pcf2測量報告全尺寸.part1measured

1、CS11_Fully measured ReportProject Name Part Number CAD Number Product Name:CS11:_008: BRACKET ISOFIX OB LHr:VCC Material standards : VDA 239-CR240LA Actual Material : CR240LAThickness: 2.0mmCoating thickness : UC Detection time :2016/12/11CHECK RESULT 檢查結果CHECK DATE檢測日期OK.RATIOPart codeP1P2P3TOTAL全尺

2、寸OK Ratio100%100%100%OK Pos787878Total Pos787878SURF.型面OK Ratio100%100%100%OK Pos404040Total Pos404040TRIM修邊OK Ratio100%100%100%OK Pos343434Total Pos343434HOLE孔位孔徑OK Ratio100%100%100%OK Pos444Total Pos444RPS InformationStep1:SurfaceCheckingRationalDMIS(TM) External-Array Software, Inc第 1 頁西安力德測量設備Ra

3、tionalDMIS(TM) External-Array Software, Inc第 2 頁西安力德測量設備RationalDMIS(TM) External-Array Software, Inc第 3 頁西安力德測量設備Step2:TrimCheckingRationalDMIS(TM) External-Array Software, Inc第 4 頁西安力德測量設備RationalDMIS(TM) External-Array Software, Inc第 5 頁西安力德測量設備Step3:HolesitionRationalDMIS(TM) External-Array Soft

4、ware, Inc第 6 頁Step 4 : Hole size Checkingnominal8.1（00.15）8.1*12（00.15）（+/-0.5）actual8.218.22*12.46deviation00nominalactualdeviationRps2Rps1Step 5 : ThinningREPORT CHECKING THINNESMeasure thickness request: 2mmactual thickness2mmLIMITS MAX : 22%11.8611011623748591321.9631.8441.9351.9561.8471.9181.94

5、91.92101.81111.76121.62131.74141516THINNING MAX19%12Step 6 : Appearance CheckingAppearance Checking 外觀檢查NO判定標準 Control standard檢驗方法 Methond判定 OK、NG、N/APicture1零件是否正確？ Is the rignt part?Visual目視OK2變薄率是否 料厚的 20%范 內？ THINNING MAX no more 20%Venire caliper 游標卡尺OK3是否有開裂、暗裂？ No crack,deformationVisual目視OK

6、4毛邊、毛刺、尖角是否 0.3mm 范圍內？ glitches, indenion,damaged,Venire caliper 游標卡尺OK5是否有模痕、壓傷（無手感可接受）？ No roughness detect with the handwith the handOK6是否有拉傷、劃傷？No degradation or deformation手觸 with the handOK7是否有起皺、變形（裝配面平面度需 0.2MM 以內）？No crack,deformationVisual /Venire caliper目視/游標卡尺OK8是否有生銹？Rust?Visual目視OK9字印是否正確、明顯且無手 感？Marking information crrect ?Visual/ with the hand目視/手觸OK10公差是否與 3D 公差相符？ Report tolerance is the same with 3D?檢查 checkingOK11零件定位是否與檢具定義相符？ PRS is the same with gauge?檢具 gaugeOK12料邊斷差是否超過公差帶的 50%？ Trim no moren 50%