汽車專業詞匯

1、汽車外設 front wheel 前輪 rear wheel 后輪 tread 輪距 chassis 底盤 bodywork, body 車身 rear window 后窗玻璃 windscreen 擋風玻璃 windscreen wiper 雨刮器 fender, wing, mudguard 擋泥板 radiator grille 水箱 wing mirror 后視鏡 bonnet 發動機蓋 boot 行李箱 roof rack, luggage rack 行李架 license plate, number plate 車號牌 wing 前翼子板 hubcap 輪轂罩 bumper 保險杠

2、 front blinker 前信號燈 taillight, tail lamp 尾燈 backup light, reversing light 倒車燈 stoplight, stop lamp 剎車燈 rear blinker 轉彎指示燈 trunk, boot 行李箱 bumper 保險杠 tailpipe 排氣管 汽車內部 back seat, rear seat 后座 drivers seat, driving seat 駕駛席 passenger seat 旅客席 steering wheel, wheel 方向盤 rear-view mirror, driving mirror

3、后視鏡 horn, hooter 喇叭 choke 熄火裝置 gear stick, gear change 變速桿 gearbox 變速箱 starter, self-starter 起動器,起動鈕 brake pedal 剎車踏板 clutch pedal 離合器踏板 hand brake 手制動器 foot brake 腳制動器 dashboard 儀表板 milometer 里程表 speedometer, clock 速度表 transmission 傳動 piston 活塞 radiator 散熱器 fan belt 風扇皮帶 shaft 傳動軸 inner tube 內胎 dra

4、in tap 排氣閥門 silencer 消音器 tank 油箱 overflow 溢流孔 valve 閥門 exhaust pipe 排氣管 spare wheel 備胎,備用輪胎 carburettor 汽化器工位 station 吊運裝置 overhead hoist 更衣室 restroom 1號廠房工藝布置方案圖 proposal of the Plant I layout 合籠 mate 底盤平移臺 chassis shuttle 車輛轉移臺 bus transfer 前圍角板 front wall angle cover 后圍側板 rear wall side cover 保險杠

5、 bumper 三類底盤 three type chassis 左側圍應力蒙皮 R/S stretching skin (road side) 中涂 floating coat 拼裝臺 collector 切割輪口 wheel -arch cutting 內飾 trim 線束 harness 返工 re-doing 輪罩護板 wheel house 發車前準備 pre-delivery 舉升 hoist 小批量產品 be pilot 2 套 two kits 配電站 power transformer substation 裙板 skirt 發動機托架 engine holding frame

6、 診斷報警系統 diagnosis and alarming system 互換性 interchangeability 縮微圖紙 microfiche files 總裝 final assembly 磷化 phosphating 儀表板 dash board 切齊 trimming 結構完整性 structure integrity 自動愈合的防腐材料 self-healing corrosion preventative material 長途客車 inter-city bus 改裝廠 refitting factory 遮陽板 sun visor 隨車工具 tool box 鋼化玻璃 t

7、oughened grass 異形鋼管 special steel pipe 全天候空調系統 full range A/C 強制通風 ram-air ventilation 停機時間 downtime 無公害柴油 clean diesel 寬敞懸臂式座椅 roomy cantilevered seat 防滑地板 no-skid floor 織物紋里鋁合金 textured aluminum extrution 爬坡能力 grade ability 排水閥 drain valve 除濕器 moisture ejector 怠速時 at idle 琴式驅動橋 banjo type drive ax

8、le 通風口 duct 恒溫控制 thermostatic control 平衡水箱 surge tank 變光開關 simmer switch 消音器 muffler 防破壞 vandal resistant 聚碳化透鏡 poly-carbonate len 鍍鋅板 galvanized plate 搭接 lap 亮麗的外表  smart apperance 隱藏式固定 concealed fastening 水洼 ponding 發動機中置式客車 bus with under floor engine 組合式客車車身 modular bus body 薄殼式結構 she

9、ll construction 襯墊 pad 空氣導流板 air deflector 擱梁 shelf beam 腰梁 waist rail 梭梁 stabilizing beam 腰帶式安全帶 diagonal safety belt 壓條 trim strip 嵌條 insertion strip 翼板 fender 斜撐 bracing piece 轉向盤回正性試驗test of steering wheel returnability轉向盤轉角脈沖試驗steering wheel impulse input test轉向盤轉角階躍輸入試驗steering wheel step inpu

10、t or transient state yaw response test極限側向加速度試驗limiting lateral acceleration test汽車平順性隨機輸入行駛試驗automobile ride random input running test汽車平順性單脈沖輸入行駛試驗automobile ride single pulse input running test汽車懸掛系統固有頻率與阻尼比的測定試驗measurement of natural frequency and damping raito of suspension功率突然變化影響試驗test of eff

11、ect of sudden power change收油門后控制試驗test of control at breakway橫風穩定性試驗test of crosswind stability反沖試驗kick-back test輪胎爆破響應時間試驗test of burst response of tyre繞過障礙物試驗obstacle avoidance test移線試驗lane change testJ型轉彎試驗test of J turn頻率響應時間試驗frequency response test瞬態響應時間試驗transient response test階路響應時間試驗step re

12、sponse test脈沖響應試驗pulse response test靜態操舵力試驗static steering effort test懸架舉升試驗jack-up test of suspension耐翻傾試驗test of overturning immunity輪輞錯動試驗rim slip test風洞試驗wind tunnel test制動穩定性試驗test of braking stability最小轉彎直徑試驗minimum turning diameter test操舵力試驗steering effort test汽車發動機類型type發動機engine內燃機intenal c

13、ombusiton engine動力機裝置power unit汽油機gasoline engine汽油噴射式汽油機gasoline-injection engine火花點火式發動機spark ignition engine壓燃式發動機compression ignition engine往復式內燃機reciprocating internal combustion engine化油器式發動機carburetor engine柴油機diesel engine轉子發動機rotary engine旋輪線轉子發動機rotary trochoidal engine二沖程發動機two-stroke eng

14、ine四沖程發動機four-stroke engine直接噴射式柴油機direct injection engine間接噴射式柴油機indirect injection engine增壓式發動機supercharged engine風冷式發動機air-cooled engine油冷式發動機oil-cooled engine水冷式發動機water-cooled engine自然進氣式發動機naturally aspirated engine煤氣機gas engine液化石油氣發動機liquified petroleum gas engine柴油煤氣機diesel gas engine多種燃料發動

15、機multifuel engine石油發動機hydrocarbon engine雙燃料發動機duel fuel engine熱球式發動機hot bulb engine多氣缸發動機multiple cylinder engine對置活塞發動機opposed piston engine對置氣缸式發動機opposed-cylinder engine十字頭型發動機cross head engine直列式發動機in-line engine星型發動機radial engine筒狀活塞發動機trunk-piston engine斯特林發動機stirling engine套閥式發動機knight engine

16、氣孔掃氣式發動機port-scavenged engine傾斜式發動機slant engine前置式發動機front-engine后置式發動機rear-engine中置式發動機central engine左側發動機left-hand engine右側發動機right-hand engine短沖程發動機oversquare engine長沖程發動機undersquare engine等徑程發動機square engine頂置凸輪軸發動機overhead camshaft engine雙頂置凸輪軸發動機dual overhead camshaft engineV形發動機V-engine頂置氣門發動

17、機valve in-head engine側置氣門發動機side valve engine無氣門發動機valveless engine多氣門發動機multi-valve engine臥式發動機horizontal engine斜置式發動機inclined engine立式發動機vertical engineW形發動機w-engineI形發動機I-engineL形發動機L-engineF形發動機F-engine性能performance二沖程循環two-stroke cycle四沖程循環four-stroke cycle狄塞爾循環diesel cycle奧托循環otto cycle混合循環mix

18、ed cycle定容循環constant volume cycle工作循環working cycle等壓循環constant pressure cycle理想循環ideal cycle熱力循環thermodynamic cycle沖程stroke活塞行程piston stroke長行程long stroke上行程up stroke下行程down stroke進氣行程intake stroke充氣行程charging stroke壓縮行程compression stroke爆炸行程explosion stroke膨脹行程expansion stroke動力行程power stroke排氣行程ex

19、haust stroke膨脹換氣行程expansion-exchange stroke換氣壓縮行程exchange-compression stroke止點dead center上止點top dead center(upper dead center)下止點lower dead center(bottom dead center)上止點前budc(before upper dead center)上止點后atdc(after top dead cetner)下止點前bbdc(before bottom dead center)下止點后abdc(after bottom dead center)

20、缸徑cylinder bore缸徑與行程bore and stroke空氣室energy chamber氣缸余隙容積cylinder clearance volume燃燒室容積combustion chamber volume氣缸最大容積maximum cylinder volume壓縮室compression chamber排氣量displacement發動機排量engine displacement活塞排量piston swept volume氣缸容量cylinder capacity單室容量single-chamber capacity容積法volumetry壓縮比compression

21、 ratio臨界壓縮比critical compression ratio膨脹比expansion ratio面容比surface to volume ratio行程缸徑比stroke-bore ratio混合比mixture ratio壓縮壓力compression pressure制動平均有效壓力brake mean effective pressure(bmep)空燃比air fuel ratio燃空比fuel air ratio燃料當量比fuel equivalence ratio扭矩torque單缸功率power per cylinder升功率power per liter升扭矩to

22、rque per liter升質量mass per liter 減額功率derating power輸出馬力shaft horsepower馬力小時，馬力時horsepower-hour總馬力gross horse power總功率gross power 凈功率net power 燃油消耗量fuel consumption 比燃料消耗率specific fuel consumption空氣消耗率air consumption機油消耗量oil consumption有效馬力net horse power額定馬力rated horse power馬力重量系數horsepower-weight fa

23、ctor制動功率brake horse power制動熱效率brake thermal efficiency 總效率overall efficiency排煙極限功率smoke limiting horsepower功率曲線power curve機械損失mechanical loss機械效率mechanical efficiency有效熱效率effective thermal efficiency充氣系數volumetric efficiency過量空氣系數coefficient of excess air適應性系數adaptive coefficient扭矩適應性系數coefficient o

24、f torque adaptibility轉速適應性系數speed adaptive coefficient強化系數coefficient of intensification校正系數correction factor換算系數conversion factor活塞平均速度mean piston speed發動機轉速engine speed (rotational frequency)怠速轉速idling speed經濟轉速economic speed起動轉速starting speed最低穩定工作轉速lowest continuous speed with load最大扭矩轉速speed at

25、 maximum torque最高空轉轉速maximum no load governed speed調速speed governing 超速overspeed怠速idling轉速波動率speed fluctuation rate工況working condition(operating mode)額定工況declared working condition變工況variable working condition穩定工況steady working condition空載no-load全負荷full load超負荷overload部分負荷part load充量（進氣）charge旋轉方向di

26、rection of rotation順時針clockwise逆時針counter-clockwise左轉left-hand rotation右轉right-hand rotation外徑major diameter中徑pitch diameter內徑minor diameter徑向間隙radial clearance發動機性能engine performance加載性能loading performance起動性能starting performance加速性能acceleration performance動力性能power performance排放性能emission performa

27、nce空轉特性no load characteristics負荷特性part throttle characteristics調速特性governor control characteristics萬有特性mapping characteristics穩定調速率steady state speed governing rate氣缸體和氣缸蓋cylinder block and head氣缸體cylinder block整體鑄造cast inblock (cast enblock)發動機罩engine bonnet氣缸體加強筋engine block stiffening rib氣缸cylind

28、er（轉子機）缸體stator缸徑cylinder bore氣缸體機架cylinder block frame氣缸蓋cylinder head配氣機構箱valve mechanism casing氣缸體隔片cylinder spacer氣缸蓋密封環cylinder head ring gasket氣缸蓋墊片cylinder head gasket氣缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner濕式缸套wet cylinder liner氣缸水套water jacket膨脹塞expansion plug防凍塞freeze plug氣

29、缸壁cylinder wall環脊ring ridge排氣口exhaust port中間隔板intermediate bottum導板guideway創成半徑（轉子機）generating radius缸體寬度（轉子機）operating width機柱column燃燒室combustion chamber主燃燒室main combustion chamber副燃燒室subsidiary combustion chamber預燃室prechamber渦流燃燒室swirl combustion chamber分開式燃燒室divided combustion chamber渦流式燃燒室turbul

30、ence combustion chamber半球形燃燒室hemispherical combustion chamber浴盆形燃燒室bathtub section combustion chamberL形燃燒室L-combustion chamber楔形燃燒室wedge-section combustion chamber開式燃燒室open combustion chamber封閉噴射室closed spray chamber活塞頂內燃燒室piston chamber爆發室explosion chamber燃燒室容積比volume ratio of combustion cahmber燃燒室

31、口徑比surface-volume ratio of combustion chamber通道面積比area ratio of combustion chamber passage曲軸箱通氣口crankcase breather凸輪軸軸承座camshaft bearing bush seat定時齒輪室罩camshaft drive(gear)cover曲軸箱檢查孔蓋crankcase door曲軸箱防爆門crankcase explosion proof door主軸承蓋main bearing cap氣缸蓋罩valve mechanism cover飛輪殼flywheel cover掃氣儲器

32、scavenging air receiver活塞piston裙部開槽活塞split skirt pistonU形槽活塞U-slot piston滾花修復活塞knurled piston圓頂活塞dome head piston平頂活塞flat head piston凸頂活塞crown head piston(convex head piston)凹頂活塞concave head piston階梯頂活塞step-head piston筒形活塞trunk piston橢圓形活塞oval piston抗熱變形活塞autothermic piston不變間隙活塞constant clearance p

33、iston鑲因瓦鋼片活塞invar strut piston直接冷卻式活塞direct-cooled piston間接冷卻式活塞indirect cooled piston滑裙活塞slipper piston活塞速度piston speed活塞頂部piston head活塞裙部piston skirt整體活塞裙solid skirt活塞裙擴大襯簧piston skirt expander滑履式活塞裙slipper skirt隔熱槽heat dam活塞標記piston mark活塞銷piston pin活塞銷孔piston pin boss活塞銷襯套piston pin bushing全浮式活塞

34、銷full-floating piston pin半浮式活塞銷semifloating piston pin固定螺釘式活塞銷set screw piston pin活塞環piston ring組合式活塞環compound piston ring同心活塞環concentric piston ring偏心活塞環eccentric piston ring自由環free ring閉合環closed ring梯形環keystone ring半梯形環half keystone ring矩形環rectangular ring油環oil control ring開槽油環slotted oil control

35、ring螺旋彈簧加載雙坡口油環coil spring loaded slotted oil control ring 漲環expander雙坡口油環double bevelled oil control ring內上坡口internal bevel top內下坡口internal bevel bottom邊緣坡口油環bevelled-ege oil control ring刮油環scrapper ring鉤形環napier ring鍍鉻活塞環chrome plated piston ring活塞襯環piston ring expander活塞環槽piston ring groove活塞環區ri

36、ng zone活塞環岸piston ring land活塞環內表面back of ring曲柄連桿機構connecting rod中心曲柄連桿機構central-located connecting rod偏心曲柄連桿機構offset connecting rod鉸接曲柄邊桿機構hinged connecting rod連桿connecting rod連桿小頭connecting rod small end連桿大頭connnecting rod big end連桿桿身connecting rod shank副連桿slave connecting rod叉形連桿fork-and-blade co

37、nnecting rod主連桿main connecting rod方形連桿boxed rod絞鏈?zhǔn)竭B桿hinged type connecting rod活節式連桿articulated connecting rod連桿蓋connecting rod cap連桿軸承connecting rod bearing曲軸crankshaft整體式曲軸one-piece crankshaft組合式曲軸assembled crankshaft右側曲軸right-hand crankshaft左側曲軸left-hand crankshaft改變行程的曲軸stroked crankshaft曲軸前端cran

38、kshaft front end曲軸主軸頸crankshaft main journal 軸頸重疊度shaft journal overlap圓角fillet主軸承main bearing曲軸止推軸承crankshaft thrust bearing薄臂軸瓦thin wall bearing shell曲軸油道crankshaft oil passage曲柄crank曲柄臂crank arm曲柄銷crank pin軸套bush曲柄轉角crank angle曲柄半徑crank radius拋油圈oil slander角度輪degree wheel 動平衡機dynamic balancer平衡重b

39、alancer weight扭振減振器torshional vibration damper扭振平衡器torsion balancer諧振平衡器harmonic balancer振動平衡器vibration balancer曲軸鏈輪crankshaft sprocket轉子軸頸rotor journal 偏心軸eccentric shaft曲軸箱crankcase閉式曲軸箱通風裝置closed-crankcase ventilating system飛輪flywheel飛輪齒圈flywheel ring gear飛輪芯棒cantilever飛輪芯軸flywheel spindle飛輪的慣量矩f

40、lywheel moment of inertia飛輪標記flywheel mark當量系統equivalent system當量軸長equivalent shaft length一級往復慣性力reciprocating inertia force,1st order二級往復貫性力reciprocating inertia force, 2nd order離心慣性力centrifugal inertia force配氣機構valve gear凸輪軸camshaft凸輪cam整體式凸輪軸one-piece camshaft組合式凸輪軸assembled camshaft凸輪軸驅動機構camsha

41、ft drive賽車用凸輪軸race camshaft凸輪軸軸頸camshaft bearing journal凸輪軸軸承camshaft bearing 凸輪軸偏心輪camshaft eccentric凸輪軸鏈輪camshaft sprocket凸輪軸正時齒輪camshaft timing gear凸輪軸齒輪camshaft gear wheel 進口凸輪inlet cam排氣凸輪 exhaust cam快升凸輪quick lift cam快升緩降凸輪quick lift gradual clsing cam凸輪輪廓cam contour凸輪包角cam angle凸輪升程cam-lobe l

42、ift凸輪尖cam nose凸輪從動件cam follower齒輪傳動機構gear drive正時齒輪timing gear鏈傳動機構chain drive鏈輪sprocket wheel 鏈輪盤chain sprocket正時鏈條timing chain帶齒皮帶toothed timing belt鏈條張緊輪chain tension gear半速齒輪half speed gear正時齒輪刻印記號timing gear punch mark氣門valve進氣過程intake process換氣過程gas exchange process掃氣過程scavenging process給氣比del

43、ivery ratio分層充氣stratified charge充量系數volumetric efficiency渦流比swirl rate進氣渦流intake swirl螺旋進氣道進氣helical duct intake導流屏式氣門進氣masked valve intake切向進氣道進氣tangential duct intake進氣紊流intake trubulence進氣提前角intake advance angle進氣持續角intake duration angle進氣遲后角intake lag angle進面值time-area value氣門升程valve lift氣門正時val

44、ve timing掃氣口面積scavenging port area菌形氣門mashroom valve, poppet valve鈉冷卻氣門sodium filled valve(natrium cooled valve)雙氣門dual valve進氣門intake valve (suction valve,inlet valve)排氣門exhaust valve頂置氣門overhead valve側置氣門side valve傾斜氣門inclined overhead valve直立氣門vertical overhead valve套筒式滑閥sleeve valve氣門機構valve gea

45、r直接式氣門驅動機構direct valve gear間接式氣門驅動機構indirect valve gear氣門桿valve stem加大氣門桿oversize valve stem氣門頭valve head氣門工作面valve face氣門邊限valve margin氣門彈簧座valve-spring retainer氣門鎖片valve key氣門間隙調節螺釘valve lash adjusting screw氣門旋轉器valve rotator氣門室valve cage氣門油封valve oil seal氣門口valve port氣門座valve seat氣門座鑲?cè)Γㄇ惰偸綒忾T座圈）va

46、lve seat insert(valve seat ring)氣門座錐角valve seat angle氣門座寬度valve seat width氣門挺桿valve tappet(valve lifter)液力挺桿hydraulic tappet(lifter)無間隙挺桿zero-rush tappet (non-clearance tappet)筒形挺桿barrel type tappet油壓挺桿ooil tappet滾輪挺桿roller tappet(lifter)挺桿轉位tappet rotation 排氣門挺桿exhaust valve lifter氣門導管valve guide氣門

47、桿導管stem guide氣門重疊度stem overlap氣門開啟持續時間valve duration 氣門正時標記valve timing sign氣門彈簧valve spring氣門內彈簧inner valve spring氣門外彈簧outer valve spring剛性緩沖彈簧stiff buffer spring上緊彈簧energizing spring防振氣門彈簧non-surging spring彈簧座圈spring retainer蝶形彈簧belleville spring滾柱roller 氣門室蓋valve chamber cover搖臂rocker arm高升程搖臂hig

48、h lift rocker arm搖臂軸rocker arm shaft推桿push-rod搖臂支架rocker arm bracket氣門搖臂室罩valve rocker chamber cover導向輪guide wheel 導桿slide bar導軌slide rail張緊輪tensioning wheel鏈條張緊調節裝置assembly chain tension adjuster張緊帶輪tensioning pulley傳動帶張緊裝置belt tensioner同步驅動皮帶synchronous belt同步驅動皮輪synchronous belt pulley供油系fuel sys

49、tem控制燃燒系統controlled combustion system反濕氣裝置antipercolator電子燃油噴射electronic fuel injection 蒸氣回收裝置vapor recovery system燃油蒸氣回收系統fuel vapor recovery system液體回收裝置liquid withdrawal system恒量凈化管constant purge line碳罐凈化管canister purge line供油量fuel delivery循環供油量fuel delivery per cycle額定供油量rated fuel delivery 怠速供油

50、量idling speed fuel delivery 供油規律fuel supply rate curve油量調節裝置fuel control unit供油提前角fuel supply advance angle進油計量inlet metering幾何供油行程geometric fuel delivery stroke供油率fuel supply rate燃油通道fuel gallery有效行程effective stroke剩余行程remainder stroke變行程計量variable stroke metering等容卸載constant volume unloading 變?nèi)菪遁dv

51、ariable volume unloading 收縮容積retraction volume燃油噴油裝置fuel injection equipment燃油噴射泵fuel injection pump滾輪式燃油噴射泵roll fuel injection pump凸輪軸式燃油噴射泵camshaft fuel injection pump直列式燃油噴射泵in-line fuel injection pump伺服式燃油噴射泵servo fuel injection pump底部突緣安裝燃油噴射泵base flanged mounted fuel injection pump上部安裝燃油噴射泵high flanged-mounted fuel injection pump側向安裝燃油噴射泵side-mounted fuel injection pump端部突緣安裝式燃油噴射泵end flang