient temperature of -20 C5C ,then discharge to the discharge end voltage30.0V at the current of 0.2C放電容量 70%常溫放電容量The Discharge capacity should not less than 70% of the capacity that discharge at normal temperat

14、ure制造商保管在沒有預先通知的情況下改動和修正設計及規格闡明書的權益 4 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice 4過充電測試Over charge test規范充電后，恒流恒壓源設定為 50V 以 1C 的電流繼續充電 8hBattery charged at 1.0C current with a voltage limit of50.0V.charging is continued for 8 hours

15、.不爆炸、不起火no explosion, no fire5過放測試Over-discharge0.5C 放電至 30.0V 后再以 0.2C 的電流放電至 0VBattery discharged continuously at the constant current of 0.5C to 30.0V,then discharge the battery with a current of 0.2Cto 0V不爆炸、不起火No Explosion, No Fire6熱沖擊測試Heating Test將滿電電池置于高溫箱中、溫度以52/min 升到 1302并保溫 30 分鐘The temp

16、erature of the oven is to be raised at a rate of 52/min. to a temperature of 1302, andremains for 30 minutes at this temperature.不爆炸、不起火No Explosion, No Fire7振動測試Vibration test電池在振幅為 0.8 mm 1.6mm的簡諧振動，振動頻率為：1055 Hz,掃頻速率為:1 Hz/min, X、Y、Z 三個方向各振動一次，振動時間為 30min.Let the battery subjected simple harmonic

17、 motion with an amplitude of 0.8 mm 1.6mm total maximumexcursion.The frequency is to be varied at the rate of1 hertz per minute between 10 and 55 hertz, The battery is to be tested for 30 min in each mutually perpendicular directions.不爆炸、不起火No Explosion, No Fire8自在跌落測試 Free falling(drop) Test規范充電后，擱

18、置 2 小時,從 1m 高處自在跌落到 30mm厚的木板上,各方向一次。Fully charge，lay for 2 hours , drop the battery from aheight of 1m to a wooden board with the thickness of30mm. Each side for one time.不爆炸、不起火(V0.20V/SetR5%/Set)No Explosion, No Fire9外部短路測試ExternalShort-circuitingtest規范充電后，運用總內阻不大于 100m 的導 線 短路 正負極 ， 當 電池溫度下 降 到 比

19、峰值 低 約 10 時， 終了 試 驗 。Fully charge，Short circuit by connecting the positive and negative terminals with a circuit load having a maximum resistance load of 100m ,un t il i t st e m p e r a t u r e h a s f a ll e n b y 10 f r o m t he p ea k p o i n t , t h e t e s t i s o v e r .不爆炸, 不起火No explosion,

20、no fire10溫度循環測試 Temperature Cycling Test703條件下擱置 4 小時；在 203條件下擱置 2 小時；在-403條件下擱置 4 小時；在 203條件下擱 置 2 小時；按以上的步驟循環 10 次，并且每次溫度變 換時間不得超越 30min 。70 3C maintaining for 4 hours.203C maintaining for 2 hours.-40 3C maintaining this temperature for4 hours.203C for 2 hours. Repeating the sequence for a further

21、 9 cycles. And the temperature changeshould be finished within 30 min不著火、不爆炸；不漏 氣、不漏液No Explosion, No Fire and Not vent or leak11恒 定 濕 熱 測 試Humidityand heat test將規范充電后的電芯放入溫度為402，相對濕度為90%95%的恒溫恒濕箱中48hA charged battery is placed in a box for 48hours where the temperature is 40C2Cand the relative humi

22、dity is 90%95%無冒煙、爆炸 No smoke or explosion12重物沖擊測試Impact test電池按 5.3.1 充電后，把電池放在一個平面上，將直徑為 15.8mm 的鋼棒放到電池的中心，用分量為 9.1kg 的不爆炸, 不起火No explosion, no fire制造商保管在沒有預先通知的情況下改動和修正設計及規格闡明書的權益 5 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice 重物從

23、 610mm 的高度跌落到電池上.After full charged according tosection5.3.1,place the battery on a flat surface. A 15.8mm diameter bar is to be placed across the center of the sample. A 9.1 kgweight is to be dropped from a height of 61025 mm onto the sample.13擠壓測試Crush Test在兩個平面間對電池進展擠壓，壓力經過直徑為 32mm的活塞提供，壓強為 17.2

24、MPa，壓力為 13 kN 即可停止。Crush the battery between two flat surfaces ,The force for the crushing is to be applied by a hydraulic ram with a 32 mm diameter piston. The crushing is to be continued until a pressure reading 17.2 MPa is reached on the hydraulic ram, applied force of 13 kN.不爆炸, 不起火No explosion,

25、 no fire5.產品儲存及運輸Product Storage and Transportation5.1 產品儲存ProductStorage如電池儲存 3 個月以上，電池須置于溫度為 205、濕度為 6520%RH 的環境中，電池的儲存電壓需堅持在 36V40V，請每隔 3 個月電池一次，詳細方法如下:規范充放電后，擱置 5 分鐘，2A 充電至40VIf the cell is to be stored for 3 months or longer , the environment should be as follows: Temperature: 205Humidity: 6520

26、%RHVoltage during storage needs to me maintained between 36V40V .Please charge & discharge the battery once every 3 months according to the following method: Standard charge/discharge, lay for 5 min, then charge at 2A to 40V.5.2 產品運輸Product Transportation電池在運輸中為半電形狀，應防止猛烈震動、擠壓、日曬及浸濕。During transport

27、ationthe battery is approximately at a state of 50% charged, the battery should avoid from acute vibration, crushed, solarization, soaked.6.電池操作指示及本卷須知Handling Precautions and Guideline聲明一： 客戶假設需求將電池用于超出文件規定以外的設備，或在文件規定以外的運用條件下運用電池，應事先聯絡中投新能源，由于需求進展特定的實驗測試以核實電池在該運用條件下的性能及平安性。Note(1):If the battery i

28、s used to other equipments , or used condition is not accord to the condition in this制造商保管在沒有預先通知的情況下改動和修正設計及規格闡明書的權益 6 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice Specification they should contact With Z.T New Energy in advance, Ad

29、ditional experimentation may be required to verify the performance and safety under the conditions.聲明二：對于在超出文件規定以外的條件下運用電池而呵斥的任何不測事故中投新能源概不擔任Note(2):Z.T New Energy will take no responsibility for any accident when the battery is used under other conditions beyond those described in this Document.聲明三

30、：如有必要，中投新能源會以書面方式告之客戶有關正確操作運用電池的改良措施。Z.T New Energy will inform the customer of improvements regarding proper use and handing of the battery in a written form, if it is necessary.6.1. 充電 Charging電池必需在 040的環境溫度范圍內進展充電，充電電流不得超越本規范書中規定的最大充電 電流。充電電壓不得超越本規范書中規定的額定電壓,42V 為充電電壓最高極限，充電器的設計應滿 足此條件；制止反向充電， 用我

31、公司配套的充電器或引薦的充電方法進展充電，充電時間不得超越7hThe battery should be charged within 040 specified in this Specification. The battery should be charged at a current less than the maximum charge current specified in this Specification. Charging Voltage should be less than the specified in this Specification. The Max

32、Charging Voltage is 42V, and the charger should be designed to meet with this requirement. Prohibiting toreverse charge，Charge the battery with the charger or charge method offer by our company, thecharge time not more than 7h6.2放電 Discharging電池必需在-2060的環境溫度范圍內進展放電，放電電流不得超越本規范書規定的最大放電電 流，留意在電池長期未運用期

33、間能夠會因其它自放電特性而處于某種放電形狀。為防止電池過放電， 應定期充電，堅持其電壓高于 30V。The battery should be discharged within -2060 specified in this Specification, The batteryshould be discharged at a current less than the maximum discharge current specified in this Specification. Notice that the battery would be at force-discharged

34、state by its self-discharge characteristics in case the battery is not used for long time. In order to prevent over-discharging, the battery shall be charged periodically to maintain above 30V.6.3.其它事項 Others6.3.1.防止電池內短路Prevent internal short circuit6.3.2.嚴禁裝配電池 Prohibit disassembly6.3.3. 在任何情況下，不得將電池投入火中，否那么會引起電池熄滅。Never dispose the battery in fire. It may cause the battery firing.6.3.4 不得將電池浸泡于液體中，如淡水、海水、飲料