涂料物化性能測試技術

1、1/29/2022Prepareed by: Liu Chenzhong2漆膜缺陷原因分類:Product problems)Application problems) Equipment problems) Environment Cause) (Colour problems) 1/29/2022Prepareed by: Liu Chenzhong3漆膜硬度不夠（漆膜硬度不夠（weak):描述描述(DESCRIPTION)表現為漆膜軟表現為漆膜軟, 很容易被很容易被劃傷；劃傷； 相應的相應的耐溶劑性能表現耐溶劑性能表現差。差。1/29/2022Prepareed by: Liu Chen

2、zhong4原因（原因（cause)： 通常是漆膜樹酯交鏈不夠好通常是漆膜樹酯交鏈不夠好，而交鏈不夠的主要因素有：而交鏈不夠的主要因素有：樹酯分子選擇不合適；樹酯分子選擇不合適；未完全干燥；未完全干燥；高溫漆或雙組份漆烘烤溫度不夠；高溫漆或雙組份漆烘烤溫度不夠；雙組份漆固化劑配比不對。雙組份漆固化劑配比不對。1/29/2022Prepareed by: Liu Chenzhong5起泡（起泡（blowing)：1/29/2022Prepareed by: Liu Chenzhong6起泡的原因起泡的原因(cause)：通常是基底有銹跡通常是基底有銹跡(擴大）擴大）、污垢、小、污垢、小凹孔、磷化

3、渣質、水汽等被封在漆膜凹孔、磷化渣質、水汽等被封在漆膜底下，漆膜在烤干或受熱底下，漆膜在烤干或受熱（受熱膨脹）（受熱膨脹）時，這些物質彭漲將漆膜頂起造成。時，這些物質彭漲將漆膜頂起造成。1/29/2022Prepareed by: Liu Chenzhong7起泡的原因：起泡的原因：底下有底下有Money!1/29/2022Prepareed by: Liu Chenzhong8溶劑泡（溶劑泡（Solvent Popping ）描述（描述（DESCRIPTION）新噴漆膜表面有直徑小于新噴漆膜表面有直徑小于1MM的小氣泡。的小氣泡。Open topped blisters up to 1mm

4、in diameter on the surface of the most recently applied paint film.1/29/2022Prepareed by: Liu Chenzhong9溶劑泡（溶劑泡（Solvent Popping ）起因（起因（CAUSE）Air or solvent vapour trapped by fast drying paint forming a skin. This may be due to:a) 天那水太差或太快干。天那水太差或太快干。poor quality or too fast thinner. b) 噴得太厚或兩層漆之間干燥時

5、間不夠。噴得太厚或兩層漆之間干燥時間不夠。excessive film thickness, or insufficient drying time between coats. c) 壓縮空氣壓力太低。壓縮空氣壓力太低。compressed air pressure too low. d) 加熱太快。加熱太快。drying temperature too high, heat source too close to the film, too hot, or applied too soon.1/29/2022Prepareed by: Liu Chenzhong10溶劑泡（溶劑泡（Solv

6、ent Popping ）n預防（預防（PREVENTION）na) 確保工件表面清潔確保工件表面清潔Ensure that the surface is scrupulously clean.nb) 使用合適的天那水。使用合適的天那水。Use only recommended thinner.nc) 每層漆膜厚度合適，并適當閃干每層漆膜厚度合適，并適當閃干Apply paint in thin, wet films. Allow sufficient drying time between coats.nd) 使用正確的噴漆壓力使用正確的噴漆壓力Use correct compressed

7、air pressure.ne) 烘烤前適當流平，避免加熱過快，熱源過近。烘烤前適當流平，避免加熱過快，熱源過近。Allow sufficient flash off time before force drying, ensure that the correct drying temperature is not exceeded. Do not allow the heat source to be placed too close to the surface.1/29/2022Prepareed by: Liu Chenzhong11針孔（針孔（Pinholing）描述（描述（DES

8、CRIPTION）小凹穴，通常直徑小于小凹穴，通常直徑小于1MM。Small cavities, generally less than 1 mm in diameter, 1/29/2022Prepareed by: Liu Chenzhong12針孔（針孔（Pinholing）預防（預防（PREVENTION ）a)一次不要噴得太厚。一次不要噴得太厚。Do not spray too thick one time, b)烘烤之前適當流平。烘烤之前適當流平。Flashing the film before baking.c) 使用涂料廠商推薦的附料。使用涂料廠商推薦的附料。Use only

9、recommended materials. d) 正確調配油漆，使用較慢干稀釋劑。正確調配油漆，使用較慢干稀釋劑。Mix the paint correctly, use slow dry thinner.E）保持底材干凈。保持底材干凈。)Keep materials clean.1/29/2022Prepareed by: Liu Chenzhong13魚眼魚眼/ Fish Eyes (cissing)好可愛噢，真的象魚眼睛呢！1/29/2022Prepareed by: Liu Chenzhong14產生魚眼的原因產生魚眼的原因(cause)：放大之后中間有核放大之后中間有核,通常是通常

10、是*素材被含硅素材被含硅silicon類的物質污染。類的物質污染。*素材未很好清潔。素材未很好清潔。* *裸手接觸工件。裸手接觸工件。* *油漆一次噴涂太濕。油漆一次噴涂太濕。* *油漆體質敏感。油漆體質敏感。1/29/2022Prepareed by: Liu Chenzhong15預防預防(PREVENTION)魚眼的產生魚眼的產生a) Keep the part away from silicone pollution b) Thoroughly clean the surface with wax and grease remover. Do not allow cleaning so

11、lvents to dry on the surface but remove with a clean dry cloth,c) Always use the recommended materials. d) Ensure that the spraying area is properly ventilated.1/29/2022Prepareed by: Liu Chenzhong16與魚眼相似的其它缺陷與魚眼相似的其它缺陷 1.水泡水泡(blister)n工件表面被濺上水珠。n你見過水性漆出現此缺陷嗎？1/29/2022Prepareed by: Liu Chenzhong17與魚眼

12、相似的其它缺陷與魚眼相似的其它缺陷 2.油污油污(oil pollution)n工件表面被輕質油工件表面被輕質油污染污染.1/29/2022Prepareed by: Liu Chenzhong18起云起云/斑紋斑紋,(Clouding / Mottling )1/29/2022Prepareed by: Liu Chenzhong19起云起云/斑紋斑紋,(Clouding / Mottling )起因起因:常見于銀粉漆，主要是銀粉排列不一致。主要原因有：十字交叉噴涂；使用太差的稀釋劑；或稀釋劑加入太少。槍未調好；噴涂手法不正確。 5素材厚薄不一（這種情況常叫應力紋）。1/29/2022Pre

13、pareed by: Liu Chenzhong20應力紋應力紋(mapping):在5220機殼上常出現應力紋的地方1/29/2022Prepareed by: Liu Chenzhong21臟點臟點/塵點塵點/異色點異色點(Dirt / threads / Bits) 1/29/2022Prepareed by: Liu Chenzhong22臟點臟點/纖維纖維/異色點（異色點（Dirt / threads / Bits）1/29/2022Prepareed by: Liu Chenzhong23臟點臟點/纖維纖維/異色點（異色點（Dirt / threads / Bits）n此類缺陷目前

14、占有此類缺陷目前占有相當大的比例，您相當大的比例，您知道其主要原因是知道其主要原因是什么嗎什么嗎？1/29/2022Prepareed by: Liu Chenzhong24顆粒顆粒(particles)產生原因產生原因素材本身灰塵未被去除；素材本身灰塵未被去除；油漆未過濾，油漆未過濾， 或?yàn)V網太粗或?yàn)V網太粗或太臟；或太臟；噴房、流平間、烤房等環噴房、流平間、烤房等環境被污染；境被污染；調漆間臟污，油漆未蓋好；調漆間臟污，油漆未蓋好；調漆罐、供漆管路、噴槍調漆罐、供漆管路、噴槍清洗不夠。清洗不夠。壓縮空氣未過濾，或?yàn)V網壓縮空氣未過濾，或?yàn)V網太臟。太臟。1/29/2022Prepareed by

15、: Liu Chenzhong25纖維或毛絲：纖維或毛絲：n主要來自衣服纖維，主要來自衣服纖維，人員走動太多，未人員走動太多，未穿防塵衣。穿防塵衣。n也有來自劣質空氣也有來自劣質空氣過濾網。過濾網。1/29/2022Prepareed by: Liu Chenzhong26當這類缺陷很多時，當這類缺陷很多時， 怎么辦？怎么辦？What can I do?1/29/2022Prepareed by: Liu Chenzhong27建議n當這類缺陷很多時，建議將缺陷樣品抽當這類缺陷很多時，建議將缺陷樣品抽取取30-5030-50片進行詳細分類（有必要的話，片進行詳細分類（有必要的話，使用放大鏡觀察

16、缺陷形狀、顏色等），使用放大鏡觀察缺陷形狀、顏色等），然后分析原因然后分析原因 改善改善 檢察改善效果檢察改善效果 制定制定SOP SOP 貫徹執行貫徹執行SOPSOP。1/29/2022Prepareed by: Liu Chenzhong28干噴干噴/異常光澤低異常光澤低（Dry spray/loss of gloss)描述（描述（DESCRIPTION）雖然漆膜表面光滑雖然漆膜表面光滑,但漆膜表面光澤異常偏低但漆膜表面光澤異常偏低. Although apparently smooth and evenly applied, the surface lacks shine.1/29/20

17、22Prepareed by: Liu Chenzhong29n起因起因(CAUSE)nMicroscopic roughness of the surface which may result from:na)底漆太差或底漆未干就噴面漆底漆太差或底漆未干就噴面漆. poor hold out of primer, or the application of topcoat over primer which is not thoroughly dry.nb)稀釋劑太差或加了不合適的添加劑稀釋劑太差或加了不合適的添加劑. poor quality or incorrect thinner, o

18、r the use of additives in the paint. nc) 素材前處理不當或噴漆手法不對素材前處理不當或噴漆手法不對. incorrectly prepared or poorly applied paint.nd)素材質量太差素材質量太差application over a poor substrate. ne) 高濕低溫時漆膜干燥太慢高濕低溫時漆膜干燥太慢. excessively slow drying due to high humidity or low temperature.nf)溶劑蒸氣在漆膜表面冷凝溶劑蒸氣在漆膜表面冷凝. solvent fumes o

19、r exhaust gases attacking the surface.ng)表面被污染表面被污染. surface contamination by wax, grease, oil, soap or water.1/29/2022Prepareed by: Liu Chenzhong30預防（預防（PREVENTION ）a) 選擇正確種類和比例的稀釋劑選擇正確種類和比例的稀釋劑Use the correct proportion of recommended thinner.b) 正確的噴漆手法正確的噴漆手法: 槍距槍距, 扇形扇形, 氣壓氣壓Use correct spraying

20、 techniques, ensure that equipment is clean, set air pressure as low as possible, consistent with proper atomisation, spray from the correct distance.c) 使用合適的噴房使用合適的噴房, 確保噴房有良好的空確保噴房有良好的空氣流通氣流通. Use a spray booth, and ensure that air circulation and extraction is at the correct velocity.1/29/2022Pre

21、pareed by: Liu Chenzhong31漆膜太薄漆膜太薄Inadequate Colour Coverage描述（描述（DESCRIPTION）漆膜過薄可見底材漆膜過薄可見底材, 通常出現在比較難噴涂的底通常出現在比較難噴涂的底側面等地方側面等地方. Underlying surfaces visible through the paint film, most frequently in hard to spray areas, on lower panels or on sharp edges and contours.1/29/2022Prepareed by: Liu Ch

22、enzhong32n預防（預防（PREVENTION）na) 使用合適的噴涂方法確保合適的漆膜使用合適的噴涂方法確保合適的漆膜厚度厚度. Use the correct spraying technique, ensure even and adequate film thickness.nb) 使用合適的治具使用合適的治具, 合適的燈光照明合適的燈光照明; 特特別注意難噴涂表面別注意難噴涂表面. Work under good lighting conditions in a properly sized spray booth, pay special attention to inacc

23、essible areas.nc) 確保漆料混合均勻確保漆料混合均勻. Ensure that the materials are thoroughly mixed. 1/29/2022Prepareed by: Liu Chenzhong33橘皮（橘皮（Orange Peel ）描述（描述（DESCRIPTION ）漆膜表面不平整如同桔子皮表面. Pebbled, uneven surface of the paint film, similar in appearance to orange skin.1/29/2022Prepareed by: Liu Chenzhong34橘皮（橘皮（

24、Orange Peel）起因起因(CAUSE)a) 噴漆手法太差噴漆手法太差, 槍距槍距, 空氣壓力、出漆量調節不空氣壓力、出漆量調節不合適。合適。b) 漆膜不要噴得太厚或太薄。漆膜不要噴得太厚或太薄。c) c) 油漆品質太差、粘度調整不合適、混合不均油漆品質太差、粘度調整不合適、混合不均勻。勻。 d) 兩層漆之間干燥不夠。兩層漆之間干燥不夠。Insufficient drying time between coats. e) 工件表面溫度不正常。工件表面溫度不正常。Incorrect ambient or surface temperature, draughts.1/29/2022Prep

25、areed by: Liu Chenzhong35橘皮（橘皮（Orange Peel）n預防（PREVENTION ）na)使用正確的噴漆手法、正確調節噴槍。Use the correct spraying technique and ensure that equipment is correctly adjustednb)均勻噴漆。nc)使用合適的天那水，并調節到合適的粘度。 Ensure that the paint is correctly mixed, use only recommended thinner with the correct gradend) 兩層漆之間充分干燥。A

26、llow sufficient drying time between coatsne) 在合適的溫度范圍內和良好的空氣流通條件下噴漆。Spray within the re-commended temperature range and ensure proper ventilation1/29/2022Prepareed by: Liu Chenzhong36流掛（Runs / Sags ）描述描述(DESCRIPTION )通常在垂直面等處，出現漆膜局部過厚造成大波紋、通常在垂直面等處，出現漆膜局部過厚造成大波紋、乳頭現象。乳頭現象。Well defined local thickeni

27、ng of the paint film in the form of a wavy line or shallow, rounded ridges, normally confined to sharply sloping or vertical surfaces.1/29/2022Prepareed by: Liu Chenzhong37流掛（流掛（Runs / Sags ）n起因（起因（CAUSE） nSlumping of the paint film due to:na)噴得過厚，空氣壓力太低，扇形太窄，槍距太近，噴得過厚，空氣壓力太低，扇形太窄，槍距太近，運槍太慢。運槍太慢。Exc

28、ess thickness of application, air pressure too low, fan width too narrow, spray gun too close to the surface or moving too slowly.nb)使用太差的天那水。使用太差的天那水。Use of poor quality or incorrect thinner.nc)粘度調整不正確。粘度調整不正確。Incorrect viscosity of the paint. nd) 素材表面或氣溫太低。素材表面或氣溫太低。Air or surface temperature too low. ne) 表面臟污。表面臟污。C