內(nèi)容成果bmw g38文件carrier

1、Title : LM-0030Site :Lead mouldProduct name: Sidebolster Plastic RH/LH 3D file name : 3082296_1_7403931_F_1_A_5P_FRGMOD_MD_LI_SEITENTEIL_K8_A_F_PRJG_JCI_123082297_1_7403932_F_1_A_5P_FRGMOD_MD_RE_SEITENTEIL_K8_A_F_PRJG_JCI_1Date : 2015.06.30 Confidential Design. Build. Ship. Service.LeadMouldProduct

2、informationSegment :BMW G38Thickness :2MMProject name :LM-0030 PM/PE Part name :Sidebolster Plastic RH/LH DFM by:Yang shuang huiPart No:3082296_1_74039313082297_1_7403932 Checked by:REVDate Update or added slidersBRemark:781.64MM201.04MM171.82MM3082296_1_7403931781.64MM201.04MM171.82MM3082297_1_7403

3、932Tool informationResin material : ABS Resin supplier:N/AResin GradeN/ATonnageN/A Runner Sys:Needle valesNo. of Hot Tip2Tool type :2 plateGate type :Banana gate Automatic:YNo. of Gate .(each part)2Part weight (g) :316gCavity steelGS1.2738HH(HRC34-38)Forecast volume (shot)298024 mm3Special tool :Inc

4、oeCore steelGS1.2738HH(HRC34-38) No. of Cavity:1+1Cosmetic part (Y/N):N/ASlider steel/ Family with:Cosmetic finishingLifter steelGS1.2343(HRC48-52)Need your input and correction to below information:Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateGate layoutCu

5、stomer comment. (please give your approval and comments)OK or NGremarkApproval by:date2.5MM5X0.2mm(reduce plastic減膠)Update Part LayoutNeed to show part layout to avoid customer mis-understood our proposalTool topNotes: this layout is base on estimation as a ref for tool design.2 Drops valve +Banana

6、gate Update shrinkageCustomer comment. (please give your approval and comments)OK or NGremarkApproval by:dateNotes: above shrinkage is estimated according to our understanding, pls correct it if there is any risk of getting right dimensionShrinkage with orientationX1.0055Y1.0055Z1.0055YXParting line

7、 Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateParting line is defined as edge formed by Core / Cavity parting surfaces. P/ LINENotes: please advice any concern on propose parting line.Slider/ LINECorePLCavity Parting line Customer comment. (please give your

8、 approval and comments)OK or NGremarkApproval by:dateParting line is defined as edge formed by Core / Cavity parting surfaces. P/ LINENotes: please advice any concern on propose parting line.Slider/ LINECorePLCavity Slider Customer comment. (please give your approval and comments)OK or NGremarkAppro

9、val by:dateNotes: please advice any concern on witness line form by Slider.Slider Slider Customer comment. (please give your approval and comments)OK or NGremarkApproval by:dateNotes: please advice any concern on witness line form by Slider.Slider Slider Slider Core insert Customer comment. (please

10、give your approval and comments)OK or NGremarkApproval by:dateNotes: please advice any concern on witness line form by inserting.Core insert pin Notes: please advice any concern on witness line form by inserting.Core insert pin Draft angle informationProduct is checked in UG as per the direction of

11、tooling release. This will help to evaluate draft angle and propose draft requirements.PL is decided on the basis of draft direction , if need, propose to reverse the draft angle or increase it for release the product easy. Mold opening directionEjector pin marksCustomer comment. (please give your a

12、pproval and comments)OK or NGremarkApproval by:dateNote: only show the preliminary position and size, See layout for detail.Ejector pin 12Ejector pin 6Slider thicknessCustomer comment. (please give your approval and comments)OK or NGremarkApproval by:dateIssue: Thick wall will cause sink mark.Propos

13、al: Change the design as the design guidelineNote: Thick ribs often cause sink and cosmetic problems on the opposite surface of the wall. Please refer the rib design guideline to modify as below:The red area may have sink mark.EngravingCustomer comment. (please give your approval and comments)OK or

14、NGRemarkApproval by:datedate marks month/year:material indication：article number：Recycle stamp:Cavity number：EngravingCustomer comment. (please give your approval and comments)OK or NGRemarkApproval by:datedate marks month/year:material indication：article number：Recycle stamp:Cavity number：Cosmetic requirementCustomer comment. (please give your approval and comments)OK or NGremark