西威變頻器參數設置表

1、西威變頻器參數設置表WVF銅步電梯控制柜配西威變頻器參數設置表(多段速方式)三st ,Drive data:spd ref/fbk res 0.03125rpm1:電機參數(Motor data )參數設定值說明額定電壓(Rated boltage )380V參數參考頭際額定電流(Rated current )12.8A參數參考頭際額定轉速(Rated current )96參數參考頭際極對數10參數參考頭際疋子電阻( stator resista nee)0.8疋子電感(lss in ducta nee )0. 020H轉矩常數(Torque constant )18. 210NM/A設小了

2、會限制電反電勢常數(EMF constant)10. 5142：曳引機參數( Mechanical data )參數設定值說明速度單位選擇(Travel units sel)millimerers減速比(Gearbox ratio )2曳引輪直徑(P ulley dlameter )410mm*最大轉速范圍(Full scale speed )150rpm*3:轎廂重量參數(Weights)參數設定值說明轎廂重量(Cabin weight )1100kg*對重重量(Load weight )1500kg*最大載重量(Load weight )800kg*鋼繩重量(Rope weight )30

3、0kg*電機慣量(Motor inertia)5.0*減速箱慣量(Gearbox inertia )0.0*4:編碼器參數(Encoders config )參數設定值說明編碼器類型(Speed fbk sel )0(std en coder)標準編碼器類型(Std enc type )4(S inu soidals in cos)標準編碼器脈沖(Std enc pulses )2048pps標準編碼器模式(Std dig enc mode )0(FP)標準編碼器電源(Std enc supply )0(5.14v)5:制動單元參數(BU protectlon )參數設定值說明制動單元控制(B

4、U control )1(i ntern al)制動電阻(BU resista nee )70*制動電阻功率(BU resista nee )2.0KW*6:控制模式參數(Regulation mode )參數設定值說明控制模式選擇(Regulation )4(Brushless)7:多段速參數(Speed profile )參數設定值說明平滑啟動速度(Smooth start speed )5mm/s自學習速度(Multi speed 1)300mm/s檢修速度(Multi speed 2)300mm/s爬行速度(Multi speed3 )50mm/s速度 4 (Multi speed 4

5、 )0mm/s速度 3 (Multi speed 5 )0mm/s速度 2 (Multi speed 6 )800mm/s額定速度(Multi speed 7 )1000mm/s8:斜坡曲線參數(Ramp profile )參數設定值說明初始急加速(MR0 aee ini jerk )300mm/s加速度(MR0 aeeeleration )600mm/s末端急加速(MR0 aee end jerk )3500mm/s初始急減速(MR0 dee ini jerk )3500mm/s減速度(MR0 deeeletation )600mm/s末端急減速(MR0 dee end deeel )350

6、0mm/s結束時減速度(MR0 end deeel)2200mm/s9:電梯時序參數(Lift sequenee )參數設定值說明接觸器閉合延時(Cont elose delay )304ms抱閘打開延時(Brake open delay )416ms平滑啟動延時(Smoothstart delay )400ms抱閘閉合延時(Brake elose delay )680ms接觸器打開延時(Cont open delay )200ms10：速度 PI 參數(Speed reg gains )參數設定值說明SpdPIgain%20%SpdIIgain%3.3%SpdP2gain%20%SpdI2g

7、ain%5%SpdP3gain%80%SpdI3gain%12%Sped 0en able2( Enable as start )Sped 0 P gai n%19%-30%Sped 0 I gain%20%濾波時間(Prop Filter )1.5ms11:速度閾值參數(Speed threshold )零速閾值參考(Spd 0 ref thr )2rpm零速閾值參考延時(Spd 0 ref delay)500rpm零速閾值(Spd 0 speed thr )2rpm零速延時(Spd 0 spd delay )500rpm閾值(SGP tran 21 h thr )94%閾值(SGP tran 32 thr )5%帶寬(SGP tran 21 band )4%帶寬(SGP tran 32 band )4%12:慣量補償參數(Inertia compensate )參數設定值說明慣量補償使能(Inertia comp en )1 (En able)初始慣量(Int inertia)260.6764kgm13:速度 PI 規劃參數(Speed regulator )參數設定值說明速度 P 基準值(Spd Pbase value