外文翻譯--舉升機

英文原文 Lift Auto lift refers to vehicle repair industry for the lifting of the steam guarantees the equipment. Lift in automobile maintenance and curing plays a very important role, whether the vehicle overhaul, or minor repairs and maintenance, are inseparable from it, and its products have a direct impact on nature and quality maintenance personnel safety. The scale of maintenance and curing enterprises, whether maintenance range of vehicles comprehensive repair shop, or business scope single street shop (such as tire store), almost all equipped with lifting machine. From 1990s, domestic lifting machine gradually became popular in China, with the increase of auto possession, lift as an important tool for car maintenance, demand too greatly increased. Now lift market has nearly 100 Chinese and foreign brand, product series hundreds of thousands. Lift foreign famous brand has bend - Rotary, pak, domestic have antell force, million force AMREOC, jinhua (open JIG), han MaiKeSen, sequence of, yuan levy, so f, extensive force, etc. classification Foreign brands though prices higher, but rely on its product quality, stable performance, the equipment is simple, established in dealers good reputation. As in recent years the development of domestic lifting machine industry, no matter in product design, technical development or after-sales service, were a lot of improvement, sales have greatly improved. Lifting machine according to the function and shapes points, can generally be divided into, two columns, four-column, scissor three categories. use According to the function can be divided into four-wheel location type peace plate； According to occupy space can be divided into the ground type and Tibetan； The ground type, suitable for without any repair mode, some on the floor slabs not suitable to install two column lift and ordinary four-column lift, and the machine and floor surface wide, so you can drive can be installed in any of the floor above, resolve customer site problem. Scissor lift than two columns and four-column lift the biggest advantage is not taking up space, convenient use, the deficiency is fill oil balance is very strict, and the need to have control box, cost is more expensive. Four-column lift product features 1, lift up to maximum lifting height limit a switch can automatically automatically cut off the power of hydraulic pump circuit. 2, powerful high-horsepower motor. 3, lifting ability reach 350 tons. 4, safe and reliable insurance device. 5, practical design. 6, low noise, low vibration design. 7, expanded lift platform width. 8, spacious operation space. 9, 100% prevent cylinders spills. 10, electric hydraulic type second lifting. 11, import reversing valves, manual directional control, electric reversing two models to choose from. Zimu scissor lift product features 1, each lifting machine is equipped with a small cut, this small cut with the Lord with the same hydraulic balance control cut, the maximum lifting height way 400mm ascension. 2, the four-wheel location with high precision. The hydraulic oil cylinder deputy Lord of the way that the system has the following advantages: balance No link rod, work and comfortable, barrier-free, the distance between the running boards can be adjusted freely. 3 and the minimum height, can only 220mm above ground installation for reducing costs. 4, photoelectric switch detection by lifting balanced guarantees vehicle safety. 5 all the oil cylinder, equipment installed explosion-proof valve, prevent oil cylinder failure safety after a sudden decrease guarantee. The worlds first unique inversion oil cylinder two columns lifting machine In response, the independent development of countryside policy motor repair the world first inversion double oil cylinder column lift, the operation is simple, lifting machine of the space is little, the price is cheap, very appropriate in the country with TouJian pits. Lifting machine USES the principal deputy oil cylinder and lifting more stable. Unilateral manual to unlock, operation more convenient. Equipment design is exquisite, convenient installation. Equipment for 2300mm within the span only, saving field. Automatic protection turned arms. Use cross square tube, the strength of the sliding Taiwan increased by 50% or more. Lifting machine adopts maintenance-free sliding sets the slider. Powder painting, surface more luster, more durable, more durable. Lift safety operation procedures A, should remove lift before use near the fixture and sundry hamper operations, and check whether normal operating handles. Second, operating mechanism sensitive effective, hydraulic system are not allowed to have crawled phenomenon. Third, a car, four teams in same plane Angle should, adjust a horn pads height make its contact vehicle chassis support area. Four, a car, not too high, branch of the vehicle team up to lock after four bracket. Five, stay after lifting vehicles should be into lifting machine support block to adjust the model provisions are moving the lifting point. Six, lift at personnel should leave vehicles, lifting to need highly, must insert insurance locking pin, and ensure safe and reliable to start underneath the car homework. Seven, except subsidies and minor repairs project outside, other trival heavy lifter operation that may in the operation of repair. Eight, the lifter not frequent fluctuations. Nine, a car lifting want firm, landing to slow. Ten, someone operations lifting lift is strictly prohibited. Eleven, found that the operator is ineffective, not synchronous motor, bracket uneven or hydraulic parts shall promptly report, leakage of oil, not in spite of operation. Twelve, homework finished should remove debris, clean the lift around to keep site neat. Thirteen, regular (half an year) ruled out lifting oil cylinder seeper, check and the amount of oil, the oil is enough should be timely refill the same brand of pressure oil. At the same time should check lubrication, lift transmission gears and sew bar. Auto four-wheel use method and the matters needing attention One, get on preparatory work before: Tested vehicles driving on lifting machine before, needs to check whether the four wheels tire pressure conforms to the standard tire pressure. Whether badly worn tread pattern. Sure lift two bearing plate width and the tested vehicles before and after the wheelbase in line, then lift troops to its lowest point, ensure corner after the plate and the board after into fixed pin, then will be measured on lifting machine vehicles. Vehicles in lifting machine should be in front, dont make the body to askew. The two front wheel will fall vehicle in two corner, and the center of the disk on the disc to Angle plate in tire uniform distribution of both sides. Vehicle flameout, pull handcuffed brake, shake her left side, window glass driver left vehicles. Operator need forcibly pressure respectively the front and the rear bodywork, to make the vehicle suspension reset. After the installation four during production. Second, installation fixture: According to the test vehicle wheels to adjust size fixture. First LongZhao position, below two adjustment to the right size position, then adjust the length of two card arm out. The first two LongZhao below, in the top of the steel wheel, then raised outside edge, and loosen the LongZhao above the knob, adjust its position, that is also in the top of the steel wheel is raised outside, and then tighten the knob. The next step is to use his hands and promote activity in the fastener rod, to make CARDS in the wheels can card arm, then hang security within the tattoo hook, check fixtures is installed firmly. Three, installation controller is equipped: According to the corresponding four sensors installed to the wheels of the fixture position. Should pay attention to in the positioning shaft sensor to daub sparse of lubricating oil (cannot besmear butter), in order to prevent the long time after insertion caused wear, cant accurate positioning shaft installed in place, affect the measurement precision. Connecting communication cable and Angle to disk cables. The arrow on the cable plug sockets and of the arrow after, you can directly inserted. Four cable length of the difference just is different, the two root 6.5 meters cable is used for connecting controller is equipped with two fronts sensors, two 4.5 meters in the cable is mutual connection. Before and after sensor Each sensor has three socket, above two are the same, the one below is used for connecting corner plates. Cable connection good after, unplug corner after the plate and skateboard fixed pin. Give the vehicle lifting the lowest lift down the safety lock up the grid position, in order to ensure lifting platform in horizontal status. On the sensor and controller is equipped power indicator, press R key or the corresponding position key activation each sensor, after the sensor is put on the level of fixed the knob, tighten the bubble in roughly the level of position. Four, operation controller is equipped: Boot after, batch program will automatically into measurement procedures for users initial status for the next step, the operation. According to move to the next step can be F3 keys. Screen TEST, said that the system was refreshed memories of last measurement information. Then program started measuring steps. Step four main points measuring steps, the first is the measure, including preparation of the input registration forms, select models and deviation of compensation. Input the registration form: contains various customer information, can choose any want to input project, and the future of the project can be according to the input to mix the measurement results data. PaiZhaoHao or maintenance, can generally vehicles single Numbers to enter the corresponding entries for future submitted. Input information can be English letters and Numbers, no Chinese character input. Fill out the form, by F3 after entering models choose interface. Choose the corresponding to the test vehicle models, if need to do after deviation of compensation, then the advance, or press F4 F3 stop. With deviation compensation: if the fixture is used, the only one in rapid fixture serious damage degree when straps, they need to do with deviation compensation (for PassatB5 AudiA6 or before must do, measurement for deviation compensation)； If the use of peeling, the fixture since for all vehicles must do with deviation compensation. Do the deviation of compensation points: (1) tire rotation direction should be vehicles moving direction of rotation. (2) adjustment before detection: installed controller is equipped with brakes locked. Equipment Enter adjustment before detecting steps, steering wheel will appear on the screen to it pattern. In the green area, says acceptable range, but on both sides of the green range around the measurement results, can differ about five points. Therefore, it is best to in the green zone of arrows in the middle in the black. The steering wheel in the order: first, then turn right, then left 20 degrees to 20 degrees, then. Measured at the screen when the front wheel beam. According to measurements F3 button to enter the maximum rotation Angle plate, using electronic steps through the steps the controller is equipped can be automatic measure the maximum total corner. Firstly, then according to the steering wheel in errov screen, remove both front sensor. Stay screen displays the measured, after waiting for picture to the right until the steering wheel continuous play motionless, then a steady living so far not let go. Wait until after continuous measurement to the right, then play the steering wheel so until dozen dont move, and then a steady living not let go. Wait until after the end of automatic measurement, screen showed all the measurement data. Reload the two front sensor, if measured data, adjustable scope of more than allow the data, it can adjust steps into position. Positioning adjustment: do positioning adjustment before, first with a steering wheel lock will steering wheel fixed into horizontal rises again to proper adjustment of lifting machine, will lift high level security position in the lock. Adjusted for four sensors horizontal status, then operate controller is equipped into position adjustment operation. Adjust program will first display vehicles the measured value of the rear axle a parameters, if vehicle rear-axle parameters is adjustable (most vehicles rear-axle positioning parameter is unable to adjust), then the screen can consult to adjust, screen data at the data will display the current adjusted parameters data. Rear-axle positioning parameters adjustment, by F3 after may enter front axle tuning steps. Camber Angle adjustment p-s-n according to the structure of the vehicle chassis, can be divided into two kinds, one kind is need to lift shaft can be adjusted to front wheel impending camber Angle； Another kind is need not lifting front axle camber Angle can be adjusted. The need for lifting the front axle camber Angle adjustment, its position adjustment of vehicle steps as follows: 1) according to the screen F3 key until p-s-n adjust the picture. This screen also showed that the front axle of the five positioning parameter values, they were: left, right wheel, left, right, camber Angle front wheel bundle, total before former beam. Then press F7 keys, screen SVRMGR , hints you now can use second lifter will lift the front axle vehicles. In your vehicle with secondary lifting will lift shaft, then press F3 key after going forward, this screen camber Angle data right wheels. Now you can according to the screen display camber Angle adjustment data. 2) adjust the left, right after the camber Angle, wheel, then according to the F3 keys on the screen can now will be second lifting down clew, right now can put down second lifting, when vehicles in lift platform front fell steadily honked vehicle front axle after the suspension parts, down a few times, to make the vehicle suspension reset p-s-n. Vehicles put good, then press, when screen F3 keys back on the front axle adjust the picture. 3) can now, adjust the picture in front of the left and right according to show about former bunch of value adjustment round wheels. Before bundle When former bundles and a total right wheels are well adjusted before beam and press F4 keys end positioning adjustment process. 4) to need not lifting front axle camber Angle adjustment, then can the vehicle in front axle, adjust the picture camber Angle adjustment according to the first, and then the order and beam before adjust reference screen real-time display, the parameters of the value adjusted respectively camber Angle, or so ago about values. Bundle Adjusted by F4, after adjustment process end positioning. Adjusted to detect: lifting when measuring the troops back to adjust the height of before, will lift the lock in horizontal safe place. Enter adjusted, when measured steps showed on the screen of the two front current value. Before alone bundle According to the remaining steps forward, F3 adjustment before testing steps with same. If on the steps of the two front wheel display before alone adjustment process and the position of the beam value in former bunch of value adjustment good have bigger difference, the reason probably because in after adjustment, the process of vehicle fell down, the steering wheel position changed, killing the two front wheel position change. So each wheel alone with former bunch of value orientation for the adjustment of different values, but front wheel wont change. Total former bundle But because after adjusting when entering test shown before the front wheel of single beam value will be record and the final measurement results, which makes the displayed in the front wheels alone adjustment results report before may bundle value unqualified. But the reality is front wheel always is qualified, former beam steering wheel not only because to former bunch of value in allowing alone outside its range. To prevent this appear, in adjusted, if found in measuring steps each wheel shown before alone adjustment and the position of the beam value is not the same as the value, according to a larger F3 forward, to the screen in until after the steering wheel in here is on, steering wheel. Then press F4 key exit after adjusting the detecting steps, then re-enter adjusted detecting steps. Right now because of the previous step to the steering wheel, so should be displayed on the screen of the steering wheel in cases before beam value, the value of just what we need. If former bunch of value in the permissible, indicates that location adjustment qualified, if the former bunch of value is still not qualified, indicates that a step up positioning adjustment is not ready, still need to be adjusted step back to the positioning again again adjustments. Finally shows measurement adjustment results are given statements adjustment before measured values, and the measured value standard after adjusting to adjust for after the final result measurements. Therefore, if the measurements, after adjusting the parameters of the existing can adjust the data is unqualified, it will need to return to the localization tuning steps to adjust. To move the cursor moves to measure the printer icon adjustment results statements position, then press the return key confirmed that can print a complete measuring adjustment results report. After printing, the measured results will be preserved for later can shifting gear query. If not print, then measured results data would be lost. If you want to save the measurement data, and dont want to print, can be in print before closing printer, again printing operations. The system will automatically generate printed documentation, then switch printers, if the system found printer is closed and error will appear on the screen, dont worry, this measurement results have been preserved. 中文譯文 舉升機 汽車舉升機是指汽車維修行業用于汽車舉升的汽保設備 。舉升機在汽車維修養護中發揮著至關重要的作用，無論整車大修，還是小修保養，都離不開它，其產品性質、質量好壞直接影響維修人員的人身安全。在規模各異的維修養護企業中，無論是維修多種車型的綜合類修理廠，還是經營范圍單一的街邊店（如輪胎店），幾乎都配備有舉升機。 汽車舉升機是指汽車維修行業用于汽車舉升的汽保設備。舉升機在汽車維修養護中發揮著至關重要的作用，無論整車大修，還是小修保養，都離不開它，其產品性質、質量好壞直接影響維修人員的人身安全。在規模各異的維修養護企業中，無論是維修多種車型的綜合類修理廠，還是經營 范圍單一的街邊店（如輪胎店），幾乎都配備有舉升機。 從 20 世紀 90 年代開始，國內舉升機逐漸開始普及，隨著我國汽車保有量的增加，舉升機作為汽車維修的重要工具，需求量也大大增加?，F(xiàn)在舉升機市場已經擁有近百個中外品牌，產品系列成百上千。 舉升機國外著名的品牌有 bend-pak， Rotary 等，國內有安特力、萬力開 AMREOC、金華（ JIG）、漢麥克森、序達、元征、鰲福、廣力等。 分類 國外品牌盡管價格較高，但依靠其產品質量好、性能穩定、設備操作簡單，在經銷商中建立了良好的口碑。隨著近幾年國內舉升機行業的發 展，無論在產品設計、技術開發還是售后服務方面，都進行了很多的改進，銷量也大大提高。 舉升機按照功能和形狀來分，一般可分為，兩柱，四柱，剪式三大類。 用途 按照功能可分為四輪定位型和平板式；按照占用的空間不同可分為地上式和地藏式；地上式無需挖槽，適用于任何修理廠，有一些樓板上不適合安裝二柱舉升機以及普通四柱舉升機，而本機器與樓板接觸面廣，這樣可以安裝在任何可以開車的樓板上面，解決客戶場地問題。剪式舉升機比兩柱和四柱舉升機最大的好處是不占用空間，方便使用，不足之處則是補油平衡要求很嚴格，而且需配備控制箱， 造價較貴。 四柱舉升機產品特點 1、舉升機上升到最大舉升高度時限位開關會自動斷電、自動切斷液壓泵里的油壓回路。 2、大馬力的強有力電機。 3、舉升能力達到 3.5 噸。 4、安全可靠的保險裝置。 5、實用性設計。 6、低噪音，低振動設計。 7、擴大的升降臺寬度。 8、寬敞的作業空間。 9、 100%防止油壓缸漏油。 10、電動液壓式二次舉升。 11、進口換向閥、手動換向、電動換向 兩種機型可供選擇。 子母剪式舉升機產品特點 1、每個舉升機配備一個小剪，該小剪用與主剪相同的液壓平衡控制方式，最大舉升高度提升 400mm。 2、可配置高精密的四輪定位。主副油缸的液壓方式保證系統的平衡，具有以下優點： 無連接桿，工作舒適，無障礙，跑板間距離可隨意調整。 3、本機最低高度僅為 220mm，可地面安裝減少費用。 4、可通過光電開關檢測舉升是否平衡，可保證車輛安全。 5、設備上所有油缸都安裝了防爆閥，防止油缸失效后突然下降保證人身安全。 世界首創獨一無二的倒置油缸兩 柱舉升機 ECO1122 為響應汽修下鄉政策，獨立開發的世界首創倒置油缸雙柱舉升機，本舉升機操作簡單，占空間小，價格低廉，非常合適在鄉村投建維修站用。 舉升機采用主副油缸，升降更加平穩。 單邊手動解鎖，操作更方便。 設備設計精巧，安裝方便。 設備內跨距僅為 2300mm，節約場地。 自動防轉支臂。 使用十字方管，滑臺的強度提高 50%以上。 舉升機采用免保養的滑臺滑塊。 粉末烤漆，表面更 光澤、更持久、更持久。 舉升機安全使用操作規程 一、使用前應清除舉升機附近妨礙作業的器具及雜物，并檢查操作手柄是否正常。 二、操作機構靈敏有效，液壓系統不允許有爬行現象。 三、支車時，四個支角應在同一平面上，調整支角膠墊高度使其接觸車輛底盤支撐部位。 四、支車時，車輛不可支的過高，支起后四個托架要鎖緊。 五、待舉升車輛駛入后，應將舉升機支撐塊調整移動對正該車型規定的舉升點。 六、舉升時人員應離開車輛，舉升到需要高度時，必須插入保險鎖銷，并確保安全可靠才可開始車底作業。 七、除低保及小修項目外，其他繁瑣笨重作業，不得在舉升器上操作修理。 八、舉升器不得頻繁起落。 九、支車時舉升要穩，降落要慢。 十、有人作業時嚴禁升降舉升機。 十一、發現操作機構不靈，電機不同步，托架不平或液壓部分漏油，應及時報修，不得帶病操作。 十二、作業完畢應清除雜物，打掃舉升機周圍以保持場地整潔。 十三、定期（半年）排除舉升機油缸積水，并檢查油量，油量不足應及時加注相同牌號的壓力油。同時應檢查潤滑、舉升機傳動齒輪及縫條。 汽車四輪定位儀的使用方法及注意事項 一、 上車前準備工作： 在被測車輛開上舉升機之前，需要檢查四個車輪的胎壓是否符合標準胎壓。輪胎花紋是否嚴重磨損。確定舉升機兩個承載板的寬度與被測車輛的前、后軸距一致，然后將舉升機降至最低點，確保轉角盤和后滑板的固定銷都插好之后，再將被測車輛開上舉升機。車輛在舉升機上應處于正前方向，不要使車身歪斜。車輛的兩前輪要落在兩轉角盤的中心上，同時轉角盤的圓盤要均勻分布在輪胎的兩側。車輛熄火后，拉上手剎，搖下左前側車窗玻璃，司機離開車輛。操作員需要分別用力壓車身的前部和后部，以使車輛的懸掛復位。之后是安裝四個卡具。 二、安裝卡具： 根據所測車輛的車輪尺寸對卡具進行調整。首先調整下方兩個尼龍爪位置到合適的尺寸位置，然后調節兩個卡臂的伸出長度。先將下方的兩個尼龍爪頂在鋼圈的凸起的外沿，然后再松開上方尼龍爪的旋鈕，調整它的位置，使之也頂在鋼圈的凸起的外沿，然后再擰緊旋鈕。下一步是用兩手同時推動卡具上的活動桿，使卡臂能夠卡在輪紋內，然后掛上安全鉤，檢查卡具是否安裝牢固。 三、安裝定位儀： 將四個傳感器按照對應車輪的位置安裝到卡具上。要注意在傳感器的定位軸上要涂抹稀的潤滑油（不能涂黃油），以防止長時間插拔后 造成定位軸磨損，無法準確安裝到位，影響測量精度。連接通訊電纜和轉角盤電纜。把電纜插頭上的箭頭和插座上的箭頭標記對好之后，就可以直接插入。四根電纜的差別只是長度不同，兩根 6.5 米的電纜是用來連接定位儀和兩個前輪上的傳感器，兩個 4.5 米的電纜是在前后傳感器之間互相連接。每個傳感器上有 3個插座，上面兩個是完全一樣的，最下面的一個是用來連接轉角盤。電纜連接好之后，拔掉轉角盤和后滑板上的固定銷。將車輛舉升后落到舉升機最低一格的安全鎖止位置，以保證舉升平臺處在水平狀態。定位儀開機，傳感器上的電源指示燈亮，按 R 鍵或相應的 位置鍵激活各個傳感器，把傳感器上放水平后擰緊固定旋鈕，水平氣泡處在大致中央的位置。 四、操作定位儀： 開機之后，批處理程序會自動進入測量程序的初始狀態，等待用戶進行下一步的操作。按 F3 鍵可前進到下一步。屏幕上出現“ TEST”，表示系統正在刷新所記憶的上次測量的信息。然后程序開始測量步驟。測量步驟主要分四步，首先是測量前的準備工作，包括輸入登記表格，選擇車型和偏位補償。輸入登記表格：包含了各項客戶信息，可以任意選擇要輸入的項目，并且將來可以根據所輸入的項目來調出