352口腔刻錄課件修復設計

1、Removable Partial DentureModel designing 模型設計魏 斌What Is the Model Designing ?Clinical steps (complaint, history,examination)Laboratory steps -Model designingSystem DesignFor Dentures復習義齒修復的全過程了解”模型設計”的所處的位置及重要性ProcedureStudy castSurveyor1. Surveying2. To choose the insert-path3. Final designing模型觀測選

2、擇就位道義齒的最后設計研究模觀測儀1. surveyingWith the help of the surveyorObservation,measurement and markingAccording to it, to choose The path of insertion its the aim of the surveyingSurveying rodcast working plateSurveyorAnalysing rodGraphite markerUndercut gaugeTrimming knifeSurveying rod Several kinds of rods

3、Analysing rod1. To find and identify the undercut （倒凹） 2. To determine the parallelism of the surfacesGraphite markerTo identify and markthe position of maximum convexitySURVEY LINE (觀測線)review?ChangeableUndercut and non-undercutUndercut gauge （倒凹計）1. To measure the extent of horizontal undercut2. A

4、djusting the vertical position of the gauge until the head contact the surface of the teeth 3. Following sizes are available : 0.25, 0.5,0.75(mm)position of The retentive clasp type and material of the clasp 0.75trimming knifeTo eliminate unwanted undercuts wax is added The excess is removed A dupli

5、cate cast is made2. Path of Insertion Why should we choose the Path of Insertion? How to choose the Path of Insertion? Why should we choose the Path of Insertion? AppearanceInterferenceRetentionAppearanceInsert verticallyInsert forwardInterferenceInsert verticallyInsert forwardRetentionPath of inser

6、tion (1)Path of displacement(2)Path of withdraw (3) The angleOcclusal plane3 How to choose the Path of Insertion?Working plate To tilt the working plate and castChange the angle between the analysing rod and the occlusal planeRelationship between the rod and castRod= the path of insertionAppearanceE

7、xample 1?Tiled casts前傾后傾左側傾斜右側傾斜前后左右Example 2Average 將缺牙區前后基牙鄰面的倒凹或左右兩側基牙舌側的倒凹進行平均分配。適用于基牙傾斜扭轉，倒凹明顯者。使用均凹法后可避免一側倒凹過大，方便義齒就位。角平分線Example 3調凹法： 是根據義齒固位的需要，有意識地將模型向近遠中或左右向傾斜，使倒凹集中在某一側以增強固位。適用于基牙倒凹不大，無明顯傾斜移位者。Example 43. Final surveyDifferent survey lineDifferent clasp design (include the kind,position,

8、and etc.)3.最后設計（final survey) 根據模型設計,結合臨床檢查,確定就位道方向.根據所確定的就位道畫出基牙觀測線.確定使用的固位體類型及安放的位置.確定間接固位體、大小連接體、支架的位置及基托伸展的范圍。填倒凹設計方案確定后，即可明確基牙和軟組織倒凹的位置和大小。目的：方便義齒的取戴，同時避免過大的縫隙。方法：人造石填補，運用帶刃的觀測桿修整石膏。 確定頜位關系及上合架 頜位記錄的三種方法P235 頜位記錄的方法頜位記錄（recording jaw relationship)目的：將上下頜間正確的咬合關系轉移到合架上，為義齒制作提供依據，具有非常重要的作用。 方法 余留牙確定法蠟合記錄法合堤記錄法1.余留牙確定法適用：缺牙少，上下頜模型對合好臨床操作6 缺失右側位左側位2.蠟合記錄法適用：口腔內有咬合關系，而模型上咬合關系不穩定（余留牙體磨耗、缺損、傾斜、移位，造成上下頜牙對應鎖結關系不明顯 ）蠟合(2-3層蠟片,寬約1cm)臨床操作3. 合堤記錄法 最常用的測合方法適用：模型上咬合不穩定，或喪失正確咬合 關系患者. a 多數牙缺失,僅有個別牙上下對應 b 末端游離缺失,大部分前牙缺失 c 上下頜無對應牙或單頜缺失 d 錯誤的咬合關系，如偏頜、垂直距離降低 （磨耗、后牙缺失）合堤(occl