17-01差溫?cái)D壓投稿mc response to reviews

1、Dear reviewers:ly,wereallyappreteyoursuggestionsontheprentitled“Characterization of High-strength Mg-Gd-Zn-Zr Alloys Developed by Differential-thermal Extru”, which we resubmitted for publicationhe MaterialsCharacterization. We have followed the advice and revised our manuscript and figures.Most of

2、the reviare marked in redhe manuscript and figures. The commentsfrom the two reviewers and our corresponding responses were listed as follows:-Reponses to Reviewer 1:1. The English writing of the p he text.Response: 這條不用管，r should be improved. There are some mistakes慢慢看2. Authors should avoid referr

3、ing to their obtained resultsheroduction part.Accordingly, the last part of theroduction should be revised.Response: 明哥，就是這一段要修改。3. Some basic and nethe extru“An Unusual Extruof MgGd alloys cso bereviewed in theroduction part:Texture in MgGdYZrAlloys”, Advanced Engineering Materials 18 (2016) 1044-1

4、049.Response: We added the pr titled “An Unusual ExtruTexturegGdYZr Alloys” to be the 20th reference as it is also related to extru.4. Particles presented in Fig. 2 should beidentified experimentally, and thencompared with the results foundhe literature.Response: We added a new Figure after Fig. 2 w

5、hich shows the TEM results ofthe particles and a paragraph about identifying the particles “Obvious blocky and rod-like particles can be observed in both the ITE and DTE sles. Considering theextrupros rarely changes the phase comition of the sles for its shortduration, the particles are suggested to

6、 from before the extruproses. Fig. 3shows the TEM results of the particles. The SAED pattern in Fig. 3a 33 shows theblocky particles have a face-center-cubic (fcc) structure wilattice constant of 0.72nm, which indicates the particles to be (Mg, Zn)3Gd phase 38-40. The EDS result of the particles in

7、Fig. 3c show the same results. Referring to the rod-like particles, the EDS result in Fig 3d indicate the particles are Zn-rich and Zr-rich phase. Furthermore,a lattice constant of 0.77 nm can be calculated based on the SAED pattern in Fig. 2b,whiatches the lattitructure of the Zn2Zr3 particle (tetr

8、agonal wi= 0.76 nmand c = 0.70 nm 41, 42)” at the start of the second paragraph in Section 3.2.5. The authors have used the term “solutionizing” for the heating of the castbillets before extru. This term usually apps to an annealing treatment after whichthe ssles are quenched for further heat treati

9、ng. Here, the authors have cooled theirles after this treatment, and thus, it is suggested to call this treatment as“homogenization” instead of “Solutionizing”.Response: We replaced all the “solution-treated” by “homogenized”.6. Some parts of the presults.r lack comprehensive discuss on the obtained

10、Response: 明哥，我實在看不出來這篇實驗看出來了告訴我一聲還有哪些地方要，明哥-Responses to Reviewer 21. As for the labels in Fig. 2, the authors should provide relevant eviden as XRD and EDS data.uchResponse: Thiggestion is similar to the 4th one of Reviewer 1. We added a newFigure after Fig. 2 which shows the TEM results of the par

11、ticles and a paragraph aboutidentifying the particles “Obvious blocky and rod-like particles can be observed in boththe ITE and DTE sles. Considering the extrupros rarely changes the phasecomition of the sles for its short duration, the particles are suggested to frombefore the extruproses. Fig. 3 s

12、hows the TEM results of the particles. The SAEDpattern in Fig. 3a 33 shows the blocky particles have a face-center-cubic (fcc)structure wilattice constant of 0.72 nm, which indicates the particles to be (Mg,Zn)3Gd phase 38-40. The EDS result of the particles in Fig. 3c show the same results. Referri

13、ng to the rod-like particles, the EDS result in Fig 3d indicate the particles areZn-rich and Zr-rich phase. Furthermore, a lattice constant of 0.77 nm can be calculatedbased on the SAED pattern in Fig. 2b, whiatches the lattitructure of the Zn2Zr3particle (tetragonal wiparagraph in Section 3.2.= 0.7

14、6 nm and c = 0.70 nm 41, 42)” at the start of the second2. The authors should provide high magnified images showing the morphologyof the existed LPSO phase.Response: We added a new figure (Fig. 4b now) wihigher magnification toshow the morphology of the LPSO structure. The TEM micrographs combined w

15、ith theSAED pattern are enough for proving the lamellae are the LPSO structure.3. Fig. 7 and Fig. 8 are quite similar. Only one is enough.Response: Fig. 7 shows the original represenive engineering curves of the les and the YS, UTS and elongation shown in Fig. 8 are obtained from Fig. 7.sTherefore, we think both of them are nesary. However, as both the figures are aboutthe tensile properties, we combined themo