西門子培訓例題設計合集cp4435ext manual

1、該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：SIMATIC NETS7CPs for PROFIBUS CP 443-5 Extended6GK7 443-5DX03-0XE0Version 2 and higher (Firmware version V5.0 and higher) for SIMATIC S7-400 / S7-400HStatus and fault LEDsMode selectorPROFIBUS interface (9-pin sub-D female connector)該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Notes on the

2、ProductNotes on the ProductNoteAll the notices in the Product Information Bulletin shipped with this device are valid and must be adhered to.Compatibility with the Previous VersionNoteMake sure that you read the information regarding extended functionality and restrictions in Chapter 6 of this manua

3、l!CP 443-5 Extended for PROFIBUS / Manual Part B4Release 2/2003C79000-G8976-C162-04B42該文檔是極速PDF編輯器生成，如果想去掉該提示,請te并：ContentsContents Part APROFIBUS CPs General Information . . . . . . . . . . . . . .See General PartNotePlease remember that Part A of the manual also belongs to the description of the C

4、P. Among other things, it contains explanations of the safety notices and general information that applies to all S7 CPs for PROFIBUS.You can also download this general part from the Internet:Contents Part B412Features / Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5、. . . . . . . . . . . . .Requirements for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B44 B48 B49 B410 B412 B414 B416 B416B4162.12.2Use with the Current CPU Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Converting older System

6、s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .345Installation and Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Displays and Mode Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Performance Da

7、ta . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Supported Transmission Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Characteristics of the DP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ch

8、aracteristics of S5-compatible Communication (SEND/RECEIVE Interface)over FDL Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Characteristics of S7 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . .Parallel Use of Communications Services (M

9、ultiprotocol Operation) . Time-of-day Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Data Record Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Use in Fault-tolerant Systems 1) . . . . . . . . . . . . . . . . . . . . . .

10、 . . . . . . . . .Other Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Restricted Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B45.10B419 B419 B421 B421 B422 B423 B424 B426 B426 B427

11、B4286Compatibility with the Previous Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.16.2Extended functionality Compared with Previous Product: . . . . . . . . . .Replacing Older Modules / Replacing Defective Modules . . . . . . . . . .7Technical Specifications . . . . . . . . .

12、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CP 443-5 Extended for PROFIBUS / Manual Part B4 Release 2/2003C79000-G8976-C162-04B13該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Features / Services1Features / ServicesApplicationThe CP 443-5 Extended communications processor is designed for use

13、 in a SIMATIC S7-400 (standard) and S7-400H (fault-tolerant system) programmable controller. It allows the S7-400 / S7-400H to be connected to a PROFIBUS fieldbus system.You can use the CP as a router for data records intended for field devices (for example PA slaves). One tool that creates such dat

14、a records for assigning parameters to field devices is SIMATIC PDM (Process Device Manager).ServicesThe current version of the CP 443-5 Extended supports the following communication services in the standard and H systems: PROFIBUS-DP with the following characteristics:DP master (class 1) (redundant

15、operation in fault-tolerant system also possible)Direct data exchange (DP slave to DP slave)As a DP master, the CP 443-5 Extended is capable of enabling direct data exchange for “its” DP slaves.SYNC /FREEZE (please refer to Tables 2-1 and 2-2)The outputs or inputs can be synchronized from the within

16、 the user program using system function SFC11.Constant bus cycle time (only in the standard system)The ability to set a constant bus cycle time means that the DP master always starts the DP bus cycle after the same interval.Selectable DP modes:(For more information on the topic of DP-V1, refer to th

17、e STEP 7 / Hardware Configuration online help)CP 443-5 Extended for PROFIBUS / Manual Part B4Release 2/2003C79000-G8976-C162-04B44DP-V1 functionality (default in STEP 7)S7-compatibleDP master mode for: DP slaves complying with the PROFIBUS DP-V0 and DP-V1standard Siemens DP slaves(Refer to the infor

18、mation in Tables 2-1 and 2-2 on the required CPU)DP master mode for: DP Slaves complying with the PROFIBUS DP-V0 standard (DP slaves complying with the DP-V1 standard can only be used with restricted functionality) Siemens DP slaves該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Featurevic CiR (Configuration in RUN) in

19、the standard systemBy making a change to the configuration with CiR (Configuration in RUN), it is possible to put a DP slave / DP slot extension into operation or take it out of operation when necessary while the system is running.In other words, you can configure and activate additional DP slaves o

20、r DP slots while the S7 station is in RUN. Activate/deactivate DP slaves in the standard systemDP slaves can be activated and deactivated from the within the user program using system function SFC12.S7 communication and PG/OP communication PG functions with upload / download of FM modules, configura

21、tion / diagnostics and routingNote on routing: Dynamic switchover to alternative paths (for example if there is a problem on one of the possible transmission paths) is not supported.Operator control and monitoring functions (HMI)Client and server for data exchange on S7 connections via communication

22、s function blocks (fault-tolerant S7 connections also possible)1)Download S7 connections and gateways in RUN. S5-compatible communication (SEND/RECEIVE interface) on FDL connections of the following types:specified FDL connections free layer 2 connections broadcastmulticast1)Blocks for S7 communicat

23、ion (see also STEP 7 online help or“System Software for S7-300/400 System and Standard Functions” manual):BSEND BRCV PUT GET USEND URCV START STOP RESUME STATUSUSTATUS CONTROLSFB 12SFB 13SFB 14SFB 15SFB 8SFB 9SFB 19SFB 20SFB 21SFB 22SFB 23SFC 62CP 443-5 Extended for PROFIBUS / Manual Part B4 Release

24、 2/2003C79000-G8976-C162-04B45該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Features / Services Time-of-day synchronization via PROFIBUSThe CP forwards time-of-day synchronization frames from the LAN to the station (CPU = time slave) or from the station to the LAN (CPU= time master) or this station is synchronized via

25、 a different LAN and thetime-of-day synchronization frame must be forwarded over PROFIBUS for the synchronization of further stations.The CP supports time stamping of distributed process signals in conjunction with the IM 153.Time-of-day status value (standard/daylight saving time switchover, synchr

26、onization status) Data record routingYou can use the CP as a router for data records intended for field devices (for example PA slaves). One tool that creates such data records for assigning parameters to field devices is SIMATIC PDM (Process Device Manager; see also SIMATIC PDM documentation.).The

27、services of the CP 443-5 Extended module listed above can be used at the same time.ConfigurationTo be able to configure and use the full functionality, you must work with STEP 7 V5.2 or higher; for FDL connections and diagnostic functions the NCM S7 PROFIBUS optional package, supplied with STEP 7 mu

28、st be installed.It is possible to configure over the MPI or LAN/PROFIBUS.Note the following features and differences depending on the version you are using: STEP 7 version 5.0 Service Pack 3This version is the minimum requirement for the routing of PG functions, time-of-day synchronization, and data

29、 record routing.The optional package “SIMATIC S7 H Systems” must also be installed to configure fault-tolerant systems.The following functions of the CP are not yet supported in this configuration environment when using fault-tolerant systems: Single (non-redundant) communications connections cannot

30、 be configured in a fault-tolerant system;STEP 7 version 5.1 Service Pack 3When configuring fault-tolerant systems you must also install the “SIMATIC S7 H Systems” optional package.Required for DP-V1 functionality. STEP 7 version 5.2All the functions described can be used. CP 443-5 Extended for PROF

31、IBUS / Manual Part B4Release 2/2003C79000-G8976-C162-04B46該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：FeaturevicProgramming Using BlocksFor some communication services, there are “off-the-peg” blocks (FCs/FBs) available that implement the interface in your STEP 7 user program. You will find a detailed description of

32、 these blocks in the NCM S7 for PROFIBUS manuals.NoticeWe recommend that you always use the latest block versions for all module types.You will find information on the latest block version and links to download the current blocks in our Customer Support on the Internet:If you are using older block t

33、ypes, this recommendation only applies if you also have the latest firmware version.You will find further information and Internet addresses in the Preface of the General Part of this manual.Replacing Modules without a Programming DeviceWhen installing the CP 443-5 Extended, the configuration data o

34、f the CP are always stored in the CPU. Therefore replacing modules is possible without having to download the configuration data from the PG.The stored configuration data is protected from power outage by battery backup or by plugging an EPROM card into the CPU.CP 443-5 Extended for PROFIBUS / Manua

35、l Part B4 Release 2/2003C79000-G8976-C162-04B47該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Requirements for Use2Requirements for UseThe CP 443-5 Extended V 5.0 described here is supported by all CPU operating systems in the versions listed in Tables 2-1 and 2-2 below.NoticeET 200M devices that were assigned to SYNC/

36、FREEZE groups with STEP 7,must not have modules of the type FM or CP inserted.From the table, you can see which functionality is supported when you use the CP 443-5 Extended V 5.0 with the various CPU types: CPU type, order number and version Option of multicomputingThe number of CPs that can be ope

37、rated with one CPUTheum number of external DP chains of an S7 station;The number of AG-SEND or AG-RECV calls on the SEND/RECEIVE interface that can be active at the same time (data exchange on FDL connections over PROFIBUS and corresponding connections over Industrial Ethernet).Whether the CPU suppo

38、rts SYNC/FREEZE functionality via the CP.Whether the CPU supports the activate / deactivate DP functionality via the CP. DP-V1 functionalityThis also indicates how the DP mode (DP-V1 or S7-compatible) can be set in the S7 station: By chain (bc):The DP mode can be set separately for each DP master sy

39、stem By station (bs):The DP mode can only be set for all DP master systems of the S7 station.CiR functionality (DP slave / DP slot, configurable extension) CP 443-5 Extended for PROFIBUS / Manual Part B4Release 2/2003C79000-G8976-C162-04B48該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Requiremr U2.1Use with the Curren

40、t CPU TypesWhen operating the CP 443-5 Extended V 5.0 with the CPU types listed here in the table, the following functionality is supported without exception: Number of operable CPs: 14um number of external DP chains per station: 10 Multicomputing (except for CiR and H systems)Table 2-1Use with the

41、Current CPU TypesCP 443-5 Extended for PROFIBUS / Manual Part B4 Release 2/2003C79000-G8976-C162-04B49CPUOrder numberFirmware versionNumber of AG-SEND or AG-RECV calls at same timeSYNC/FREEZEfunctionalityDP-V1functionality 1)CiR functionalityActivate / deactivate DP slaveCPU 4126ES7412-1XF03-0AB0As

42、of V3.024 / 24yesyes (bs)nonoAs of V3.124 /24yesyes (bc)yesyesCPU 412-26ES7412-2XG00-0AB0As of V3.024 / 24yesyes (bs)nonoAs of V3.124 / 24yesyes (bc)yesyesCPU414-2 128 KB6ES7414-2XG03-0AB0As of V3.024 / 24yesyes (bs)nonoAs of V3.124 / 24yesyes (bc)yesyesCPU414-3 384 KB6ES7414-3XJ00-0AB0As of V3.024

43、/ 24yesyes (bs)nonoAs of V3.124 / 24yesyes (bc)yesyesCPU414-4H6ES7414-4HJ00-0AB0As of V3.024 / 24noyes (bs)no 2)noAs of V3.124 / 24noyes (bc)yes 2)noCPU 416-20.8 MB6ES7416-2XK02-0AB0As of V3.064 / 64yesyes (bs)nonoAs of V3.164 / 64yesyes (bc)yesyesCPU 416-31.6 MB6ES7416-3XL00-0AB0As of V3.064 / 64ye

44、syes (bs)nonoAs of V3.164 / 64yesyes (bc)yesyesCPU416F-21.6 MB6ES7416-2FK02-0AB0As of V3.164 / 64yesyes (bc)yesyesCPU417-46ES7417-4XL00-0AB0As of V3.064 / 64yesyes (bs)nonoAs of V3.164 / 64yesyes (bc)yesyes該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Requirements for UseTable 2-1Use with the Current CPU Types, contin

45、ued1) Legend:bs = by station: The DP mode can only be set for all DP master systems of the S7 station bc = by chain: The DP mode can be set for each DP master system independently2) Configuration changes in RUN are possible with this CPU.2.2Converting older SystemsThe discontinued CPUs listed in Tab

46、le 2-2 support the following functionality in conjunction with the CP 443-5 Extended V 5.0: No DP-V1 functionalityNo CiR functionality (DP slave, configurable expansion) um number of external DP chains per station: 4Number of operable CPs: 8MulticomputingCP 443-5 Extended for PROFIBUS / Manual Part

47、B4Release 2/2003C79000-G8976-C162-04B410CPUOrder numberFirmware versionNumber of AG-SEND or AG-RECV calls at same timeSYNC/FREEZEfunctionalityDP-V1functionality 1)CiR functionalityActivate / deactivate DP slaveCPU417-4H6ES7417-4HL00-0AB0As of V2.164 / 64nonono 2)no6ES7417-4HL01-0AB0As of V3.064 / 64

48、noyes (bs)no 2)noAs of V3.164 / 64noyes (bc)yes 2)no該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Requiremr UTable 2-2Use with Discontinued CPU TypesCP 443-5 Extended for PROFIBUS / Manual Part B4 Release 2/2003C79000-G8976-C162-04B411CPUOrder numberVersionNumber of AG-SEND orAG-RECV calls at same timeSYNC/FREEZEfunct

49、ionalityCPU 4126ES7 412-1XF01-0AB02 or higher12 / 12no6ES7 412-1XF02-0AB02 or higher12 / 12yesCPU 4136ES7 413-1XG01-0AB02 or higher12 / 12no6ES7 413-1XG02-0AB01 or higher12 / 12yesCPU 413-26ES7 413-2XG01-0AB02 or higher12 / 12no6ES7 413-2XG02-0AB01 or higher12 / 12yesCPU414-16ES7 414-1XG01-0AB02 or

50、higher12 / 12no6ES7 414-1XG02-0AB02 or higher12 / 12yesCPU 414-2128 KB6ES7 414-2XG01-0AB02 or higher12 / 12no6ES7 414-2XG02-0AB02 or higher12 / 12yesCPU 414-2384 KB6ES7 414-2XJ00-0AB04 or higher12 / 12no6ES7 414-2XJ01-0AB02 or higher12 / 12yesCPU416-16ES7 416-1XJ01-0AB02 or higher32 / 32no6ES7 416-1

51、XJ02 0AB01 or higher32 / 32yesCPU 416-20.8 MB6ES7 416-2XK00-0AB04 or higher32 / 32no6ES7 416-2XK01-0AB01 or higher32 / 32yesCPU 416-21.6 MB6ES7 416-2XL00-0AB04 or higher32 / 32no6ES7 416-2XL01-0AB01 or higher32 / 32yes該文檔是極速PDF編輯器生成，如果想去掉該提示,請并：Installation and Commissioning3Installation and Commiss

52、ioningCautionThe CP 443-5 Extended must not be plugged in or removed when the power is connected.If you do remove or insert the CP while it is powered on, the CPU changes to STOP; this does not cause damage to the CP. Afterwards, you must turn the power for the central rack off and on again. ! Proce

53、dure / StepsTable 3-1CP 443-5 Extended for PROFIBUS / Manual Part B4Release 2/2003C79000-G8976-C162-04B412StepExplanation / Meaning1. Insert the CP 443-5 ExtendedThe CP 443-5 Extended can be inserted in all racks with slots for P and K bus attachment: Central rack CR2, CR3 Universal rack UR1 UR2 or

54、UR2H as the centralor expansion rack with rack no. 16 (only possible if there is no DP operation).NoteWhen you are using PROFIBUS-DP, the module must only be operated in the central rack!When using the universal rack as an extension rack, you require an IM with a communication bus link!The CP 443-5 Extended cannot be used in an ER1 or ER2 expansion rack.Suitable slots in the rack:With the except