石油-站場英語

1、Station-yard English站場英語1. Hello, can you read me?能聽見我說話嗎？2. Yes, I read you clearly.能聽清楚。3. Its not clear.不很清楚。4. Hello, this is ps#1, may I increase (decrease) discharge pressure?你好，這是1號站，可以提高（降低）出站壓力嗎？5. Hello, this is HS#2, may I increase (decrease) suction pressure?你好，這是2號加熱站，我可以提高（降低）進站壓力嗎？6.

2、Hello, this is ps#3, I have already fully opened (closed) MOV10001.你好，這是3號站，我已經全開（全關）MOV10001.7. Hello, this is ps#4, can I start (stop) screw pump now?你好,這是4號站,我現在可以啟(關)螺桿泵嗎?8. I will go outside to check (record) parameter reading.我要出去檢查(記錄)參數值。9. Hello, this is MCC, please launch (receive) a pig a

3、t 8:00am tomorrow morning.你好,這是中心控制室,請?jiān)诿魈煸绯?點發（收）球。10. Hello, this is MCC, please shutdown your station normally (emergency).你好,這是中心控制室,請正常(緊急)關斷你們站。11. Hello, this is terminal station, I found some heavy oil leakage in inlet pipeline, we have to shutdown our station to repair it.你好,這是末站,我發現進站管線嚴重漏油

4、,我們需要停止站場運行,進行維修。12. Please make word order to electric engineer to check isolation transformer.請給電氣工程師開工作票,檢查隔離變壓器。13. Please make word order to mechanic engineer to check water pump.請給機械工程師開工作票,檢查水泵。14. Our station is running smoothly.我們站運行平穩。15. Hello, this is MCC, please start your station now.你

5、好,這是中心控制室,請現在啟動你們站。16. Hello, this is MCC, please increase (reduce) the flow to maximum (minimum).你好,這是中心控制室,請把流量提高(降低)到最大值(最小值)。17. There are some problems on flow-computer, may you check it?流量計算機有問題,你能去檢查一下嗎?18. How many available pigs are there in your station?你們站有多少可用清管球?19. How many pig skelect

6、ons in your station?你們站有多少發球架？20. Do you have spare pigs?你們有備用球嗎?21. What is the distance between initial station and terminal station?首站和末站之間有多遠?22. Wheres your location?你在什么位置?23. I am in the control room.我在控制室。24. Hello, this is MCC, please send the daily report to me.你好,這是中心控制室,請把日?qǐng)?bào)表送給我。25. I ha

7、ve just sent it to you by email, please check it.我用email將它發送給你了,請檢查。26. Please write it down on the daily log-book.請把它記在每日工作記錄上。27. Please make phone call to MCC and tell the details about the situation here.請打電話給中心控制室,將這的狀態細節告訴他們。28. We will have a meeting this evening to discuss the next operation

8、 plan.我們今晚要開會討論下一步操作計劃。29. The discharge pressure is too high, please reduce the pump speed. (rpm-revolutions per minute. 轉速)出站壓力太高,請降低泵的轉速。30. How much is the flow rate now?現在流速是多少?31. The flow rate is 100 cubic meters per hour (100m3/h).流速是100m3/h。32. Please tell me the total volume.請告訴我總數。33. Ple

9、ase report the gross volume.請匯報總值。34. Please record the net volume.請記錄凈值。35. Please send the hourly report to MCC at once.請立即將每小時記錄送到MCC。36. The MOV10001 is working abnormally, please send work order to electric & mechanic engineer to check it.MOV10001閥門工作不正常,請給機械和電氣工程師開工作票檢查此閥門。37. Who is on duty n

10、ow?現在誰值班?38. Day shift operator is on duty instead of night shift operator.白班正在替換夜班。39. Today we will have a shift between day shift and night shift.今天我們將上一個白班或夜班。40. Please send a driver to kitchen.請派一個司機到廚房來。41. Please switch on (off) the light.請開(關)燈。42. Please supply the power to frequency conve

11、rter.請給變頻器送電。43. There is an abnormal differential pressure on filter101, please change it to filter102.101過濾器差壓不正常,請切換到102過濾器。44. Please fill lubricant cream into this valve.請給閥門加注潤滑脂。45. Please fill seal grease into this valve.請給閥門加注密封脂。46. Its time for lunch.現在是午飯時間。47. What time are we usually o

12、n duty everyday?我們每天什么時間上班?48. Please keep the hotline standby, its just for connecting with MCC while having something import to report.請保持熱線備用,這是為有重要事情同MCC聯系準備的。49. Please keep the car standby, we will carry a pig tomorrow.請保持車輛備用,我們明天要運球。50. Please first open the vent valve.請先開放空閥。51. Please open

13、 that valve to drain sump oil.請開那個閥門排放污油。52. The level of the sump tank is high, please start sump pump to reduce it.污油罐液位太高,請開污油泵降低液位。53. The level of the open sump tank is very low, no need to start sump pump.開著的污油罐液位很低,不需啟泵。54. The SCADA system had some problems, we cannt see other station.SCADA系

14、統有問題,我們看不到其他站。55. The station control system is not available, please control it by hand.站控系統（SCS）不能使用,請手動操作。56. May you tell me how to operate this equipment?你能告訴我怎樣使用這臺設備嗎?57. The flow rate decreased suddenly, maybe somewhere in upstream or downstream pipeline blocked.流速突然降低,可能是上下游某處管線破裂。58. The f

15、low rate is increasing very quickly, maybe somewhere in downstream pipeline was broken or exploded.流速增加很快,可能是下游管線某處破裂或爆管。59. Please record the data of cathodic protection volt. (ampere)請記錄陰保電壓數據。60. Please change a new amperite for this light.請給此燈換一個鎮流器。61. Please do it according to HSE.請根據HSE工作。62.

16、 Please obey operating procedures when you receive the pig.請?jiān)谑涨驎r(shí)遵守操作規程。63. Please carry out rules strictly and prevent from fire.請嚴格執行規定避免火災。64. Can you show me how to use this fire extinguisher?你能向我演示如何使用這個滅火器嗎?65. Which block valve acts as off-take valve station?哪個截?cái)嚅y作為分輸閥站?66. Main line strainer

17、should be switched due to differential pressure reached above 50kpa.當差壓達到50kpa時需切換主干線過濾器。67. Please contact with Zinder refinery. 請聯系津德爾煉廠。68. The screw pump tripped due to power failure.螺桿泵由于斷電而跳閘。69. Please confirm whether the pig receiver is online or not.請確認收球筒是否在線。70. Please tell me how many ca

18、thodic protection stations along the pipeline?請告訴我管線有多少陰保站。71. May you tell me how much crude temperature and viscosity are on the station inlet side.你能告訴我進站原油溫度和粘度嗎?72. The reading of pressure (temperature) transmitter10001 has something wrong, please check it.壓力(溫度)傳感器10001讀數有問題,請去檢查一下。73. Pressur

19、e relief valve10001 is working well or not?壓力泄放閥10001工作正常嗎?74. Check valve10001 cant prevent oil backflow, please check it.10001單向閥不能阻止原油回流,請檢查一下。75. Please close isolation valve10001.請關閉10001隔離閥。76. Please open stopple valve10001請打開10001旋塞閥。77. Please fill out piging report after pigging operation.

20、請?jiān)谑瞻l(fā)球結束后填寫收發球記錄。78. Can you tell me what the purpose of the VFD is?你能告訴我VFD的目標嗎?79. Its to increase or decrease the speed of rotation of the stators electromagnetic field by increasing or decreasing the frequency of the AC power going to stator.通過提高或降低定子的交流電頻率來提高或降低勵磁線圈的轉速。80. Whats the main purpose

21、 of water injection into the pipeline during the commissioning ?在試運期間向管線內注水的主要目的是什么?81. Its for establishment of backpressure and hydrostatic test.是為了建立背壓和液壓試驗。82. What alarm?什么報警?83. Pump suction pressure is low-low.泵吸入壓力低低。84. Discharge pressure is high-high.排出壓力高高。85. Please set a set-point for t

22、his pressure relief valve.請給壓力泄放閥設置一個設定值。86. What reason caused the pump to trip out?什么原因引起泵跳車?87. I am not sure, lets check historic trend chart.我不確定,讓我們察看一下歷史趨勢圖吧。88. The pipeline is not stable, please monitor suction pressure.管線工作不穩定,請監視吸入壓力。89. Dont forget to take safe measures when you go down

23、to sump tank.下污油罐時請不要忘記佩戴安全防護設施。90. When you turn off the power, please execute it on the order當關斷電源時,請按規程操作。91. How often usually does your station make tour-inspection of the instrument automation equipment?你們站多長時間巡檢一次自動化儀表設備?92. We do it twice a day.我們每天巡檢兩次。93. It is time to make calibration and

24、 examination of instrument, we should prepare for it in advance.儀器到期校正和測試了,我們應提前準備好。94. Please dont change the automation system at will if without the approval of the department concerned.未經有關部門批準不得改變自動系統。95. Where is supervisor?監理在哪?96. He went to the site with vendor.他和廠家去現場了。97. Please check the

25、 oil level of the gear casing of pumps請檢查泵齒輪箱油位。98. Please carry out 800 operation hours maintenance for roller bearing driver-side.請對驅動端滾動軸承進行”運行800小時”后的維護保養。99. Please change the radios channel to channel number 2.請將無線電頻道換到2頻道。100. Please take the mobile radio with you when going outside to check.

26、請外出檢查時帶上移動電臺。101. Start up the waste oil pump.啟動污油泵。102. Stop the waste oil pump.停止污油泵。103. Start up the transferring pump.啟動輸油泵。104. Stop the transferring pump.停止輸油泵。105. Emergency shut down the pump.緊急停泵。106. Check the level of the waste oil tank.檢查污油罐的液位。107. Check the level of the relief tank.檢查

27、污油罐的液位。108. Emergency shut down the ESD valve.緊急關斷ESD閥門。109. Open the valve.打開閥門。 110. Close the valve.關閉閥門。 111. Pay attention to the inlet & outlet pressure and temperature when you patrol inspect.當你巡檢時，請注意進口和出口壓力和溫度。112. I have checked the high & low voltage switchgear, the data are normal.我已經檢查了

28、高低壓開關柜，是正常的。113. I have checked and reported the value of the turbo-flow meter.我已經檢查并報告了渦輪流量計的數值。114. We will receive the pig at 10:00am this morning, please prepare the pig receiver.我們將在今天上午10:00收球，請準備好收球筒。115. Please check data against alarm limits.請根據報警極限核對數據。116. Please vent the air from the pig

29、 receiver firstly when using it.在使用收球筒前請首先要放空。117. The pig receiver is online now.收球筒已導通流程。118. The pig indicator shows that the pig is arriving, may we take it out now?通球指示儀顯示球已到達，現在我們把它取出來嗎？119. I am sure the pig indicators are in reliable condition.我相信通球指示儀處于可靠的狀態中。120. The waste oil pressure in

30、the pig receiver has been relieved, and the pressure gauge shows the pressure is as the same as the atmospheric pressure, can we open the quick-opening closure now?收球筒污油已泄壓，壓力表顯示的壓力為與大氣壓相同，我們現在可以打開快開盲板嗎？121. Yes, you must operate it obeying the rule.是的，你必須遵守操作規程。122. Please release the pressure and

31、drain the oil in pig receiver immediately after receiving pig.收到球后，請立即打開放空和排污管線。123. Please vent the air in the pipe.請打開放空管線。124. I have vented the air, and the pressure is normal now.我已排出空氣，壓力是正常的了。125. The telephone has some problems, and the sound is not very clear, write order to the electrical

32、engineer to check it please. 電話有一些問題，聲音不是很清楚，請給電氣工程師寫操作票，檢查一下。129. Contact with the CPF to provide sufficient water supply.請與CPF聯系，提供足夠的水供應。130. Contact with the CPF, make sure CPF provides continuous power supply during commissioning period, especially ensuring the main pump units running continuou

33、sly for 24 hours.請與CPF聯系，確保CPF在投產期間的連續電力供應，特別是保障主泵機組運行24小時不間斷連續供電。131. Inspect the intelligent sensor such as the pressure transmitter, and check it with manual state.檢查智能傳感器如壓力變送器，檢查手動狀態。132. Check the display on the panel of the turbo-flow meter.檢查渦輪流量計顯示器。134. Emergency stop Unit A/B/C/D.緊急停止設備A

34、/ B/ C / D。135. Increase/decrease speed to 1000.提高/降低速度到1000rpm。136. Speed up/down to 650.加速/降速到650。138. Adjust the deviation of cylinder No.1.調整一號氣缸偏差。142. Reset the engine.復位發動機。143. Diesel flushing Unit.柴油沖洗裝置。144. Fully open the suction manual valve.全開吸入口手動閥門。145. Start pump sealing & lub oil fa

35、ns.啟動泵密封和滑油風扇。146. Check the engine vibration sensor.檢查發動機的振動傳感器。147. Check the charge air shut off valve position.檢查壓縮空氣切斷閥的位置。148. Monitor suction pressure.監控入口壓力。149. Partly open suction manual valve.半開入口手動閥。151. Change discharge valve to remote/local改變出口閥到遠程/本地。152. Carry out the pre-check.進行預檢查

36、。153. Check the sump oil level.檢查污油液位。154. Check the main pump casing temperature.檢查主泵殼溫度。155. Check the lubricate oil pump pressure.檢查滑油泵壓力。156. Check the diesel fuel pressure.檢查柴油機燃油壓力。159. Check the starting air pressure.檢查起動空氣壓力。160. Check the crude fuel temperature.檢查原油燃油溫度。161. Check the charg

37、e air pressure.檢查壓縮空氣壓力。162. Check the turbo charger inlet temperature.檢查渦輪增壓器入口溫度。163. Check the turbo charge outlet temperature.檢查渦輪增壓出口溫度。165. Check the lube oil temperature of engine.檢查發動機滑油溫度。166. Check the lube oil inlet pressure.檢查滑油進口壓力。167. Check the lube oil temperature before cooler.檢查的滑油

38、冷卻器前的潤滑油溫度。168. Check suction filter of diesel pump.檢查柴油泵入口過濾器。169. Check the lube oil differential pressure.檢查潤滑油差壓。170. Check the lube oil temperature.檢查滑油溫度。171. Change the lube oil filter from A to B.滑油過濾器由A切換到B。172. Change diesel fuel filter from A to B.柴油濾清器由A切換到B。173. Check pump DE seal loop

39、pressure. (DE: drive end)檢查泵驅動端密封圈的壓力。174. Check pump NDE seal loop pressure. (NDE: none drive end)檢查泵非驅動端密封圈的壓力。175. Check temp. of jacket water before engine.檢查發動機前的水套溫度。176. Check temp. of jacket water after engine.檢查發動機后的水套溫度。177. Check second water temp before lube oil cooler.檢查滑油冷卻器前的二次供水溫度。17

40、8. Check second water temp. after lub oil cooler 檢查滑油冷卻器后的二次水溫度。179. Check the jacket water pressure.檢查水套壓力。180. Check the second water pressure.檢查二次供水的壓力。181. Check the gearbox lube oil supply pressure.檢查變速箱滑油供給壓力。182. Check the gearbox lube oil supply temp.檢查變速箱滑油供應溫度。183. Check the gearbox lube o

41、il pump discharge pressure.檢查變速箱滑油泵的出口壓力。184. Check the gearbox lube oil supply pump temp.檢查變速箱滑油供給泵溫度。187. Check the gearbox outlet NDE journal brg. Temp. （brg.-bearing）檢查變速箱出口徑向非驅動端軸承溫度。188. Check the gearbox outlet DE journal brg. Temp.檢查變速箱出口徑向驅動端軸承溫度。189. Check pump DE journal brg. Temp.檢查泵徑向驅動

42、端軸承溫度。190. Check pump NDE journal brg. Temp.檢查泵徑向非驅動端軸承溫度。191. Check pump NDE inlet thrust brg. Temp.檢查泵進口非驅動端 推力軸承溫度。192. Check pump NDE outlet thrust brg. Temp.檢查泵出口 非驅動端 徑向軸承的溫度。194. Drain the fuel tank oil of Unit A.排放設備A的燃料油罐內的油。195. Check the gearbox lub oil level.檢查變速箱潤滑油液位。196. Check the sea

43、l oil reservoir level.檢查密封油箱液位。197. Check the Haske pump status.檢查Haske泵的狀態。198. Check the suction gauge reading.檢查進口壓力表讀數。199. Check the governor handle position.檢查調速手柄位置。200. Change unit to UCP/LGB/SCS control.（UCP unit control panel，LGB local governor board, SCS station control system.將設備轉為UCP/LG

44、B/SCS控制。201. Start /stop Gen. A /B /C.啟動/停止機發電機A / B / C。202. Emergency stop Gen. A/B/C.緊急停止發電機A / B / C。203. Share loading between Gen. A & C.由發電機A和C分擔負載。204. Isolate start air cylinder of Gen. A/B/C.隔離發電機A / B / C的啟動空氣壓縮罐。205. Adjust the frequency of Gen. A.調整發電機A. 的頻率。206. Check lube oil pump sta

45、tus.檢查滑油泵的位置。207. Change engine to UCP/LGB/ASP control.將發動機轉為UCP/LGB/ ASP控制。208. Close /trip Gen.A/B/C.關閉/跳車發電機A / B / C。209. Start/stop open/close system drain pump.啟動/停止打開/關閉系統的排水泵。210. Re-inject crude oil to mainline.回注原油到管道干線。211. Monitor the tank level.監察罐位。212. Vent the pig launcher/receiver.給

46、收/發球筒排氣。213. Launch the pig / Pig arrived.發送球/球到了。214. Open the pig receiver.打開清管器接收裝置。215. Assemble the new pig.組裝新清管球。216. Filling the diesel daily tank on auto.給汽車的柴油日用罐加油。217. Filling the crude fuel tank from suction header.從進口匯管給原油燃料罐加油。218. Check the crude fuel meter readings.檢查原燃料水表讀數。219. Ch

47、eck the crude/diesel tank level.檢查原油/柴油罐的液位。220. Check the crude fuel tank temperature.檢查原燃料箱的溫度。221. No leak is found and accessories are all ready for the tanks無泄漏被發現，泵的配件都是現成的。222. Connected valve is opened and closed for one time, the run is normal連接閥開啟和關閉各一次，運行是正常的。223. Level switch and level g

48、auge are all ready. 液位開關和液位計都準備好了。224. The run is normal. 運行是正常的。225. Pressure gauge and differential pressure gauge have calibration certificates.壓力表，差壓表有校準證書。226. Flow meter FT-28051 are all ready.流量計的FT -28051齊全。227. Connected valve is opened and closed for one time, no leak is found. 連接閥開啟和關閉各一次

49、，無泄漏被發現。230. No leaking.無泄漏。231. Water can be found at every water supply point and no leak is found.每一個供水點都有水，沒有發現泄漏。232. The run of electrical heat tracing is normal.電伴熱的運行是正常的。 233. Level transmitter LT-29601 has calibration certificates. 液位變送器LT 29601有校準證書。234. Thermal resistance TE-29601 are all ready. 熱電阻TE -29601齊全。235. Level switch LSHH-29601A and LSLL-29601B are all ready. 液位開關LSHH - 29601A和LSLL - 29601B都準備好了。 236. Start-up and run are normal.啟動和運行是正常的。237. Pressure gauge PI-29601 has calibration certificates.壓力表PI - 29601有校準證書。238. Pressure safety valve PSV-