【國(guó)際標(biāo)準(zhǔn)】ASME B16.14-1991 鋼鐵制管螺塞、襯套和防松螺母.pdf

1、COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services 0759670 0081832 bH I AN AMERICAN NATIONAL STANDARD Ferrous Pipe Plugs, Bushings, and Locknuts with Pipe Threads AS

2、ME B16.14-1991 (REVISION OF ANSI B16.14-1983) The American Society of Mechanical Engineers 345 East 47th Street, New York, N.Y. 10017 - COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of Mechanical Engineers Licensed by Informat

3、ion Handling Services Date of Issuance: February 15, 1991 The 1991 edition of this Standard is being issued with an automatic addenda subscription service. The use of an addenda allows revisions made in re- sponse to public review comments or committee actions to be published as necessary; revisions

4、 published in addenda will become effective 6 months after the Date of Issuance of the addenda. The next edition of this Standard is scheduled for publication in 1996. ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. The interpretations will

5、be included with the above addenda service. Interpretations are not part of the addenda to the standard. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Sta

6、ndards. The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment which provides an opportunity for a

7、dditional public input from industry, academia, regulatory agencies, and the public-at-large. ASME does not approve, rate, or endorse any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with

8、 any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable Letters Patent, nor assume any such liability. Users of a code or standard are expressly advised that determination of the validity of any such pat

9、ent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility

10、for only those interpretations issued in accordance with governing ASME procedures and policies which preclude the issuance of interpretations by individual vol- unteers. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written

11、 permission of the publisher. Copyright Q 1991 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A. L COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of Mechanical Engineers Licensed by Informati

12、on Handling Services ASME BLb.14 91 I 0757670 0041834 T e FOREWORD (This Foreword i s not part of ASME B16.14-1991.) In 1921, the American Engineering Standards Committee later the American Standards Association (ASA) organized Sectional Committee B16 to unify and develop standards for pipe flanges

13、and fittings. Cosponsors of the B16 Committee were the American Society of Mechanical Engineers (ASME), the Heating and Piping Contractors National Association now Mechanical Contractors Association of America (MCAA), and the Manufacturers Standardization Society of the Valve and Fitting Industry (M

14、SS). Cosponsors were later designated as Co-Secretariat organizations. Threaded fittings were also included in the scope of the B16 Committee .and Subcommittee 2 (now Subcommittee B) was made responsible for threaded fittings other than steel. The American Standard for Pipe Plugs was originally publ

15、ished as ASA B16e2-1936. It had been developed by Subcommittee 2 from material assembled and published by MSS as a standard practice in April, 1929. From the beginning, pipe plugs have been made with the American Standard Taper Pipe Thread but the design of the square heads necessary to screw them i

16、nto fittings or any taped hole has been a matter of manufacturers and users individual design. However, the use of pipe plugs soon broadened and they came to be employed in many other service applications, e.g., automotive and industrial machinery. Accordingly, it was natural for the dimensions of t

17、he square heads and the sockets to conform to standard open wrench sizes and to maximum dimensions of standard hot rolled steel bars. Pipe bushing and locknut dimensions were originally included in ASA B16c-1939, American Standard for 150 lb Malleable Iron Screwed Fittings. B16c-1939 was adapted fro

18、m information assembled and published by MSS in 1929. In response to a demand for inclusion under one cover, B16.14-1943, American Standard for Ferrous Plugs, Bushings, Locknuts, and Caps, was developed from ASA B16c-1939 and ASA B16d-1941, the American Standard for Cast Iron Screwed Fittings, 125 l

19、b and 250 lb, and approved by ASA in October 1943. The section of B16.14 covering pipe caps was later removed because of differences in pressure ratings between caps made of cast iron and malleable iron. This Standard was revised in 1948 and was approved by letter ballot vote of the Sectional Commit

20、tee and, following the approval of the sponsor bodies, it was presented to ASA, now the American National Standards Institute, Inc. (ANSI), with recommendations for approval as an American Standard. This approval and designation was given on April 6, 1949. Subcommittee 2 began a review of the docume

21、nt in 1963 and completed its work in 1964. The Sectional Committee approved a number of minor changes in format and wording. Following approval by the sponsor organizations, ANSI approval was granted on November 12, 1965. In 1970, a review was initiated by Subcommittee 2, which resulted in the propo

22、sal to revise the document in several minor areas as well as up-dating referenced standards. Following approvals by the Standards Committee and Co-Secretariat, ANSI granted iii COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of

23、Mechanical Engineers Licensed by Information Handling Services ASME c1759670 088L835 approval on November 1, 1971. In 1975, review was again initiated by Subcommittee B (formerly 2) and it was determined that the only significant changes needed were up-dating of referenced standards and the addition

24、 of metric equivalents. Approvals were granted by the Standards Committee, Co-Secretariat and ANSI, the latter on February 4, 1977. In 1982, the American National Standards Committee was reorganized as an ASME Committee operating under procedures accredited by ANSI. That same year, Subcommittee B on

25、ce again began review of the Standard. The only changes made were the dates of the referenced standards. After approval by the Standards Committee and the ASME, final approval was granted by ANSI in July 1983. This revision of B16.14 establishes U.S. customary units as the Standard, updates the refe

26、renced standards, and specifies minimum specifications for steel fittings. Following approval by the Standards Committee and ASME, approval as an American National Standard was given by ANSI on January 4, 1991, with the new designation ASME B16.14- 1991. This Standard is issued on a subscription ser

27、vice addenda basis. The use of an addenda system allows revisions made in response to public review comments or committee actions to be published on a regular biannual basis. Revisions published by addenda become effective one year after the Date of Issuance. ASME issues written replies to inquiries

28、 concerning interpretation of technical aspects of this Standard. With the 1983 Edition, interpretations will be included with the addenda service. Interpretations are not part of the addenda to the Standard. All requests for interpretations or suggestions for revisions should be sent to: Secretary,

29、 B16, The American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017. COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services ASME B l b - 1 4 91

30、H 0759b70 0083836 3 I ASME B16 COMMITTEE Standardization of Valves, Flanges, Fittings, Gaskets and Valve Actuators (The following is the roster of the Committee at the time of approval of this Standard.) OFFICERS W. N. McLean, Chairman R. A. Schmidt, Vice Chairman P. D. Stumpf, Secretary COMMITTEE P

31、ERSONNEL W. L. Ballis, Columbia Gas Distribution Co., Columbus, Ohio J. E. Batey, Union Carbide Corp., South Charleston, West Virginia K. M. Bell, Underwriters Laboratories Inc., Northbrook, Illinois R. R. Brodin, Fisher Controls International Inc., Marshalltown, Iowa W. G. Canham, Jr., Brentwood, M

32、issouri A. Cohen, Copper Development Association, Greenwich, Connecticut W. C. Farrell, Jr., Stockham Valves and Fittings Inc., Birmingham, Alabama D. R. Frikken, Monsanto Co., St. Louis, Missouri M. W. Garland, Frick Co., Waynesboro, Pennsylvania J. C. Inch, Mueller Brass Co., Hartsville, Tennessee

33、 J. S. John, Houston, Texas W. G. Knecht, AnchorlDarling Valve Co., Williamsport, Pennsylvania R. Koester, The William Powell Co., Cincinnati, Ohio J. H. Longacre, Nibco Inc., Elkhart, Indiana J. H. McCauley, Jr., McCauley Mechanical, Chicago, Illinois W. N. McLean, Chairman, Newco Valves, Palos Par

34、k, Illinois M. E. OHagan, Valve Manufacturers Association, Washington, D.C. A. F. Rhodes, Gripper Inc., Houston, Texas R. A. Schmidt, Vice Chairman, Ladish Co., Russellville, Arkansas T. F. Stroud, Ductile Iron Pipe Research Association, Birmingham, Alabama P. D. Stumpf, Secretary, ASME, New York, N

35、ew York R. E. White, Repairs Inc., South Bend, Indiana D. A. Williams, Southern Company Services, Birmingham, Alabama D. Wilson, Mobile Pipeline Co., Dallas, Texas PERSONNEL OF SUBCOMMITTEE B - THREADED FITTINGS (EXCEPT STEEL) W. C. Farrell. Jr. Chairman, Stockham Valves and Fittings Inc., Birmingha

36、m, Alabama J. P. Millman, Secretary, ASME, New York, New York A. Cohen, Copper Development Association, Greenwich, Connecticut M. D. Goodson, U-Brand Corp., Ashland, Ohio J. H. Longacre, Nibco Inc., Elkhart, Indiana G. J. Lyman, Ward Manufacturing, Inc., Blossburg, Pennsylvania V COPYRIGHT American

37、Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services CONTENTS . Foreword . 111 Standards Committee Roster . v Scope . 1 Pressure-Temperature Ratings . 1 Size . 1 Materials . 1 Dimensions

38、 and Tolerances . 1 Threading . 1 PatternTaper . 2 Marking . 1 Tables 1 Dimensions of Square Head Plugs . 3 2 Dimensions of Bar or Slotted Head Plugs . 4 3 Dimensions of Countersunk Plugs . 4 4 Dimensions of Outside Head. Inside Head. and Face Bushings . 5 5 DimensionsofLocknuts . 7 Annex A Referenc

39、es . 9 vii COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services ASME 816.14-1991 FERROUS PIPE PLUGS, BUSHINGS, AND LOCKNUTS WITH PIPE THREADS 1 SCOPE This Standard for

40、 Ferrous Pipe Plugs, Bushings, and Locknuts with Pipe Threads covers: (a) pressure-temperature ratings; (b) size; (c) marking; (d) materials; (e) dimensions and tolerances; (f) threading; and (g) pattern taper. 2 PRESSURE-TEMPERATURE RATINGS (a) Pressure-temperature ratings for plugs and bush- ings

41、shall be in accordance with ANSUASME B16.4 if made of cast iron, or ANSUASME B16.3 if made of malleable iron, ductile iron or steel. Use of cored plugs and hexagon head bushings should be limited to Class 125 cast iron and Class 150 malleable iron threaded fit- tings. Solid plugs and face bushings a

42、re recommended for use with Class 250 cast iron fittings and Class 300 malleable iron fittings. (b) Locknuts are not pressure-temperature rated. 3 SIZE The size of the fittings scheduled in the following ta- d) bles is identified by the corresponding nominal pipe size. 4 MARKING Each fitting shall b

43、e marked for identification with the manufacturers name or trademark, except where a marking is impractical. The use of the word nominal as a modifier of a dimension or size is intended to indicate that the stated dimension or size is used for pur- poses of designation. . 5 MATERIALS (a) These fitti

44、ngs are furnished in cast iron, mallea- ble iron, ductile iron, or steel as indicated in the indi- vidual tables. (b) The chemical and mechanical properties of cast material shall equal or exceed those properties listed in ASTM A126, Specification for Gray Iron Castings for Valves, Flanges, and Pipe

45、 Fittings, ASTM A197, Spec- ification for Cupola Malleable Iron, and ASTM A395, Specification for Ferritic Ductile Iron Pressure Retain- ing Castings for Use at Elevated Temperatures, as ap- plicable. Steel castings, forgings, or machined bar properties shall correspond to the comparable ASTM castin

46、g material specifications. The fittings manufac- turer shall be prepared to certify conformance based on test data. 6 DIMENSIONS AND TOLERANCES (a) Dimensions in U.S. Customary Units are used in this standard. (b) At no point in the component wall shall the metal thickness be less than 90% of the va

47、lues listed in the tables. 7 THREADS 7.1 Thread Form Threads shall be in accordance with ANSVASME B1.20.1. All internal taper pipe threads shall be coun- tersunk a distance not less than one half the pitch of the thread at an angle of approximately 45 deg. with the axis of the thread. External taper

48、 pipe threads shall be chamfered at an angle between 30 and 45 deg. with the axis. Countersinking and chamfering shall be concentric with the threads. (a) The length of threads specified in all tables shall be measured to include the countersink or chamfer. (b) The maximum allowable variation in the

49、 align- ment of threads of all openings shall be 0.06 in./ft. 1 COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services ASME 616.14-1991 7.2 Plugs Plugs shall be threaded

50、 with ANSUASME B1.20.1 taper pipe threads. The variation in threading shall be limited to one turn large or one turn small from the gag- ing notch on plug or gaging face of ring when using working gages. 7.3 Bushings Bushings shall be threaded with American National Standard taper pipe threads. Gagi

51、ng of all threads shall comply with ANSUASME B1.20.1, except those sizes of outside hexagon bushings where the external thread lengths are shorter than required by ANSUASME B1.20.1. These bushings should be threaded so that when malung up the joint, the shoulder of the head will not interfere. To in

52、sure this, the threads. when made to the minimum length, shall be gaged as listed below with a tolerance of one turn large or small. NPS to l%, incl. 1 turn large NPS 2 1% turns large NPS 2% to 8, incl. 2 turns large FERROUS PIPE PLUGS, BUSHINGS, AND LOCKNUTS WITH PIPE THREADS ( a ) .4n outside head

53、 bushing is one having any part of the polygon protruding beyond the outside diameter of the large end of the external thread. (b) An inside head bushing is one having all parts of the polygon head contained Lvithin the root diameter of the large end of the external thread. (c) A face bushing is one

54、 having two lugs on the face of the large end of the external thread by which a bar can be used for make-up Lvith internal pipe threads. Lugs are optional on face bushings in small pipe sizes when made of bar stock. 7.4 Locknuts Locknuts shall be tapped u.ith straight pipe threads in accordance Lvit

55、h ANS1;ASME B1 .?-O. l . 8 PATTERN TAPER Plug squares or hexagons. raised or countersunk, may have opposite sides tapered a maximum of 4 deg. total. 3 L COPYRIGHT American Society of Mechanical Engineers Licensed by Information Handling Services COPYRIGHT American Society of Mechanical Engineers Lic

56、ensed by Information Handling Services ASME Bbb-34 91 I 0759670 O083840 5 M FERROUS PIPE PLUGS, BUSHINGS, AND LOCKNUTS WITH PIPE THREADS ASME 616.14-1991 PLUGS I Solid Plugs Cored Plugs TABLE 1 DIMENSIONS OF SQUARE HEAD PLUGS Nominal Length, Pipe Size Thread Notes (1 ), ( 2 1 1 Min. A 0.37 0.44 0.48

57、 0.56 0.63 0.75 0.80 0.83 0.88 1 .O7 1.13 1.18 ieight of Square, Min. B 0.24 0.28 0.31 0.38 0.44 - 0.50 0.56 0.62 0.68 0.74 0.80 0.86 Nominal Width 4cross Flats Note (311 C 132 3h Il 6 11 6 T6 6 6 1 1% 1 5/16 1 v 2 1 % S 1 7 % Nominal Metal rhickness Note (411 G 0.16 0 . 1 8 0.20 0.22 0.24 0.26 0.29 0.31 0.34 . GENERAL