鋼結構詳圖設計標準

1、The Standard of Shop Drawing For Steel Structure鋼結構詳圖設計標準第一章 General Note總則The standard is applicable for steel structure work such as bridges, ocean platform, architecture, etc., The standard should be carried out unless especial requirements of Owner. The standard forced to define the common of sh

2、op drawings. Shop drawings of specific project may vary with facilities and fabrication capacity of shop. The intent of the standard is to make detail design of steel structure and management standardization, high quality and unification.本標準適用于橋梁、海洋工程、建筑等鋼結構工程。自本規定頒發后，如業主無特殊要求，均需按本規定執行。本規定對車間圖紙的共通部分

3、做了強制規定，具體項目的車間圖紙內容可隨工廠的設備及制造能力的不同而變化。本規定的目的是使鋼結構詳圖設計和管理標準化、高質量化及統一化。第二章 Primary Requirements基本要求2.1 The Significance of Detail Design詳圖設計的重要性Any fabrication and assembly of steel structure should equip technical personnel who have excellent diathesis. Shop drawing design branch is its core. The qual

4、ity of shop drawing will direct affect the branch of fabrication, purchasing, QC, etc. It will bring great influence to schedule even.任何鋼結構的制造和安裝都需要有一支素質優良的技術人員隊伍。深化設計部門是其中的核心。深化圖紙的質量將直接影響到制造、采購、質檢等部門，甚至?xí)て诋a(chǎn)生重大影響。2.2 Content of Detail Design詳圖設計的內容The chief task of detail design is to plot initial

5、design of steel structure put forward by architect and structural engineer to detail of construction. It contains connection strength design, shop working drawing, assembly drawing, parts drawing, material bill, typesetting drawing, etc. It may vary with various requirements of project. It must cont

6、ain data and note required by fabrication. The design personnel can show the fabrication requirements such as cutting of members, hole-punching manner, bolts, weld joint through drawing paper, lineation, sizes and notes.詳圖設計的主要任務是將建筑工程師和結構工程師提出的鋼結構初步設計進一步繪制成施工詳圖，工作內容主要為連接節點強度設計、車間加工圖、安裝布置圖、零件圖、材料清單、

7、排板圖等內容，具體可能隨項目的要求不同而有所改變。詳圖內必須包含制造所必須的數據和說明。設計人員可通過圖紙、線條、尺寸和注釋等，標明構件的切割、打孔方式、螺栓、焊縫等制造要求2.3 Process Relation between Detail Design and Fabrication, Assembly詳圖設計與制造、安裝等的工藝關系Detail design is very important segment in project. It restrict and promote with every craft branch. Design personnel should full

8、y know the recent specification, shop fabrication and field erection requirements. It should not only know the physical property, other speciality and structure where connected with steel structure, construction method, procedure, but also understand the bid of steel structure and contract definitio

9、n. Relevant design will not meet steel structure fabrication enterprise requirements until wholly mastering the knowledge above.詳圖設計是項目中極為重要的環節，與各工藝部門之間是相互制約相互促進的關系。詳圖人員必須充分了解最新的工程規范、工廠制造和現場安裝的要求。不僅需要了解鋼材的物理特性、其它專業與鋼結構相連接處的構造及施工方法、施工流程，還需要懂得鋼結構工程投標和簽訂合同等方面的知識。只有充分具備了以上知識，相應的設計才會滿足鋼結構制造企業的要求。2.4 Soft

10、ware軟件Checking computations of structure and point analyse.結構驗算和節點分析 SAP、MIDAS、ANSYS、EXCELGeneral drawing普通圖 AutoCADDetail drawing詳圖 X-STEEL、AutoCAD、SOLIDWORK第三章 Drawing and Numbering System圖紙及編號系統3.1 Unit System單位制 All drawings released to base shall be metric sizes. If contract document defines th

11、at it must be inch sizes, dimension metric sizes and inch sizes on the drawings.所有下發至基地的圖紙全部采用公制尺寸。若合同文件規定必須使用英制尺寸，則圖紙上應同時標注公制和英制尺寸。3.2 Sheet Size and Layout圖幅尺寸和布局3.2.1 Drawing size and suggested location圖紙大小及推薦使用部位A0：840*1188 general layout總布置圖 A1：594*840A2：420mm*594mm member drawing構件圖 A3：297mm*4

12、20mmA4：210mm*297mm parts drawing零件圖3.2.2 Clearance of inner and outer sheet boundary內、外圖框間距：A0：left border左邊界50mm ，rest border其余邊界20mm A1：left border左邊界40mm ，rest border其余邊界15mmA2：left border左邊界25mm ，rest border其余邊界10mm A3：left border左邊界20mm ，rest border其余邊界5mmA4：left border左邊界15mm ，rest border其余邊界5

13、mm3.2.3 Content of header area圖標區內容 Header area usually adopts company standard title which contain all requirements defined by Owner and locate at the right lower of the drawing. It can be properly revised if Owner have additional requirements. The header area should contain the information of proj

14、ect and version, technical personnel, company information. Space 50mm×75mm room to review and signet at the left of title.圖標區一般情況下采用公司的標準圖標，應包含業主明確的所有要求信息并布置在圖紙的右下方。如業主另外有要求可適當修改。圖標區要包含項目信息 、版本信息、技術人員、公司信息等內容。圖標左側要預留尺寸為50mm×75mm左右的空間以供審圖蓋章使用。3.2.4 Figure color and setting圖形顏色及設置The lineati

15、on of inner and outer sheet boundary is black, the title district is uniform style(unless additional requirements of Owner).內外圖框的線條均采用黑色，圖標區采用統一格式（除非業主另有要求）3.2.5 Drawing medium圖紙媒介a.Electronic documents and final shop drawings submitted to Owner is TIFF or PDF approved by Owner.提供至業主方的電子文檔和最終加工圖為業主同

16、意的TIFF或PDF格式。b.Hard copy should be printed half. Print all when applicable(half is preference).復印件應縮半打印。若規范要求，則全紙打?。ㄊ走x縮半打印）。c.The final copy version should meet every code: paper, vellum, film. The electronic document to be made for CD is better and may be used for respective contract.最終的復印版本應符合每個規范

17、：紙張、仿牛皮紙、底片或膠片。制作成CD的電子文檔是較好的而且可以使用在各自的合同上。3.3 Drawing Scale圖紙比例尺a.Set shop drawing scale as follows:車間圖紙比例尺設定參考如下 plan平面圖 A1 1:50 1:100 1:150 1:200 1:300 1:500 1:600 1:1000 elevation立面圖 A1 1:50 1:100 1:150 1:200 1:300 1:500 1:600 1:1000 joint standard drawing節點標準圖 A1 1:2 1:5 1:10 1:20 1:30 weld sta

18、ndard drawing焊接標準圖 A1 1:5 1:10 1:30 1:50 lifting standard drawing吊裝標準圖 A1 1:10 1:20 1:30 1:60 1:150 curtain wall steel structure standard drawing幕墻鋼結構標準圖 A1 1:20 1:30 1:50 1:100 1:150 1:200 elevator steel structure standard drawing電梯鋼結構標準圖 A1 1:20 1:30 1:50 1:100 1:150 1:200 stairs steel structure s

19、tandard drawing樓梯鋼結構標準圖 A1 1:20 1:30 1:50 1:100 1:150 1:200 application, galvanizing standard drawing涂裝、鍍鋅標準圖 A1 1:20 1:30 1:50 1:100 1:150 1:200 detail詳圖 A1 1:5 1:10 1:30 1:50 A3 1:5 1:10 1:30 1:50 local detail局部詳圖 A1 1:2 1:5 1:10b.In principle, one paper type of project can but use uniform scale.項

20、目的一個圖紙類別原則上只能使用統一比例c.In principle, it can but dimension actual sizes in drawings. It may dimension actual numerical value only when unavoidable.圖紙內原則上只能標準實際尺寸，在非不得已情況下可標注實際數值。3.4 Font and Lineation字體以及線體a.Font variety is restricted in 12 type except sheet boundary.(number, English is Romans; Chinese

21、 is Song typeface or HZ1; aspect ratio of letter is 0.7)除圖框外,字體種類限制在12種之內(數字、英文Romans,中文宋體或HZ1,文字寬高比要設定為0.7)b.Define the height of letter as follows.字體高度按下表規定the height of letter字體高度(mm)Application適 用 對 象general drawing一般圖A1drawing name圖紙名3.5title of axis, size between axis, direction, lifting direc

22、tion軸線名、軸間尺寸、方向、吊裝方向3main dimension, member mark, common, special matters need attention, member list主要尺寸、構件號、共通事項、特別注意事項、構件清單2.5secondary dimension, various main dimension, local detail dimension次要尺寸、各種主要標注、局部詳圖標注detail詳圖A1member mark, main locating axis構件號、主定位軸線3main component and numbering of mai

23、n parts which connected to main component, node number, main dimension, section title, index dimension, direction, piece list title主部件以及與主部件連接的主要部件的編號、接點號、主要尺寸、斷面名稱、索引標注、方向、零件表名稱2.5secondary component dimension and size, various main dimension, common次要部件的注記以及尺寸、各種主要標注、共通事項 font not include in sheet

24、 boundary不含圖框內的字體 c.All thickness of lineation must be uniform, range from 0.1mm to 0.25mm.各種線的線粗必須統一,控制在0.1mm0.25mm之內d.The type of line usually takes the default of X-steel. Define the following specification only when drawing with CAD: heavy line for object border, 0.25mm for the typing line width

25、; fine dotted line for object dashed, 0.10mm for the typing line width; single dash dot line for object centerline, 0.15mm for the typing line width; fine line for dimension line, 0.13mm for the typing line width.線型一般均采用-steel默認線型及比例。若僅采用CAD制圖時,暫做以下規定：物體邊界采用粗實線，打印線寬0.25mm；物體虛線采用細虛線，打印線寬0.10mm；物體中心線采

26、用單點劃（細）線，打印線寬0.15mm；尺寸線采用細實線打印線寬0.13mm。e.fine line for outer sheet boundary,0.10mm for the typing line width; heavy line for inner sheet boundary, 0.35mm for the typing line width外圖框采用細實線，打印線寬0.10mm；內圖框采用粗實線，打印線寬0.35mmg.the height of text文本的高度:the annotations district: 3.0mm for title; 2.5mm for con

27、tent附注區：題頭3.0mm；內容2.5mm；the header area: 3.0mm for drawing number; 2.5mm for scale, version, date, etc; 2.0mm for the rest, 0.15mm for the typing line width; Letter should be clear when printing half.圖標區：圖號3.0mm；比例、版本、日期等信息2.5mm；其余2.0mm打印線寬應為0.15毫米；當圖紙縮半打印時，文字應清晰可見。h.General, apply small font to pie

28、ce mark assembled in shop, and apply big font to all texts.車間內裝配用的零件標號通常采用小字體，大寫字體通常用于所有文本。i.Member title with double underline spaces the first underline 1mm and spaces the second underline 2mm; 0.3mm for the first underline thickness, 0.13mm for the last.構件名稱必須帶雙下劃線，離第一條下劃線1mm；第一條下劃線粗0.3mm，第二條下劃線0

29、.13mm，二者間距1mm；j.Section must be with single heavy underline, 0.3mm for the thickness, 1mm for the clearance of word line.剖面必須帶單條粗下劃線，線粗0.3mm,字線間距1mm.3.5 Size Dimension尺寸標注a. Indicate altitude with meter and millimeter for other size. Do not show unit in drawings.除高程以米計以外其余尺寸以毫米記，圖中不標注單位。b. Provide a

30、rrow dimension at the end of size. Space at least 1mm between dimension line and dimensioning position.尺寸端部統一規定采用箭頭標注，尺寸線與標注部位至少預留1mm的間隙c. Dimension should be layered. The first layer is member locating point dimension, the second layer is member length and the third layer is locating of local detai

31、l on members, the fourth layer is dimensioning of local detail. Dimension line should avoid cross.尺寸要分層標注，第一層尺寸為構件定位點尺寸，第二層為構件長度，第三層為局部細節在構件上的定位，第四層為局部細節的尺寸標注。尺寸線應盡量避免交叉。d. Dimension in the same series should be aligned in line.同一系列的尺寸應整列對齊。e. In principle, the arrow at the end of dimension line is

32、1.5mm(general drawing) or 1.2mm (detail drawing).尺寸線端部的箭頭原則上為1.5mm(一般圖)或1.2mm(詳圖)f. Dimension Splice position and eccentricity size as follows:節點板位置以及偏心尺寸按下圖要領標注g. Dimension detail size as follows(n is greater than or equal to 3):細部尺寸按下列要領標注。(n要大于等于3)h. Azimuth and the direction of diagrammatic pres

33、entation方位以及圖示方向3.6 Drawing Number圖紙編號a. See building project drawing number system as follows. Drawing number consists of drawing title, category code name and serial number.建筑工程圖紙編號系統(見下表) 圖紙編號由圖紙名稱、種類代號加節號（一部分為層號）以及序號構成。Drawing Name圖紙名稱Drawing No.圖紙編號Remark備注Layout of bolt at toe柱底螺栓布置圖A+code num

34、ber+序號Detail is contained.含詳圖Plan平面圖F+floor mark+code number+樓層號+序號Layout of prepared hole and embedded parts is contained.含預留孔布置圖、預埋件布置圖Elevation立面圖E+truss name+code number+桁架名+序號桁架名參閱附圖Joint standard drawing節點標準圖TS+code numberTS+序號Weld standard drawing焊接標準圖坡口標準圖TWS+ code number TWS+序號lifting stand

35、ard drawing吊裝標準圖TKS+ code number TKS+序號elevator steel structure standard drawing電梯鋼結構標準圖TEV+機號+序號curtain wall steel structure standard drawing幕墻鋼結構標準圖TCW+floor mark+ code numberTCW+樓層號+序號ALC steel structure standard drawingALC鋼結構標準圖ALC+floor mark+ code numberALC+樓層號+序號stairs steel structure standard

36、 drawing樓梯鋼結構標準圖TKF+stairs name+ code numberTKF+樓梯名+序號application, galvanizing standard drawing涂裝、鍍鋅標準圖TPS+floor mark+ code numberTPS+樓層號+序號Detail of main truss column head or other column head主桁架柱頭以及其他柱頭詳圖section+C+ code number節+C+序號分類方法參閱附圖Detail of main truss inclined piece(vertical plane)主桁架斜桿（垂

37、直面）詳圖section+T+ code number節+T+序號Detail of main truss horizontal member主桁架水平桿件詳圖floor+G+code number樓層號+G+序號Detail of beam梁詳圖floor mark+B+ code number樓層號+B+序號All kinds of trabecula is contained.含各類小梁Detail of interlaminar column層間柱詳圖floor mark+P+ code number樓層號+P+序號樓層號以柱頭所在的樓層為準Detail of embedded par

38、ts預埋件詳圖floor mark+EMB+ code number樓層號+EMB+序號Detail of horizontal inclined piece水平小斜撐詳圖floor mark+H+ code number樓層號+H+序號Detail of vertical inclined piece垂直小斜撐詳圖floor mark+V+ code number樓層號+V+序號樓層號以柱頭所在的樓層為準Steel casting鑄鋼件N+steel casting mark+ code number N+鑄鋼件號+序號Stairs樓梯K+stairs mark+ code numberK+

39、樓梯號+序號b.Shop Drawing Numbering System橋梁工程圖紙編號系統（見下表）Prefix前綴Contents Description內容描述WDWelding Detail 焊接詳圖或標準圖WSWork Sheets(calculation and layouts used to prepare shop drawings; not to be reviewed as shop fabrication )工作表（用于準備加工圖的計算書和方案圖；不需要送審）TDTypical details and layouts(details and layouts to pre

40、pare shop drawings; not to be reviewed as shop fabrication drawings)典型詳圖和方案圖（用于準備加工圖的詳圖和方案，不需要送審）GNGeneral shop notes and typical details(lists appropriate notes for welding, paint, etc.) 車間制造的注解和典型詳圖（對焊接、涂裝等列舉一些適當?shù)淖⑨專〣GBasic girder diagrams ( Web and flange cutting diagrams)基本大梁圖（腹板和翼緣切割圖）WCWeb cam

41、ber details ( camber cutting and splicing of webs)腹板預拱度詳圖（預拱度切割位置和腹板拼接）FSFlange splicing details( assembly and splicing of flanges).翼緣板拼接詳圖（翼緣板裝配和拼接）。WC或BG圖應包含腹板至翼緣的焊接FWField work sheets ( used to obtain field dimensions and/or show required fieldwork, including field reaming and drilling) 現場工作表（用于標

42、示工地工作的相關尺寸和/或工地鉸孔和鉆孔等工作）HCHorizontal curve diagrams ( final line curve diagrams per piece with horizontal ordinates shown)水平曲線標注方法（標注每段曲線在水平線上的最終橫、縱坐標）XGirder job standards( parts details for I girders, box girders and tub girders)主梁零件標準圖（工字梁、箱梁和槽式梁的零件詳圖）ZStringer job standards縱梁零件標準圖MMiscellaneous

43、job standards(parts details, rolled beams, cross frames, diaphragms, etc.) 雜項零件標準圖（零件詳圖、軋制小梁、橫梁結構、橫隔板等）SB or SDSub-assemblies(Parts, shop or field assembled, as units prior to incorporating into a shipping piece or the structure)組件（將多個零件在工廠或現場拼裝成的船運部件或結構件）EAnchor bolt plans, field bolt and erection

44、framing plans (location of shipping piece marks). Note: these are not erection procedure plans.錨固螺栓平面布置圖，現場安裝螺栓平面圖和結構安裝圖（帶標記的船運部件位置），說明：這些不是安裝工藝圖SAShop assembly diagrams(line assembly reaming, unit assembly, etc.工廠拼裝圖（畫出裝配的鉸孔，裝配的組件等）1 thruDetails of girders, cross frames, stringers, diaphragms, etc.

45、 梁，橫梁結構，縱梁，橫隔板等的詳圖SPShipping procedures(detailed procedure to ship unique pieces)船運工藝（特殊構件的詳細船運工藝）WPWelding procedures( used to show required welding procedures; to be submitted and approved separately from shop detail drawings)焊接工藝（用來明確焊接工藝的要求；應分別根據車間詳圖提交審核）Note: Prefix typically followed by numeri

46、cal identification 1,2,3,etc.注釋：前綴通常是通過數值諸如1，2，3來確定。Shop Detail Drawing Numbering Sequence橋梁工程加工圖編號順序There should be a logical sequence in shop detail drawings that will aid the reviewer and shop personnel. The approval review process will be expedited if all structure drawings are organized in a co

47、mmon sequence. The prefixed drawings should be located within sets in the order shown in shop drawing numbering system.加工圖應遵循邏輯的編號順序，以便為審圖者和生產人員服務。如果所有的結構圖按常用的順序整理完整，審圖過程就可以加快。圖紙的前綴應根據前面的圖紙編號系統里的相關條目進行設置。Numbered drawings should be sequenced similarly to the following example:已編號的圖紙順序應和下表類似：Descript

48、ion描述Drawing No. 圖號Bearing Detail支座詳圖1Girders梁 2G1A2AC，2BC，2C*3G2A34G3A45G4A56G1B67G2B78G3B89G4B9Cross Frames, Diaphragms&other Misc.橫梁結構，橫隔板以及其它雜項103.7 Marking System for Shipping Pieces橋梁工程構件編號系統Identifier名稱Description描述GGirder大梁（用于翼緣、腹板的構件）BGBox Girder鋼箱梁（封閉的箱形構件）TGTub Girder平梁（敞開的箱形構件）SStrin

49、ger縱梁（型鋼構件）DDiaphragm橫隔板（介于主要構件或板塊間的單個滾壓形式）CF，K，XCross Frame剪刀撐（介于主要構件之間的組合構件，這些構件主要為寬翼緣截面，角鋼等）L or LBLateral Bracing橫向支撐（所有水平面，對角支撐）MSMiscellaneous雜項（無法歸類的船運散件）DUDeck Units橋面單元（通常指鐵路橋上附帶鋼板的平面梁）ABAnchor Bolt錨固螺栓BPBronze Plate銅板BRBrackets牛腿（懸臂形式）EBElastomeric Bearing彈性支座FB or BFloor Beams平面梁（扎制型鋼或焊接工

50、字梁）PPPreformed Pad預制墊LPLeveling Plate水平測量用鋼板MPMasonry Plate砌筑板PPin銷RPRocker Plate平衡板SPSole Plate基礎板WWasher墊圈WDWeld Detail Drawing焊接詳圖（用在有許多焊接詳圖的復雜結構）Fracture critical pieces may be prefixed F, such as FG, FBG, FTG, etc. This is optional and may be used by a Fabricator to differentiate this material.

51、 The above letters may be prefixed with the sheet number on which the piece is detailed, serving as a self-indexing system, and suffixed with a numerical identification. Longitudinal main members shall be suffixed A, B, C, etc. in addition to their numerical suffix.臨界脆斷構件可以加前綴“F”，諸如FG，F(xiàn)BG，F(xiàn)TG等等。這是可選

52、擇的，可以由制造商自己采用以辨別這種材料。以上字母可以根據圖表編號加前綴，也能根據數值的辨別加后綴?？v向的主構件，除了它們的數值后綴外，還可以加后綴A，B，C等。*Use letters as suffix when details require more than one drawing.*當詳圖需要不止一張時，用字母作為后綴。Note: Certain projects may require deviation from the Shop Detail Drawing Numbering System Sequence, dependent upon the Fabricators r

53、equirements. Also, WS, TD, GN, WC&FS drawings may be prepared and submitted with other necessary sheets/information (E&WP) prior to balance of detail drawings on large projects in order to begin with fabrication of these pieces. Partial submittals must be complete enough to allow checkers to

54、 adequately cross-reference information and avoid requiring later re-checking.注釋：具體項目也可能根據制造商的需要進行調整使加工圖編號系統，這樣順序有可能產生偏差。同時，在一些大的項目中，為了在一開始就方便零件的裝配，要先準備和提交WS，TD，GN，WC和FS圖紙 連同其它必要的圖紙/信息（E和WP），目的是及時完成以上圖表以便讓復核人員能充分地相互對照，避免事后再次檢查。3.8 Building Project Member Numbering System建筑工程構件編號系統Number member accor

55、ding to follow principle, the category code name of member is the same to drawing numbering.構件根據以下原則編號，構件的種類代號采用與圖紙編號相同的種類代號。）main column主要柱 section number+C+elevation number+serial number節號+C+立面號+序號）main horizontal member of truss主要桁架水平桿件section number+G+elevation number+serial number節號+G+立面號+序號）ma

56、in horizontal member of truss主桁架水平桿件floor number+G+elevation number+serial number樓層號+G+立面號+序號4）beam, interlaminar beam梁、層間梁 floor number+B+design mark+serial number樓層號+B+設計記號+序號 M+floor number+B+design mark+serial number M+樓層號+B+設計記號+序號5）interlaminar column層間柱floor number+P+design mark+serial number樓層號+P+設計號+序號6）horizontal inclined brace水平小斜撐 floor number+H+design mark+serial number樓層號+H+設計號+序號7）vertical inclined brace垂直小斜撐 floor number+V+desi