加工中心精度檢驗規范標準

1、NO.日沛甯配件（上海）有限公司RI PEI computer accessory (Shanghai) Co., Ltd.加工中心精度檢驗規靶機型：MODEL機號：SERIAL NO.目錄CATALOGUE1.0靜態精度檢查 6頁P(yáng)AGESTATIC ACCURACY INSPECION2.0定位精度檢查 1頁P(yáng)AGEPOSITION ACCURACY INSPECTION3.0重復精度檢查1頁P(yáng)AGEREPETITIONAL ACCURACY INSPECTION4.0循圄精度1頁P(yáng)AGEPALLET ACCURACY5.0附件 頁P(yáng)AGEACCESSARY共頁P(yáng)AGE中閾上海松江顯新槁申

2、港路3636虢No.3636 Shenggang Road,Xin Qiao Songjiang ShanghaiChina核準者 CONFIRMED檢驗者CHECKED檢驗 日期 DATEMCV F01S001Q301000003940331-71.0 靜態精度 STATIC ACCURACY INSPECTION單位Unit :mm項 次 NO檢查項目Inspection item測試方法圖 Measuring method diagram許可差 Permissible deviation實際測量值 Measured value1.1床臺X軸 方向運動 之真直度 Straightn ess

3、 of the X axismovemen ta.X-Z 面內L0.06/10001I.b.Y-Z 面內a111.2床臺Y軸 方向運動 之真直度 Straightn ess of the Y axismovemen ta.X-Z 面內0.06/1000D -1i b.Y-Z 面內mm項次NO檢查項目Inspection item床臺X軸方向之 運動與其上面之 平行度 Parallelismbetween1.3movement in Xaxis directionand table upper surface床臺Y軸方向之 運動與其上面之 平行度 Parallelismbetween1.4mov

4、ement in Yaxis directionand table upper surfaceX軸方向運動與 床臺基準溝側面 之平行度 Parallelismbetween1.5movement inaxis directionandSidesurface of tablereference slot測試方法圖Measuring methoddiagramJ3中許可差Permissible deviationXW 5000.02500VXW 8000.025800VXW 1250 0.031250VXW 20000.04YW 5000.02500VYW 8000.025800VYW 1250

5、0.031250VYW 20000.04每300mm的量測距離下許可差為0.015mm0.015for a measuringlength of 300測量值Measured value項 次 NO檢查項目Inspection item測試方法圖Measuring method diagram許可差 Permissible deviation實際測量值 Measured value各軸方向 相互運動 之直角度 Perpendi cularity Betweenmovemena.X-Y 軸 Placei iO=0.012/300t in Xaxisdirection b.and Y X-Zaxi

6、s 軸11.6 direction Placeand Z axisLIH10.012/300一n 5directionc.Y-Z軸Place主軸中心線與床 臺面之直角度Perpendicularit y between 1.7 centerline ofmain spindleand tablesurface.0.012/300旋徑每300Per3000.015單位 Unit : mm項 次 NO檢查項目Inspection item測試方法圖Measuring method diagram許可差Permissible deviation主軸孔內面之偏 擺Run out of1固定端At sp

7、indle side end of1.8spindle taper holeJ丁o=test bar 0.005 固定端300處 At 300 position0.015實 際測量值Measured value主軸軸線與Z軸 軸線運動間的平 行度Parallelism1.9 between the spindle axis andthe Z-axismotion一主軸在Z軸方向 之移（松）動量Movement of1.1 main spindle in 0 Z axis directiona:0.015/300b:0.015/3000.0051.11主軸端面之偏擺 Run out of mai

8、n spindle outer surface1飛10.011.12主軸外面之偏擺 Run out of main spindle outer surface1i1; _r -1-40.01mm1.13床槨X軸方向 勤之直度 Straightness of table movement in the X axis.1 .Apply a fixed indicator to the straight edge as the figure shown.2 .Adjust to get reading at both ends of the straight edge.3 .Move the tab

9、le 300 mm in X-axis direction.4 .Record the largest value difference as the measurement value.0.01/3001.14床槨Y軸方向 勤之直度 Straightness of table movement in the Y axis1 .Apply a fixed indicator to the straight edge as the figure shown.2 .Adjust to get reading at both ends of the straight edge.3 .Move the

10、 table 300 mm in X-axis direction.4 .Record the largest value difference as the measurement value.0.01/3001.15旋斡槨旋斡偏擺 TObTeR*''''' 1二二10.015mm/300111yA =1.16旋斡槨旋斡偏擺Table runout(Z)d1?1 11-滬*rp0.005mm1.17卓刀角度摸刀接 重定位精度 Repeatability of tool angle after tool change.0.001mm1.18卓刀角度停止接

11、 重定位精度 Repeatability of tool angle after tool stop.0.001mm12更刀加*定位 精度Repeatability of 1tool angle after machining part二二二-0：01mm.1.21主軸振勤檢測 Spindle vibration detection三0.6mm/s (Ref)2.0 定位精度檢查 Positioning accuracy inspection Unit : mm項 次 NO檢查項目 Inspection item測試方法圖Measuring method diagram許可差 Permissi

12、ble deviation實際測量值 Measured value2.1直線運動之 定位精度 ISO230-2 循環次數： 2次 Positioning accuracy of straight line movemen t By ISO230-2 Cycle times :Two timesXLW1000 0.01 1000VL三2000 0.015L三2000 0.02Y-LJ-kJ-Q一和-iZ單位 Unit: sec2.2回轉運動之 定位精度 Positioning accuracy of straight line movement By ISO230-2 Cycle times :

13、Two timesC153.0 反復精度檢查 Repetition accuracy inspection Unit: sec項 次 NO檢查項目 Inspection item測試方法圖Measuring method diagram許可差 Permissible deviation實際測量值 Measured value3.1直線運動之 反復定位精 度 ISO230-2 Positioning repeatabil ity of straight line movement By ISO230-2 Cycle times :TwotimesX0.006Hi-。&二gY-1=Z單位

14、Unit: sec3.2回轉運動之重 復定位精度 ISO230-2Positioning repeatability of straight line movement By ISO230-2 Cycle times :Two timesC83.0 反復精度檢查 Repetition accuracy inspection Unit: sec項 次 NO檢查項目 Inspection item測試方法圖Measuring method diagram許可差 Permissible deviation實際測量值 Measured value3.3Max reversal value 最大反沖值Position accuracy qualified toISO230-2X。&二g0.006YfZ單位4.0 循圄精度檢查 Repetition a