某省電信匯聚交換機OLT雙上行配置模板

1 匯聚交換機 OLT 雙上行配置 模板 V2 華為 S8505 模式一：單鏈路 +Smar-link 1. 板卡硬件要求： 要求板卡中帶有“ DB”字樣并且軟件版本在 1267 以上、或者沒有“ DB”字樣軟件版本在 1628 以上，可以支持靈活 QinQ 。 2. 軟件版本要求： Release1600 以上可以配 Smart-link 3. 配置命令 定義 VLAN ACL acl number 4001 rule 0 permit ingress 51 to 1050 egress any /匹配普通寬帶撥號用戶 VLAN rule 1 permit ingress 43 egress any /匹配 iTV 用戶 VLAN rule 2 permit ingress 45 egress any /匹配 ITMS 終端管理 VLAN 定義外層 VLAN vlan 501-502 901-902 1701-1702 smart-link 配置 stp region-configuration instance 1 vlan 501 901 1701 instance 2 vlan 502 902 1702 active region-configuration /每次更改配置后必須執行這條命令才生效 smart-link group 1 preemption mode role /啟用故障鏈路恢復后的自動倒換功能 protected-instance 1 undo flush enable smart-link group 2 preemption mode role /啟用故障鏈路恢復后的自動倒換功能 protected-instance 2 undo flush enable interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable 2 traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901 /system-index 一般按順序排列，只要不重復即可。 interface GigabitEthernetX/X/X /下行接口 2 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 502 902 1702 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 4 nested-vlan 502 traffic-redirect inbound link-group 4001 rule 1 system-index 5 nested-vlan 1702 traffic-redirect inbound link-group 4001 rule 2 system-index 6 nested-vlan 902 interface GigabitEthernetX/X/X-01 /端口做為 instance 1 主用， instance 2 備用 port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 port smart-link group 1 master port smart-link group 2 slave interface GigabitEthernetX/X/X-02 /端口做為 instance 1 備用， instance 2 主用 port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 port smart-link group 1 slave port smart-link group 2 master 雙網管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 為網絡管理服務器段 4. 業務調試驗證命令 display smart-link group 1 模式二：鏈路捆綁 +Smart-link 1. 板卡硬件要求： 要求板卡中帶有“ DB”字樣并且軟件版本在 1267 以上、或者沒有“ DB”字樣軟件版本在 1628 以上，可以支持靈活 QinQ 。 3 2. 軟件版本要求： Release1600 以上可以配 Smart-link 3. 配置命令 定義 VLAN ACL acl number 4001 rule 0 permit ingress 51 to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress 45 egress any 定義外層 VLAN vlan 501 1701 901 定義鏈路組 link-aggregation group 1 mode manual link-aggregation group 2 mode manual smart-link 配置 stp region-configuration instance 1 vlan 501 901 1701 active region-configuration /每次更改配置后必須執行這條命令才生效 smart-link group 1 preemption mode role /啟用故障鏈路恢復后的自動倒換功能 protected-instance 1 link-aggregation group 1 master /鏈路組 1 作為 master link-aggregation group 2 slave /鏈路組 2 作為 slave undo flush enable interface GigabitEthernetX/X/X /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901 /system-index 一般按順序排列，只要不重復即可。 interface GigabitEthernetX/X/X-01 /主用上行口 -1 port link-type trunk port trunk permit vlan 48 50 501 901 1701 port link-aggregation group 1 /把端口加入 link-aggregation group 1 4 interface GigabitEthernetX/X/X-02 /主用上行口 -2 port link-type trunk port trunk permit vlan 48 50 501 901 1701 port link-aggregation group 1 /把端口加入 link-aggregation group 1 interface GigabitEthernetX/X/X-03 /備用上行口 -1 port link-type trunk port trunk permit vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入 link-aggregation group 2 interface GigabitEthernetX/X/X-04 /備用上行口 -2 port link-type trunk port trunk permit vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入 link-aggregation group 2 雙網管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 為網絡管理服務器段 4. 業務調試驗證命令 display smart-link group 1 display link-aggregation verbose 模式三：單鏈路 /鏈路捆綁 +VLAN 雙向透傳 1. 板卡硬件要求： 要求板卡 中帶有“ DB”字樣并且軟件版本在 1267 以上、或者沒有“ DB”字樣軟件版本在 1628 以上，可以支持靈活 QinQ。 2. 軟件版本要求： 無特殊要求 3. 配置命令 定義 VLAN ACL acl number 4001 rule 0 permit ingress 51 to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress 45 egress any 5 定義外層 VLAN vlan 501 1701 901 VLAN 雙 向透傳配置 interface GigabitEthernetX/X/X /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901 /system-index 一般按順序排列，只要不重復即可。 interface GigabitEthernetX/X/X-01 /上行口 1 port link-type trunk port trunk permit vlan 48 50 501 901 1701 interface GigabitEthernetX/X/X-02 /上行口 2 port link-type trunk port trunk permit vlan 49 501 901 1701 雙網管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 為網絡管理服務器段 4. 業務調試驗證命令 display vlan X/X/X 華為 S9300 模式一：單鏈路 +Smar-link 靈活 QINQ 配置：（ S9300 主機版本為 V100R001 版本或業務單板類型最后一個字母為 A的單板使用如下流策略配置靈活 QINQ） 6 1、 定義內 層 VLAN 的流策略： traffic classifier QINQA-1 if-match vlan-id 51 to 1050 /匹配普通寬帶撥號用戶 VLAN traffic classifier QINQA-2 if-match vlan-id 43 /匹配 iTV 用戶 VLAN traffic classifier QINQA-3 if-match vlan-id 45 /匹配 ITMS 終端管理 VLAN # traffic behavior QINQA-1 nest top-most vlan-id 501 /外層 VLAN traffic behavior QINQA-2 nest top-most vlan-id 901 /外層 VLAN traffic behavior QINQA-3 nest top-most vlan-id 1701 /外層 VLAN # traffic behavior QINQB-1 nest top-most vlan-id 502 /外層 VLAN traffic behavior QINQB-2 nest top-most vlan-id 902 /外層 VLAN traffic behavior QINQB-3 nest top-most vlan-id 1702 /外層 VLAN # traffic policy QINQA classifier QINQA-1 behavior QINQA-1 classifier QINQA-2 behavior QINQA-2 classifier QINQA-3 behavior QINQA-3 traffic policy QINQB classifier QINQA-1 behavior QINQB-1 classifier QINQA-2 behavior QINQB-2 classifier QINQA-3 behavior QINQB-3 2、 定義外層 VLAN vlan batch 501 502 901 902 1701 1702 3、 接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound # 7 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy QINQB inbound # 靈活 QINQ 配置：（ S9300 主機版本為 V100R002 版本或業務單板最后一個字母非 A 的單板使用如下 STACKING 配置靈活 QINQ） 1、 定義外層 VLAN vlan batch 501 502 901 902 1701 1702 2、接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501 port vlan-stacking vlan 43 stack-vlan 901 port vlan-stacking vlan 45 stack-vlan 1701 # interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 502 port vlan-stacking vlan 43 stack-vlan 902 port vlan-stacking vlan 45 stack-vlan 1702 # smart-link 配置 stp region-configuration instance 1 vlan 501 901 1701 instance 2 vlan 502 902 1702 active region-configuration /每次更改 配置后必須執行這條命令才生效 smart-link group 1 protected-vlan reference-instance 1 restore enable /啟用故障鏈路恢復后的自動倒換功能 smart-link enable 8 port GigabitEthernet1/0/1 master port GigabitEthernet1/0/2 slave timer wtr 30 /配置主端口恢復 30s 后 恢復 smart-link group 2 protected-vlan reference-instance 1 restore enable /啟用故障鏈路恢復后的自動倒換功能 smart-link enable port GigabitEthernet1/0/2 master port GigabitEthernet1/0/1 slave timer wtr 30 /配置主端口恢復 30s 后恢復 # interface GigabitEthernet1/0/1 /端口做為 instance 1 主用， instance 2 備用 port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 # interface GigabitEthernet1/0/2 /端口做為 instance 1 備用， instance 2 主用 port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 雙網管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 為網絡管理服務器段 業務調試驗證命令 display smart-link group 1 模式二：鏈路捆綁 +Smart-link 靈活 QINQ 配置：（ S9300 主機版本為 V100R001 版本或業務單板類型最后一個字母為 A的單板使用如下流策略配置靈活 QINQ） 1、 定義內層 VLAN 的流策略： traffic classifier QINQA-1 if-match vlan-id 51 to 1050 /匹配普通寬帶撥號用戶 VLAN traffic classifier QINQA-2 if-match vlan-id 43 /匹 配 iTV 用戶 VLAN traffic classifier QINQA-3 9 if-match vlan-id 45 /匹配 ITMS 終端管理 VLAN # traffic behavior QINQA-1 nest top-most vlan-id 501 /外層 VLAN traffic behavior QINQA-2 nest top-most vlan-id 901 /外層 VLAN traffic behavior QINQA-3 nest top-most vlan-id 1701 /外層 VLAN # traffic behavior QINQB-1 nest top-most vlan-id 502 /外層 VLAN traffic behavior QINQB-2 nest top-most vlan-id 902 /外層 VLAN traffic behavior QINQB-3 nest top-most vlan-id 1702 /外層 VLAN # traffic policy QINQA classifier QINQA-1 behavior QINQA-1 classifier QINQA-2 behavior QINQA-2 classifier QINQA-3 behavior QINQA-3 traffic policy QINQB classifier QINQA-1 behavior QINQB-1 classifier QINQA-2 behavior QINQB-2 classifier QINQA-3 behavior QINQB-3 2、 定義外層 VLAN vlan batch 501 502 901 902 1701 1702 3、 接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound # interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy QINQB inbound 10 # 靈活 QINQ 配置：（ S9300 主機版本為 V100R002 版本或業務單板最后一個字母非 A 的單 板使用如下 STACKING 配置靈活 QINQ） 1、 定義外層 VLAN vlan batch 501 502 901 902 1701 1702 2、接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501 port vlan-stacking vlan 43 stack-vlan 901 port vlan-stacking vlan 45 stack-vlan 1701 # interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 502 port vlan-stacking vlan 43 stack-vlan 902 port vlan-stacking vlan 45 stack-vlan 1702 # smart-link 配置 stp region-configuration instance 1 vlan 501 901 1701 instance 2 vlan 502 902 1702 active region-configuration /每次更改配置后必須執行這條命令才生效 smart-link group 1 protected-vlan reference-instance 1 restore enable /啟用故障鏈路恢復后的自動倒換功能 smart-link enable port Eth-Trunk1 master port Eth-Trunk2 slave timer wtr 30 /配置主端口恢復 30s 后恢復 smart-link group 2 protected-vlan reference-instance 1 restore enable /啟用故障鏈路恢復后的自動倒換功能 11 smart-link enable port Eth-Trunk2 master port Eth-Trunk1 slave timer wtr 30 /配置主端口恢復 30s 后恢復 # interface GigabitEthernetX/X/X-01 /主用上行口 -1 Eth-Trunk1 /把端口加入 link-aggregation group 1 interface GigabitEthernetX/X/X-02 /主用上行口 -2 Eth-Trunk1 /把端口加入 link-aggregation group 1 interface GigabitEthernetX/X/X-03 /備用上行口 -1 Eth-Trunk2 /把端口加入 link-aggregation group 2 interface GigabitEthernetX/X/X-04 /備用上行口 -2 Eth-Trunk2 /把端口加入 link-aggregation group 2 interface Eth-Trunk1 /端口做為 instance 1 主用， instance 2 備用 port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 # interface Eth-Trunk2 /端口做為 instance 1 備用， instance 2 主用 port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 雙網 管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 為網絡管理服務器段 業務調試驗證命令 display smart-link group 1 display link-aggregation verbose 模式三：單鏈路 /鏈路捆綁 +VLAN 雙向透傳 靈活 QINQ 配置：（ S9300 主機版本為 V100R001 版本或業務單板類型最后一個字母為 A的單板使用如下流策略配置靈活 QINQ） 12 1、 定義內層 VLAN 的流策略： traffic classifier QINQA-1 if-match vlan-id 51 to 1050 /匹配普通寬帶撥號用戶 VLAN traffic classifier QINQA-2 if-match vlan-id 43 /匹 配 iTV 用戶 VLAN traffic classifier QINQA-3 if-match vlan-id 45 /匹配 ITMS 終端管理 VLAN # traffic behavior QINQA-1 nest top-most vlan-id 501 /外層 VLAN traffic behavior QINQA-2 nest top-most vlan-id 901 /外層 VLAN traffic behavior QINQA-3 nest top-most vlan-id 1701 /外層 VLAN # traffic behavior QINQB-1 nest top-most vlan-id 502 /外層 VLAN traffic behavior QINQB-2 nest top-most vlan-id 902 /外層 VLAN traffic behavior QINQB-3 nest top-most vlan-id 1702 /外層 VLAN # traffic policy QINQA classifier QINQA-1 behavior QINQA-1 classifier QINQA-2 behavior QINQA-2 classifier QINQA-3 behavior QINQA-3 traffic policy QINQB classifier QINQA-1 behavior QINQB-1 classifier QINQA-2 behavior QINQB-2 classifier QINQA-3 behavior QINQB-3 2、 定義外層 VLAN vlan batch 501 502 901 902 1701 1702 3、 接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound # 13 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy QINQB inbound # 靈活 QINQ 配置：（ S9300 主機版本為 V100R002 版本或業務單板最后一個字母非 A 的單板使用如下 STACKING 配置靈活 QINQ） 1、定義外層 VLAN vlan batch 501 502 901 902 1701 1702 2、接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501 port vlan-stacking vlan 43 stack-vlan 901 port vlan-stacking vlan 45 stack-vlan 1701 # interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 為 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 502 port vlan-stacking vlan 43 stack-vlan 902 port vlan-stacking vlan 45 stack-vlan 1702 # interface GigabitEthernetX/X/X-01 /上行口 1 port link-type trunk port trunk permit vlan 48 50 501 901 1701 interface GigabitEthernetX/X/X-02 /上行口 2 port link-type trunk port trunk permit vlan 49 501 901 1701 雙網管地址配置 interface vlan 48 14 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 為網絡管理服務器段 業務調試驗證命令 display vlan X/X/X 中興 T64G 模式一：單鏈路 +ZESS-link 1. 板卡硬件要求： 每臺 T64G 至少配置 1 塊 UGSF 板卡 2. 軟件版本要求： V2.8.01B19 或 V2.8.01C20 以上 3. 配置命令 全局配置 STP spanning-tree enable /全局配置為 stp enable，所有端口配置為 stp disable spanning-tree mst configuration instance 1 vlan 501,1701.901 instance 2 vlan 502,1702.902 端口配置 interface gei_1/1 /下行 customer-port 配置 switchport mode hybrid switchport hybrid native vlan 501 /見注意事項 1 switchport hybrid vlan 50 tag switchport hybrid vlan 901 untag switchport hybrid vlan 1701 untag switchport qinq customer /定義端口為 C 口 spanning-tree disable /關閉 STP interface gei_1/2 /下行 customer-port 配置 switchport mode hybrid switchport hybrid native vlan 502 /見注意事項 1 switchport hybrid vlan 50 tag switchport hybrid vlan 902 untag switchport hybrid vlan 1702 untag 15 switchport qinq customer /定義端口為 C 口 spanning-tree disable /關閉 STP interface gei_1/24 /上行 uplink-port 配置 switchport mode hybrid switchport hybrid native vlan 48 switchport hybrid vlan 48 tag switchport hybrid vlan 50 tag switchport hybrid vlan 501-502 tag switchport hybrid vlan 1701-1702 tag switchport hybrid vlan 901-902 tag switchport hybrid vlan 2 untag switchport qinq uplink /定義端口為 U 口 spanning-tree disable /關閉 STP interface gei_2/24 /上行 uplink-port 配置 switchport mode hybrid switchport hybrid native vlan 49 switchport hybrid vlan 49 tag switchport hybrid vlan 501-502 tag switchport hybrid vlan 1701-1702 tag switchport hybrid vlan 901-902 tag switchport qinq uplink /定義端口為 U 口 spanning-tree disable /關閉 STP session 設置 vlan qinq session-no 1 customer-port gei_1/1 uplink-port gei_1/24 in-vlan 50 untag helper-vlan 2 undirect vlan qinq session-no 2 customer-port gei_1/1 uplink-port gei_1/24 in-vlan 2051-3050 ovlan 1701 undirect vlan qinq session-no 3 customer-port gei_1/1 upl